I'v got just a quick question. I just set up a new Flylens 85 with the DJI 03 unit and the new V2 GOKU F404 HD 1-2S ELRS AIO V2 Board, and everything is working great. I am just wanting to control the LEDs on a switch, I normally use the LEDLOW tab in the modes menu but I noticed that User 1 was turned on and if I use this I CAN turn the LEDs on and off with a switch BUT after reading on your site that the User 1 is to be used to turn off the new 9 Volt regulator. I guess by turning off the 9 volt regulator I'm turning off the power to the LEDs. How do I go about about still using the User 1 for the 9 V regulator and also using another switch for the LEDs, can I do this. The LedLow tab under Modes is not working to switch the leds. Thanks for any Help
guess for walksnail i will put a 4 connector on remove yellow wire. DJI is okay but costly and a new one just came out so that be a new pair of goggles I am betting on walksnail catching up or at least comparable
Yes. It’s possible. I bought the plug n play kit and added 03. The quad comes with 2 cables pre installed. One cable for any receiver is soldered to Uart 3. The other, for DJI, on which rx / tx / gnd are wired to uart6. VBatt /Sbus are wired to 5. In betaflight rcvr tab, turn port 3 off, set serial rx port 5 to on. Turn on port 6 and set peripherals to vtx msp + display.
Great job Flywoo! Can’t wait to see more info on Flylens85. If it flies as good as it looks, you will sell a lot of these.
I got the PNP version, I’m looking to use the DJI Controller. What do I do with the PNP cable? It’s not shown in this video.
I'v got just a quick question. I just set up a new Flylens 85 with the DJI 03 unit and the new V2 GOKU F404 HD 1-2S ELRS AIO V2 Board, and everything is working great.
I am just wanting to control the LEDs on a switch, I normally use the LEDLOW tab in the modes menu but I noticed that User 1 was turned on and if I use this I CAN turn the LEDs on and off with a switch BUT after reading on your site that the User 1 is to be used to turn off the new 9 Volt regulator.
I guess by turning off the 9 volt regulator I'm turning off the power to the LEDs. How do I go about about still using the User 1 for the 9 V regulator and also using another switch for the LEDs, can I do this. The LedLow tab under Modes is not working to switch the leds.
Thanks for any Help
guess for walksnail i will put a 4 connector on remove yellow wire. DJI is okay but costly and a new one just came out so that be a new pair of goggles I am betting on walksnail catching up or at least comparable
Can you do a flylens85 frame assembly video?
what is the total weight and flight time using the "standard" o3 version? Tanks
Hi,what version of elrs does it come with?
Beautiful frame ! So we can buy it without o3 ?
yes. you can choose drone kit
hoping to get this soon
is it possible to control the flylens through the DJI FPV Controller 2?
Yes you have buy pnp model
@@talknuff thank you. but if I want to have both the ELRS and DJI controller on the same quad, is it possible?
@@vernelfpv i want to know too? is it possible?
Yes. It’s possible. I bought the plug n play kit and added 03. The quad comes with 2 cables pre installed. One cable for any receiver is soldered to Uart 3. The other, for DJI, on which rx / tx / gnd are wired to uart6. VBatt /Sbus are wired to 5. In betaflight rcvr tab, turn port 3 off, set serial rx port 5 to on. Turn on port 6 and set peripherals to vtx msp + display.
Send me pid setting flylens 85. I lost it, can't fix it. Pliss send me pid setting 🙏
淘寶什麼時候上架?
星期五
What flight controller 👀
flywoo.net/products/goku-versatile-f405-2s-12a-aio-w-build-in-elrs-2-4g-rx-mpu6000