At the 2:25 mark, adjusting your side mirrors. Move them until you see the least amount of the vehicle in them, then move them so the vehicle is out of view in the mirror from the drivers seated position, once these are positioned, lean slightly left or right to see the vehicle side slightly in each mirror, this setup gets rid of 90% of the blind spots from your vehicles sides.
I WISH THAT I HAD ALL OF THE TOOLS & ACCESS TOP THE EQUIPMENT THAT YOU SEEM TO HAVE. MAYBE THEN I TOO COULD BE A UA-cam WORKSHOP INSIDER W/A COUPLE HUNDRED THOUSAND SUBSCRIBERS. BUT, NO DOUBT YOU ARE A VERY RESOURCEFUL PERSON & I THANK YOU VERY MUCH FOR ALL OF THE INSIGHT. I WILL NO DOUBT PUT A LOT OF YOUR IDEAS TO USE SOME DAY. I WILL LAUGH & I WILL THINK OF YOU FONDLY.
You guys did a great job. very smart, i learned a lot of things here, . My favorite hobby channel. maybe just a little too fast. Often I don't get it fast enough and have to rewind or speed it up by half.
Lots of great ideas. Lots of terrible ideas too; about half are more trouble than they're worth. If you would have a "Click Here to Skip to Next Clip" button, it would be great, but I suppose your monetization is higher the longer someone stays on your website, so that's not likely to happen, is it?
The tip where to place your hands on the steering wheel is wrong. Because of air bags inflation braking arms it changed to the first position (4 oclock and9 oclock) you showed. Some great ideas though. Thanks for the video.
The toiletpaper and glue for the hinge holes. You can tell he drilled out the screw holes. Why not glue wood dowles in instead of toilet paper? No dowles use toothpicks or slivers of wood. Sheesh.
there’s are 3 terminal out of the Automator wiring’s 6 diodes it converted to DC without a diode it act as an AC voltages the fastest the spin the more electricity if it’s connected it to a transformers to the secondary’s it produced a voltages out of the secondary’s voltage the fastest the spin the more electrics
I hate to be a nag, I think. But the driving around 2:50. It is best to drive with your thumbs outside the steering wheel. If in an accident your thumbs could be torn backwards adding to any misery or injury of the accident, or compound the misery of life in general.
I liked a lot of these tricks...but, there's two of them which are very dangerous. -The one in which he brewed tea in the empty juice box. Those juice boxes were never meant to have boiling liquid in them. The plastic within the box (which makes it so the paper outside doesn't disintegrate) will melt and get into your tea. It's great if you're body is running low on micro-plastics...but, very bad if you're trying to avoid that sort of thing. -Baking a potato inside of an empty soda can only SEEMS smart. But, those aluminum cans have a very thin layer of plastic inside of them which keeps the aluminum from seeping into the soda. Pretty much every metal can designed for food and beverage has that thin plastic lining. So, baking a potato within any metal food/beverage can will put microplastics in your potato. -But, I really did like the hack with the two batteries on top of the router. It's like, "Put two batteries on top of a Wi-Fi router...and, you too can have two batteries on top of a Wi-Fi rounter."
Whoever is making these videos needs to at least speak out about what it is they are intending to do or create out of these everyday items. Some of the things he or she is making don't seem to make any sense to them at all. As I said... SPEAK UP!!! & CLEARLY DESCRIBE WHAT IT IS U R DOING OR ATTEMPTING TO DO... IF U WANT A THUMBS UP RATING BECAUSE MOST OF THE ITEMS IN THE VIDEO JUST ISN'T MAKING ANY SENSE. HATED 2B BLUNT BUT CERTAIN POINTS HAVE 2B POINTED OUT THAT WAY. BEST & BETTER LUCK OF ANY FUTURE VIDEOS U MAY CREATE.
