Hello Mr. Electron, i saw the entire video, thank you for showing the prank part, ive tested the first part. I saw it is not working. Thank you for revealing it in end
doesnt make sense. The green belt does not have enough power of friction to not slip without moving the flywheels weight + spring that pulls it. The green drive belt is a simple string, real drive belts for wheel this big need to be stronger and larger to obercome its wright
I have to agree the generator is actually a motor with a battery inside the frame. Proof to backup my conclusion is at 2:18 of the video pause and look at the top left of the screen you will see wires running into the frame. Thus it is high probable that this is powering the motor or “generator” that in turn the device.
This was pretty informative video the system has to have an external source using a flywheel generator on to another fly wheel yes the flywall generator keeps the motion going that's how this is working I like that idea it is actually feasible to do that and it's small amounts of power can produce very efficiently without the use of a gas powered generator so in a sense it is not a perpetual motion machine because you need an external source like a flywheel generator to produce it in the generator produces Is the power to rotate the Spring Spring fly wheel which is giving you the ability to run the flywheel generator to produce power it is a very simple process folks it is not a perpetual motion machine like he says
@@josephgraham1636 l would agree with you there is no such thing as perpetual motion.The nearest thing to perpetual motion is probably the Beverly clock Whichhas been running for now for 164 years and has never been wound in all that time however it is believed by the scientists it too will stop!! WHEN !! it is a matter of speculation but iIT WILL STOP in the meantime if you are ever in New Zealand it is worthy of a visit before it STOPS
The thing that you all are not considering is the begining amount of energy that was applied to start the machine... That energy is basically divided up over the entire cycle... Therefore energy is not created or destroyed... So this does follow the laws of physics... All I can say is while you continue paying your high energy bills these young men won't be with this creation... There is absolutely no reason that this wouldn't work.... Good job
Seeing all the ones debunking and all the ones claiming to be real, all i can do is attempt my own build. Ill address the inadequacies as i go. No belts, no intermediate pullys. Direct drive shaft with motors at both ends, a hefty flywheel, bearings, a diode, and dpdt knife switches. If it doesnt work, itll be because the voltage output deminishes with every revolution despite the flywheel mass.
note: flywheel bearing/generator/rpm/wheel/diameter more energy generate. note: motor input 20 kilowatt to rotate flywheel then flywheel generate 40 kilowatt and 20 kilowatt motor input to rotate flywheel and 20 kilowatt other work use.
I like these videos. Always search where the power supply.😄 This time, I suppose, The electric engine with fake wires actually an electric engine with batteries.
Newtons first law. Energy cannot be created nor destroyed. So the mechanical energy you put in in newtons is all that will run the machine, with that inertia and then will run out slowly due to friction.
Is it possible to create perpetual motion using flywheels and spring systems that remain in motion indefinitely without external energy input? If so, how can the law of conservation of energy be overcome?
No, it is not possible. Springs are like batteries they store energy. And just like a battery you can only get as much energy out of them as you put in. So when the machine is turning, the energy input from the spring contracting is being transferred to the spring that is expanding so there is no net gain the springs cancel each other out. There's a reason that you don't see videos of these machines running for hours on end and uncut.
Law of energy conservation was formulated by scientists, it's not a "law" but rather a relatively reliable model, like in 99% of cases considered in commercial applications it stands.
Yes, a spring machine with a flywheel can work, and the concept is physically sound, depending on the specific setup and application. Here’s how it typically functions:Spring Energy Storage: A spring can store mechanical energy when it is compressed or stretched. The amount of energy stored in the spring is proportional to the square of the displacement from its equilibrium position, based on Hooke's Law:[ E = \frac{1}{2} k x^2 ] where ( k ) is the spring constant and ( x ) is the displacement.Flywheel as Energy Buffer: A flywheel stores rotational energy. When the spring releases its stored energy, it can cause the flywheel to rotate. The energy transferred to the flywheel is proportional to its rotational inertia and the square of its angular velocity:[ E = \frac{1}{2} I \omega^2 ] where ( I ) is the moment of inertia of the flywheel and ( \omega ) is the angular velocity.Smooth Energy Release: The flywheel's inertia helps smooth out the release of energy from the spring. While a spring on its own might release energy quickly, causing sharp bursts of motion, a flywheel ensures the energy is released more steadily and gradually by resisting sudden changes in rotational speed.Practical Uses: Systems like this are used in mechanical watches (where a wound spring powers the motion and a flywheel or balance wheel regulates it) or in various mechanical devices requiring energy storage and regulated release.In summary, this setup works by converting the potential energy stored in the spring into rotational energy in the flywheel, which helps to regulate and smooth the energy release. Whether it works "true" depends on the specific design and intended function, but the underlying physics are sound.
It's weird how many comments cannot understand the energy stored and released in the springs. I don't think it will work forever because eventually the springs will weaken. For people in poor countries it's not a big deal to have to spin a wheel every few days or a week.
