Hi - interesting video, thanks. I am considering using this on a Danfoss compressor on my boat's refrigerator. Where on the compressor module would the yellow and black wires be connected to?
Hi, I am not familiar with boat or equipment installed on boat. But find two main wires of refrigerator and follow what I have shown. I hope you paid attention that we have power for this module to work and then relay two wires to control the load (your fridge is load).
May be you missed reading the title which says DC or you skipped the introduction which I mentioned it is DC or may be you don't know what DC is. DC is power from battery with fixed + and - terminals. Here is the AC version of this ua-cam.com/video/kZlTMNqXzo4/v-deo.html
Can i Use this for both AC/DC voltage? For example for slow cooker ? Put 220 AC voltage IN and in output will be a electrical socket where I plug slow cooker, is it possible ? I have version 220V 1500W
I don't understand your question. there is two voltage. 1-operating voltage which can be AC or DC depending on they you purchased. 2-Controlling load voltage which can be anhything.
@@robojax I meant if source or power supply can be also a 220 V from socket and if it could be also Alternating volatage, but I have tested it and it is working well so no problem
12v DCis just voltage does not matter where it comes from. But it must not go higher than 13V . Then the load is loads as I explained, the limit. You can connect any load.
Hi , İ am using that But sometimes it doesn't work when degrees increase for the stop . for example i setting to stop 40 °C then i want to stop it but its working up How i control
thanks for your video sir and I have one question. I have same DC meter but I don't know how to work for incubator with 60w bulbs can you explain for me Please
( calbration please )If the room temp. on the module is incorrect, how to correct it. Pressing both buttons at the same time show a digit what is it. . thank you
Hi - interesting video, thanks. I am considering using this on a Danfoss compressor on my boat's refrigerator. Where on the compressor module would the yellow and black wires be connected to?
Hi, I am not familiar with boat or equipment installed on boat. But find two main wires of refrigerator and follow what I have shown. I hope you paid attention that we have power for this module to work and then relay two wires to control the load (your fridge is load).
Thanks very helpful
You are welcome. The best thank you for me is to subscribe to my channel. Thank you.
what type of powersupply are yoy using Sir? tnx
something like this amzn.to/3jKKupt
how to use it? plug in to 220V ac outlet or a DC battery can do?
May be you missed reading the title which says DC or you skipped the introduction which I mentioned it is DC or may be you don't know what DC is. DC is power from battery with fixed + and - terminals. Here is the AC version of this ua-cam.com/video/kZlTMNqXzo4/v-deo.html
Can i Use this for both AC/DC voltage? For example for slow cooker ? Put 220 AC voltage IN and in output will be a electrical socket where I plug slow cooker, is it possible ? I have version 220V 1500W
I don't understand your question. there is two voltage. 1-operating voltage which can be AC or DC depending on they you purchased. 2-Controlling load voltage which can be anhything.
@@robojax I meant if source or power supply can be also a 220 V from socket and if it could be also Alternating volatage, but I have tested it and it is working well so no problem
I understand that it can control a device up to 10 amp. What amp does the unit itself draw when the controlled device is not powered?
10mA for the chip and about 30-60mA for the display. When relay is turned ON, it consumes additional 50-80mA
Are there any 48v DC temperature controllers?
No. it is offered at 12V and 24V. you may buy a boost converter to convert 12V to 48V.
Can I wire this to a 12v Solar charge controller?
Then use a 12v, 15W, silicone heater as the heating element?
12v DCis just voltage does not matter where it comes from. But it must not go higher than 13V . Then the load is loads as I explained, the limit. You can connect any load.
Thanks for the help man! ❤️
Good question, I am doing the same thing.
how much load can we put on it ? I want to use dc water heater around 150 to 200watts dc
Read the relay. If it is 10A at 220v the 220x10=2200W. Do the math
@@robojax DC 12v
It is not voltage. It is the current in Ampere. P
I mentioned the relay in the video
My XH-W3001 shows the Temperatur in Fahrenheit not in °C, How can i change this ?
never seen the F version of this. Actually I was searching to purchase both versions but could not find it. contact the seller.
What would happen if i use a 24v power supply on the model rated for 12v?
It will die
Hi , İ am using that But sometimes it doesn't work when degrees increase for the stop . for example i setting to stop 40 °C then i want to stop it but its working up How i control
using is for heater and cooler is different. Pay attention when I explained.
@@robojax i using at heater System is true But sometimes the system contunues to work
For , example İ want to stop 38°C but its not stoping and contuniue high degrees
it should stop working when it reaches at 38. it seems the module is defective or you have wrong settings
👍🇵🇱
Nice...and please make Arduino mega with include Wi-Fi board video tutorial.
You are welcome. I just put that in my list. I will make video once I received the module.
thanks for your video sir and I have one question. I have same DC meter but I don't know how to work for incubator with 60w bulbs can you explain for me Please
I know know to how to set this. I have no knowledge of incubator. Bing or google it
( calbration please )If the room temp. on the module is incorrect, how to correct it. Pressing both buttons at the same time show a digit what is it. . thank you
this module doesn't have features. I have other module which has it ua-cam.com/users/robojaxTVsearch?query=thermostat