DITTO... I ALSO WOULD LIKE TO BETTER UNDERSTAND WHAT IS GOING ON, & WHAT HE/SHE IS TRYING TO ACCOMPLISH. SOME OF THE THINGS ARE EASY TO FIGURE OUT & THEN SOMETHINGS AREN'T. PLEASE EXPLAIN TO US DUMMIES, IN A LANGUAGE THAT WE CAN UNDERSTAND, EXACTLY WHAT'S GOING ON, & WHAT YOU'RE HOPING TO ACHIEVE.
Work safe without voltage? For what, it's better to wrap your fingers with electrical tape. Use your brain and drive with foresight? For what, the main thing is that my arms are at the right angle! Speaking of angles. The protective plate on the angle grinder, what is it for? Right! To dismantle it and use it as holder. And don't forget, thumbs up! Buy a thermal mug once that will last for years? Why, I'd rather build fragile scrap and produce tons of waste! How to properly learn to sharpen a knife, no matter what angle is necessary? Why, I'd rather build a stupid gadget that sharpens some blades, but completely destroys others. Let's stick sandpaper on the table and we'll show you how to remove it later in 10 other stupid life hack videos! And don't forget: thumbs up! 23:30: Omg, the screwdriver has to be deeper, you'll ruin the screws and the tool. 25:15: Very important, paint the wall first! 25:40: There's a much better trick: USE THE DAMN ANGLE ADJUSTMENT ON THE SAW!! 32:30: Let's use the black board as a stop for the saw. Nonsense, I'd much rather be making useless junk on the saw AND I might be able to make the saw blade glow because it rubs against the black board. 33:25: You noticed the mistake yourself, right? 34:21: With the spray can, seriously?? So brilliant and intended for every day, trololol.. Very weak, really!
#1 - Don't bother with the goop. Just plug the tire with the black plug, cut off the excess and let it be. #2 - Add some glue to the stripped wooden hole and break off some toothpicks inside it and wait for the glue to dry. It will be MUCH stronger. After those two stupid "fixes" I had no interest to see any more of this guys dumb stuff.
I've used those commercial tire plug kits several times with great success, and always use the goo. Why not? It also lubricates the plug to make it go in easier, which is welcome because you need to push REALLY HARD to get it through the tire. (Unfortunately, with the first really cheap kit I tried, the tool broke while trying to push the plug in. Fortunately, I was just across the street from an auto parts store, and bought a better one. I never leave home without it.) These days most shops won't plug a tire, and insist on removing the tire and patching it from the inside, for about $50... The kits work MUCH better than injectable goo, in my experience. But I believe them when they say don't patch a sidewall; way more flex than the tread, and less thickness to hold the plug.
RIDICULOUS- NEVER EVER EVER MAKE A DRYWALL HOLE BIGGER TO PATCH IT NEVER- ALWAYS PATCH IT AS SMALL AS POSSIBLE AND BTW NEVER EVER CUT BACK TO STUDS JUST TO PATCH EITHER.. NEVER
35 MINUTES & 56 SECONDS ⏲OF SOME VERY GREAT IDEAS. IT'S JUST TOO BAD THAT I'M NOT INTELLIGENT ENOUGH TO UNDERSTAND A LOT OF THEM. I REALLY WISH THAT YOU WOULD ADD SOME AUDIO, & TAKE THE TIME TO EXPLAIN EXACTLY WHAT'S GOING ON & WHY, SO THAT DUMMIES LIKE ME 🐒COULD GET THE JIST OF WHAT YOU'RE DOING, & HOPING TO ACCOMPLISH, BY DOING IT. BUT THANKS FOR ALL OF THE IDEAS THAT I DID UNDERSTAND. 🏆THEY ARE GOING TO BE VERY USEFUL TO ME IN THE FUTURE. 📆🤖 PLEASE KEEP ON POSTING THE GOOD WORK & ALL OF THE GREAT IDEAS. 👍