Add a self charging battery and a small motor to occasionally push, when with time the flywheel looses momentum over time. Making it energy efficient and self sustaining. The flywheel can only store energy over a limited duration without occasional push right?
Very good project but can you sell Energy Flywheel Kits to customers? Can you sell better version or upgraded version. I would prefer having this type of energy device that having Solar panels. It is well made , portable, perpetual and looks amazing . How much would this cost? 😎 ❤ 👍👍👁👁
as for the frankness, thanks for you. but to think you have simply used high friction bearings, it won't function, but if you use nested bearing or non - greased bearing, the friction from bearing can be over come using the momentum of flywheel, but even with the setting i said, it can't work for more than an hour.
I see lots of friction in this thing.. there has to be an energy source equal and opposite reaction are inviolateable. It is easy to pull this kind of trick while sitting under a high tensile power line. Tesla did this with some very high powered transformers. Lights burning moters spinning with the right rigging you can even boil water. And yes you can even eletroçute you're self doing this with just a few feet of wire. This is why we have a 10 foot distance restriction on high power electrical wires. And litning jumps for miles...
At the 2:17 mark pause it and look bottom left below the white housing . You can see a red wire coming out of a hole in the frame into the "generator " . If your gonna scam at least be good at it .
I appreciate you doing a 'test' that is better than others, since it has three springs in a triangle. - However, I am still waiting for an 'even better' test, with _seven springs,_ since it results in an imprecise division, maybe this raises some "hopes"!
Wouldn't dismiss this cool device all together, there may be a way to correct the problem with this tension converted into torque x 3 principle of operation. Need to id x factors in relation to downgrading to a zero force.
I realse my teaching lied to me and i am sorry for the west THAT XANT REALIZE THAT THAT TO HAVE RESPECT FOR THE INFORMATION TGAT IS SHOWN HERE THANK YOU FOR BEING CLEAR
At abou the 11 minute mark you can clearly see the deception here. The motor is fiddled with and it starts running by itself, but notice the belt tension on one side with rotation direction proving that the so called unconnected motor is driving the large pully and not the other way round.
He had given the fly wheel an initial velocity. If I am right, he has given the fly a push (which is scientifically force) and as a result, the fly wheel had potential energy and as we all know that potential energy gets convorted into kinetic energy (rotational movement in this case which is also a form of kinetic energy) amd therefore the wheel gets rotated Albert himself said that reaching light speed is impossible as it would require infinite energy which is impossible and this guy says that his mechanism would produce infinite energy.🤣🤣🤣🤣🤣🤣🤣
Don't worry you'll be recommended for'Nobel prize in physics, ' by youtubers since it will save the earth from any green house gases all cars hence forth will come to markets for sale with this'tech😅
spinning at a constant speed with a heavy flywheel and with the output of the generator open very little breaking force and the springs have little to no acceleration effect on the flywheel , still keep trying, maybe someday you will actually make a breakthrough should you find some true method of converting gravity to electricity or some such thing
the hardest part about making an overunity device is hiding the battery, let's see it without the motor attached, a treadmill motor will run at pretty low voltage as it is dc, that would be about the speed you could acheive from 4.2 volts from a single lipo/lithium ion edit: guess so, thanks for not leading people on in the end
Correct but i use 35v dc instead of the 4.2v dc. The speed is slow because the motor is rated at 220v + the gear ratio of the motor pulley and the flywheel. Its a scam exposed video.
As he's going around with the video you can clearly see a red and black wire entering the frame you see a little burn spot Right at the back of the treadmill motor there's a hole there and you can see a black and red wire Inside the frame So yeah I call BS
You increased by 1 not 3 … with math like that I’m more than concerned with your math that says it will run forever… the bike wheel machine runs around 2 years before it needs something done with it. You are going to need way more than that video my friend
@@MayhamHeaventhis is not impossible to make it but the problem is mafias who never want people to get free energy source because how they will sale their trillions of dollars generators and engines, Same as thousands of years ago human being never imagine he can make the highest speed rockets and he can travel to the other planets but gradually human being learned and discovered it, so even this video is real or fake but perpetual motion is possible and working because I am 50 years experienced in innovations and inventions, he used the wrong angles and timing.
Have you studied physics or thermodynamics or do you understand the principles or are you aware that they exist??You cannot create or destroy energy this machine will not work overunity does not work
@@jesusislordforever5518 l don't have to prove that it does.not work because l have asked the maker of this preposterous contraption to define his circuit he refuses to do so because it is a fake project and science says IT CANNOT WORK.in other words you cannot create energy surely you understand this simple analogy
@@concyprus4895 you all repeat the same things. like zombies. ( you have no guilty. The Goal of Universitiy is create ignorant people ) Before you have to study Maxwell and Faraday and maybe after that you will can understand
These motor seem to be popping up all over UA-cam..by the look of this one he has use to small springs and the crank Shaft is not well made..I think if he had worked the engineering he may have got better Result ...oh and welding bearings like that is not such a good idea ..I will be Building one..
