New at this, just moved from Maintenance Mechanic to Instrumentation and Electrical Tech., i struggle to understand how is it that the motor keeps running after the start button was let go. Saw this video and is very simple, Thanks A lot.
Excellent video Walter! I have been looking for hours for how to setup a remote start for a VFD powering a 3 phase motor on a table saw. Yours by far is the simplest, most straight forward with a clear explanation of how to do it using an Ice Cube Relay and the functionality of that relay. This video provides background support for your other video: "Starting a VFD with 2-wire Start". Thank You!
Good job 👍 .. Learning in a steel mill.. seems overwhelming.. place is very loud in places and can't communicate while watching trainer.. Hard place to learn.
If you look carefully at the schematic about minute mark 2:40 you will see that 1,2, & 3 all originate from the same source. Therefore they are the same potential.
If I understand your question correctly, you should be able to connect a timer circuit in the same way that the float circuit is connected in the video link here. ua-cam.com/video/1J36SgPABFo/v-deo.html
You're using 10amps for VFD and motor control yet say that 10amp relay not to be used with anything requiring a load? 10amp is the common rating for general residential use, lights and power points, here in Australia.
The 10 amp relay is being used to on the control circuit of the VFD… not the motor circuit. The current on the control for a start signal is measured in milliamps.
@@fuzzfacelogic789 no worries. Thank you for watching and commenting on these videos. We created them to be helpful. Hopefully they accomplish that goal.
What a wonderful way of teaching. It has changed my learning experience. Keep up the good work and thank you for sharing all this information .
Walter I have a MCH36 having problems to start
Need support I am not familiar with this equipment the transformer burned and some bulbs
Definitely, the best site for controls.
New at this, just moved from Maintenance Mechanic to Instrumentation and Electrical Tech., i struggle to understand how is it that the motor keeps running after the start button was let go. Saw this video and is very simple, Thanks A lot.
Excellent video Walter! I have been looking for hours for how to setup a remote start for a VFD powering a 3 phase motor on a table saw. Yours by far is the simplest, most straight forward with a clear explanation of how to do it using an Ice Cube Relay and the functionality of that relay. This video provides background support for your other video: "Starting a VFD with 2-wire Start". Thank You!
Awesome explanation you should have a course online your step by step can’t be any better hope you continue making videos great job
Thank you Ismael!
thank you so much..im gonna look like a genius...you saved the day friend!!!
Great straight forward explanation
Keep up the good work
Awesome videos! Thanks so much!!
Good job 👍 .. Learning in a steel mill.. seems overwhelming.. place is very loud in places and can't communicate while watching trainer.. Hard place to learn.
Awesome!!!! Thank you so much!!
Great content
Excellent Video.
Excellent
Amazing Thank you Sir.
I watched you video a lot
Do the 2 wires going to VFD need to be 24 volts, or can they be 120 volts?
Awesome! 👏🏽
Great work, what program do you use for your motor control simulations? Thanks
Stephen McAdam I use The Constructor software. www.cmhsoftware.com/constructor.html
Thank you, love your work and videos
Can you control a VFD with a start stop holding circuit and a field device such as a pressure switch?
Yes you could
Why doesn't the power from 1 and 3 cause a short against the line? Or maybe electricity doesn't work this way
If you look carefully at the schematic about minute mark 2:40 you will see that 1,2, & 3 all originate from the same source. Therefore they are the same potential.
What software is your circuit drawing?
It is Constructor software
Can you wire to wire 2 wires from start to 2 and 3
Instead of jumping wires it helps me better wireing like that
What software do you use to make your videos?
Hello sir will u plzz explaine me how i conect the solenoid valve timer to auto and manual starter
If I understand your question correctly, you should be able to connect a timer circuit in the same way that the float circuit is connected in the video link here. ua-cam.com/video/1J36SgPABFo/v-deo.html
Can you just run two wires to start
You're using 10amps for VFD and motor control yet say that 10amp relay not to be used with anything requiring a load? 10amp is the common rating for general residential use, lights and power points, here in Australia.
The 10 amp relay is being used to on the control circuit of the VFD… not the motor circuit. The current on the control for a start signal is measured in milliamps.
@@AccessToPower Please excuse my ignorance.
@@fuzzfacelogic789 no worries. Thank you for watching and commenting on these videos. We created them to be helpful. Hopefully they accomplish that goal.
?
Instead of jumping wires it helps me better wireing like that