good morning, Could you please stop inverting your videos when you publish them, because everything is upside down, the inscriptions and the screwdrivers that unscrew to screw and vice versa! It's a real pain! Hallo! Könnten Sie bitte aufhören, Ihre Videos umzudrehen, wenn Sie sie veröffentlichen, denn alles steht auf dem Kopf, die Beschriftung und die Schraubendreher, die man aufschrauben muss, um zu schrauben und umgekehrt! Das ist wirklich mühsam! Hola, Por favor, podrías dejar de invertir tus vídeos cuando los publicas, porque todo sale al revés, ¡las inscripciones y los destornilladores que se desenroscan para enroscarse y viceversa! ¡Es realmente molesto! Salve, Potreste per favore smettere di invertire i vostri video quando li pubblicate, perché tutto è capovolto, le scritte e i cacciaviti che si svitano per avvitarsi e viceversa! È davvero fastidioso! Здравствуйте, Не могли бы вы перестать инвертировать ваши видео при публикации, а то все вверх ногами, и надписи, и отвертки, которые откручиваются, чтобы закрутить и наоборот! Это очень раздражает! 안녕하세요, 동영상을 게시할 때 모든 것이 거꾸로 되어 있고, 비문과 나사를 풀어서 나사를 조이는 드라이버가 거꾸로 되어 있기 때문에 동영상을 거꾸로 게시하는 것을 중단해 주시겠어요? 정말 짜증나요! Helló, Légyszi ne fordítsd meg a videóidat, amikor közzéteszed őket, mert minden fejjel lefelé van, a feliratok és a csavarhúzók, amelyek kicsavarodnak, hogy becsavarodjanak és fordítva! Ez nagyon idegesítő! Bonjour, Pourriez-vous arrêter d'inverser vos vidéos lorsque vous les publiez, car tout est à l'envers, les inscriptions et les tournevis qui se dévissent pour visser et vice versa ! C'est vraiment pénible !
NEXT AWESOME ua-cam.com/video/vyyApoERxcA/v-deo.html
Superrr Awesoooome 🥳 Thank you!!!!
Stick the ends of the wire in the drill chuck and tighten. You don't need to spend thirty minutes building something that holds the wire.
i like this ideas so i joined your channel wish you more success
Your videos always brighten my day
Спасибо❤❤❤❤
Thaks
👍💪
@ 4:40 What are you attaching to the shelf board. I like the idea. I am not sure it is tape/paper or some time of shelf lining material.
At the 2:25 mark, adjusting your side mirrors. Move them until you see the least amount of the vehicle in them, then move them so the vehicle is out of view in the mirror from the drivers seated position, once these are positioned, lean slightly left or right to see the vehicle side slightly in each mirror, this setup gets rid of 90% of the blind spots from your vehicles sides.
Thanks Brother and have a Merry CHRISTmas !
good tips for life
wow thanks
If you like stupid ideas, you'll find plenty here. The rebar toilet paper hanger is a classic!
tôi rất thích và tôi đang làm những video như vậy
I WISH THAT I HAD ALL OF THE TOOLS & ACCESS TOP THE EQUIPMENT THAT YOU SEEM TO HAVE. MAYBE THEN I TOO COULD BE A UA-cam WORKSHOP INSIDER W/A COUPLE HUNDRED THOUSAND SUBSCRIBERS. BUT, NO DOUBT YOU ARE A VERY RESOURCEFUL PERSON & I THANK YOU VERY MUCH FOR ALL OF THE INSIGHT. I WILL NO DOUBT PUT A LOT OF YOUR IDEAS TO USE SOME DAY. I WILL LAUGH & I WILL THINK OF YOU FONDLY.
my favourite hobby channel. maybe just little bit too fast. often i do not get it fast enough and have to rewind or go on half speed.
same here
You guys did a great job. very smart, i learned a lot of things here, . My favorite hobby channel. maybe just a little too fast. Often I don't get it fast enough and have to rewind or speed it up by half.
Fake reviews all over this channel. This one's almost word-for-word the same as one next to it by
@martinkadnar9920
Lots of great ideas.
Lots of terrible ideas too; about half are more trouble than they're worth.
If you would have a "Click Here to Skip to Next Clip" button, it would be great, but I suppose your monetization is higher the longer someone stays on your website, so that's not likely to happen, is it?
The tip where to place your hands on the steering wheel is wrong. Because of air bags inflation braking arms it changed to the first position (4 oclock and9 oclock) you showed. Some great ideas though. Thanks for the video.
At 1:19 trim the wires down and use wire nuts. Twisting the wirenuts will take care of keeping your fingers safe.
Before working on any electric wiring, make sure there is no power present. This here is just dam dumb.
Thanks
😌
O melhor
WOW VERY GOOD
@12. Just stick the bearing in a small ziplock with grease and kneed the grease into the bearing.
6:44 это отверстие проще заполнить строительной пеной и после зашпаклевать :)
Toilet paper and CA glue..will have to try that😄
Cotton balls works very well... But can heat up
I feel a little more dead inside if this accounts for handy content
@9:19. Why???? So a destroyed bulb will not go anywhere. WTF??
احسنت
The toiletpaper and glue for the hinge holes. You can tell he drilled out the screw holes. Why not glue wood dowles in instead of toilet paper? No dowles use toothpicks or slivers of wood. Sheesh.
1:02 What was that?🤔
Taking stupid to a whole new level. Save your time. Its all crap you'll never want to use.
1:20 Wrapping electrical tape around your fingers to work on live wires is a pathway to dead.
there’s are 3 terminal out of the Automator wiring’s 6 diodes it converted to DC without a diode it act as an AC voltages the fastest the spin the more electricity if it’s connected it to a transformers to the secondary’s it produced a voltages out of the secondary’s voltage the fastest the spin the more electrics
17:50 hurr hurr Semin.
Der Reifen😂
So geht das nicht 😂
Falsche Seite 😂
@12:06 spend a half hour or more to build a toilet paper holder you can buy for $6 or less. My time is worth money people.
Yeah, but it's beautiful! LOL
👍👍
Скоро будут учить как правило задницу вытирать 😊
I hate to be a nag, I think. But the driving around 2:50. It is best to drive with your thumbs outside the steering wheel. If in an accident your thumbs could be torn backwards adding to any misery or injury of the accident, or compound the misery of life in general.
17:49 what for?
I liked a lot of these tricks...but, there's two of them which are very dangerous.
-The one in which he brewed tea in the empty juice box. Those juice boxes were never meant to have boiling liquid in them. The plastic within the box (which makes it so the paper outside doesn't disintegrate) will melt and get into your tea. It's great if you're body is running low on micro-plastics...but, very bad if you're trying to avoid that sort of thing.
-Baking a potato inside of an empty soda can only SEEMS smart. But, those aluminum cans have a very thin layer of plastic inside of them which keeps the aluminum from seeping into the soda. Pretty much every metal can designed for food and beverage has that thin plastic lining. So, baking a potato within any metal food/beverage can will put microplastics in your potato.
-But, I really did like the hack with the two batteries on top of the router. It's like, "Put two batteries on top of a Wi-Fi router...and, you too can have two batteries on top of a Wi-Fi rounter."
Lifehack‘s für Russen und Ammy‘s LOL 😂
So rapidly.
31:35 Hell nooooooooo!
If he has as much money as he says he’s has,, then I think he should put 1 million in a bank in my name, then I’ll tell everyone he’s not lying.
Good share of these make no sense. Parts shake. Scene changes. No application shown. WHAT??? Nice cures for corner flooring and baseboards.
Lots of obviously fake reviews, too. This is garbage!
clips are too short too fast...
This video is WAY too fast to pick up useful tips.
Click on settings gear ⚙️ then playback speed to either slow it down or speed it up. ⚙️
It's not worth watching anyway.
Whoever is making these videos needs to at least speak out about what it is they are intending to do or create out of these everyday items. Some of the things he or she is making don't seem to make any sense to them at all. As I said... SPEAK UP!!! & CLEARLY DESCRIBE WHAT IT IS U R DOING OR ATTEMPTING TO DO... IF U WANT A THUMBS UP RATING BECAUSE MOST OF THE ITEMS IN THE VIDEO JUST ISN'T MAKING ANY SENSE. HATED 2B BLUNT BUT CERTAIN POINTS HAVE 2B POINTED OUT THAT WAY. BEST & BETTER LUCK OF ANY FUTURE VIDEOS U MAY CREATE.
DITTO... I ALSO WOULD LIKE TO BETTER UNDERSTAND WHAT IS GOING ON, & WHAT HE/SHE IS TRYING TO ACCOMPLISH. SOME OF THE THINGS ARE EASY TO FIGURE OUT & THEN SOMETHINGS AREN'T. PLEASE EXPLAIN TO US DUMMIES, IN A LANGUAGE THAT WE CAN UNDERSTAND, EXACTLY WHAT'S GOING ON, & WHAT YOU'RE HOPING TO ACHIEVE.
Siamo in Italia, perciò sarebbe meglio parlare in italiano
Ciao,
Fai quello che faccio io. Copia i testi che ti interessano e incollali in DEEPL, che traduce correttamente in tutte le lingue.
STUPID IS AS STUPID DOES WITH MOST OF WHAT YOU SEE HEAR. DANGEROUS IS WHAT I MAINLY SEE
Many of these are useless. I watched almost 5 minutes before realize it was a waste of time.
Work safe without voltage? For what, it's better to wrap your fingers with electrical tape.
Use your brain and drive with foresight? For what, the main thing is that my arms are at the right angle!
Speaking of angles. The protective plate on the angle grinder, what is it for? Right! To dismantle it and use it as holder. And don't forget, thumbs up!
Buy a thermal mug once that will last for years? Why, I'd rather build fragile scrap and produce tons of waste!
How to properly learn to sharpen a knife, no matter what angle is necessary? Why, I'd rather build a stupid gadget that sharpens some blades, but completely destroys others.
Let's stick sandpaper on the table and we'll show you how to remove it later in 10 other stupid life hack videos! And don't forget: thumbs up!
23:30: Omg, the screwdriver has to be deeper, you'll ruin the screws and the tool.
25:15: Very important, paint the wall first!
25:40: There's a much better trick: USE THE DAMN ANGLE ADJUSTMENT ON THE SAW!!
32:30: Let's use the black board as a stop for the saw. Nonsense, I'd much rather be making useless junk on the saw AND I might be able to make the saw blade glow because it rubs against the black board.
33:25: You noticed the mistake yourself, right?
34:21: With the spray can, seriously??
So brilliant and intended for every day, trololol.. Very weak, really!
warum nur kan man nur 1 dislike geben
#1 - Don't bother with the goop. Just plug the tire with the black plug, cut off the excess and let it be.
#2 - Add some glue to the stripped wooden hole and break off some toothpicks inside it and wait for the glue to dry. It will be MUCH stronger.
After those two stupid "fixes" I had no interest to see any more of this guys dumb stuff.
I've used those commercial tire plug kits several times with great success, and always use the goo. Why not? It also lubricates the plug to make it go in easier, which is welcome because you need to push REALLY HARD to get it through the tire. (Unfortunately, with the first really cheap kit I tried, the tool broke while trying to push the plug in. Fortunately, I was just across the street from an auto parts store, and bought a better one. I never leave home without it.)
These days most shops won't plug a tire, and insist on removing the tire and patching it from the inside, for about $50...
The kits work MUCH better than injectable goo, in my experience.
But I believe them when they say don't patch a sidewall; way more flex than the tread, and less thickness to hold the plug.
Is this the Broke Genius Channel ???
You're joking, right?
RIDICULOUS- NEVER EVER EVER MAKE A DRYWALL HOLE BIGGER TO PATCH IT NEVER- ALWAYS PATCH IT AS SMALL AS POSSIBLE
AND BTW NEVER EVER CUT BACK TO STUDS JUST TO PATCH EITHER.. NEVER
rien de nouveau!!!! tout est déjà connu!!!!! tu viens de roumanie machin!!!!!!!!!!!!!!!!!!!!!!!
what a load of useless bollox !!!
C'est pour 99% de cette vidéo prendre les gens pour des cons et pour le 1% restant c'est NUL !
a Bunch of nonsense
Not sharp at all. This method is far from professional, stay away. The edgw must cut straight down with hardly a sound/
35 MINUTES & 56 SECONDS ⏲OF SOME VERY GREAT IDEAS. IT'S JUST TOO BAD THAT I'M NOT INTELLIGENT ENOUGH TO UNDERSTAND A LOT OF THEM. I REALLY WISH THAT YOU WOULD ADD SOME AUDIO, & TAKE THE TIME TO EXPLAIN EXACTLY WHAT'S GOING ON & WHY, SO THAT DUMMIES LIKE ME 🐒COULD GET THE JIST OF WHAT YOU'RE DOING, & HOPING TO ACCOMPLISH, BY DOING IT. BUT THANKS FOR ALL OF THE IDEAS THAT I DID UNDERSTAND. 🏆THEY ARE GOING TO BE VERY USEFUL TO ME IN THE FUTURE. 📆🤖 PLEASE KEEP ON POSTING THE GOOD WORK & ALL OF THE GREAT IDEAS. 👍
.
Riparate da soli le gomme, mi raccomando,il mondo ha bisogno di spazio
Mercy, stop with the stupid music.
0/10
Да у иностранцев новое то что мы в России давно вы...али.😅😂
Видео 7 заначка туалетной бумаги.
good morning,
Could you please stop inverting your videos when you publish them, because everything is upside down, the inscriptions and the screwdrivers that unscrew to screw and vice versa!
It's a real pain!
Hallo!
Könnten Sie bitte aufhören, Ihre Videos umzudrehen, wenn Sie sie veröffentlichen, denn alles steht auf dem Kopf, die Beschriftung und die Schraubendreher, die man aufschrauben muss, um zu schrauben und umgekehrt!
Das ist wirklich mühsam!
Hola,
Por favor, podrías dejar de invertir tus vídeos cuando los publicas, porque todo sale al revés, ¡las inscripciones y los destornilladores que se desenroscan para enroscarse y viceversa!
¡Es realmente molesto!
Salve,
Potreste per favore smettere di invertire i vostri video quando li pubblicate, perché tutto è capovolto, le scritte e i cacciaviti che si svitano per avvitarsi e viceversa!
È davvero fastidioso!
Здравствуйте,
Не могли бы вы перестать инвертировать ваши видео при публикации, а то все вверх ногами, и надписи, и отвертки, которые откручиваются, чтобы закрутить и наоборот!
Это очень раздражает!
안녕하세요,
동영상을 게시할 때 모든 것이 거꾸로 되어 있고, 비문과 나사를 풀어서 나사를 조이는 드라이버가 거꾸로 되어 있기 때문에 동영상을 거꾸로 게시하는 것을 중단해 주시겠어요?
정말 짜증나요!
Helló,
Légyszi ne fordítsd meg a videóidat, amikor közzéteszed őket, mert minden fejjel lefelé van, a feliratok és a csavarhúzók, amelyek kicsavarodnak, hogy becsavarodjanak és fordítva!
Ez nagyon idegesítő!
Bonjour,
Pourriez-vous arrêter d'inverser vos vidéos lorsque vous les publiez, car tout est à l'envers, les inscriptions et les tournevis qui se dévissent pour visser et vice versa !
C'est vraiment pénible !
I can’t stand the constant finger wagging and thumbs up bullshit