Hindi Version : ua-cam.com/video/yXOPDTFgOsk/v-deo.html
English Channel : ua-cam.com/video/GdDBQEixzgQ/v-deo.htmlsi=RnH8Z2gpoATeWUAz
Hello Mr. Electron, i saw the entire video, thank you for showing the prank part, ive tested the first part. I saw it is not working. Thank you for revealing it in end
THERE SHOULD BE A LAW THAT DE-FUND SCAMMER LIKE THESE ..... SAME IN REGULAR LIFE YOU GET ARRESTED FOR ANY CON JOB SO WHY NOT IN UA-cam
SCAM.
Remove the green drive belt and the wheel will not turn because the trick is in the "generator" : motor + battery.
doesnt make sense. The green belt does not have enough power of friction to not slip without moving the flywheels weight + spring that pulls it. The green drive belt is a simple string, real drive belts for wheel this big need to be stronger and larger to obercome its wright
@@petrolom1889 I do not agree : the belt has a good diameter and is tight.
And this is the only way to mnake the machine turn.
@@regisvoiclair I know :D
I have to agree the generator is actually a motor with a battery inside the frame. Proof to backup my conclusion is at 2:18 of the video pause and look at the top left of the screen you will see wires running into the frame. Thus it is high probable that this is powering the motor or “generator” that in turn the device.
Why would you say that????? Where is your evidence????
2:12 the vires from the hole in frame is connected to the "generator" 👌-> its powered by motor
Yes, 2 wires going into the frame, and earlier when he moves it, he rotated it with that corner as the axis, so wires can be going to a power source
This was pretty informative video the system has to have an external source using a flywheel generator on to another fly wheel yes the flywall generator keeps the motion going that's how this is working I like that idea it is actually feasible to do that and it's small amounts of power can produce very efficiently without the use of a gas powered generator so in a sense it is not a perpetual motion machine because you need an external source like a flywheel generator to produce it in the generator produces Is the power to rotate the Spring Spring fly wheel which is giving you the ability to run the flywheel generator to produce power it is a very simple process folks it is not a perpetual motion machine like he says
It's Garbage.
@@josephgraham1636 l would agree with you there is no such thing as perpetual motion.The nearest thing to perpetual motion is probably the Beverly clock Whichhas been running for now for 164 years and has never been wound in all that time however it is believed by the scientists it too will stop!! WHEN !! it is a matter of speculation but iIT WILL STOP in the meantime if you are ever in New Zealand it is worthy of a visit before it STOPS
Stop the video at 2:17 and look under the "generator" you will see a red and black wire...hahaha got ya!
You definitely got me. I looked.
i couldnt see it ,, your on drugs
Really remove the belt and let's see if it will work.the hard work is hiding the batteries inside the generator.
Isto sam napravio sa federima radi bez ikakve energije
Ler's see😂@@banepejcic2241
There is someone out there now building one of these😂…Newtons law of springy springs.
The thing that you all are not considering is the begining amount of energy that was applied to start the machine... That energy is basically divided up over the entire cycle... Therefore energy is not created or destroyed... So this does follow the laws of physics... All I can say is while you continue paying your high energy bills these young men won't be with this creation... There is absolutely no reason that this wouldn't work.... Good job
Seeing all the ones debunking and all the ones claiming to be real, all i can do is attempt my own build. Ill address the inadequacies as i go. No belts, no intermediate pullys. Direct drive shaft with motors at both ends, a hefty flywheel, bearings, a diode, and dpdt knife switches. If it doesnt work, itll be because the voltage output deminishes with every revolution despite the flywheel mass.
Do it with and without the motor
Save your time it won't work.
note: flywheel bearing/generator/rpm/wheel/diameter more energy generate.
note: motor input 20 kilowatt to rotate flywheel then flywheel generate 40 kilowatt and 20 kilowatt motor input to rotate flywheel and 20 kilowatt other work use.
I like these videos.
Always search where the power supply.😄
This time, I suppose, The electric engine with fake wires actually an electric engine with batteries.
Could you please remove the generator motor from the flywheel?
Newtons first law. Energy cannot be created nor destroyed. So the mechanical energy you put in in newtons is all that will run the machine, with that inertia and then will run out slowly due to friction.
The springs heat up and suck energy as well as mechanical friction. It's a flywheel with decorations.
Is it possible to create perpetual motion using flywheels and spring systems that remain in motion indefinitely without external energy input? If so, how can the law of conservation of energy be overcome?
No, it is not possible. Springs are like batteries they store energy. And just like a battery you can only get as much energy out of them as you put in. So when the machine is turning, the energy input from the spring contracting is being transferred to the spring that is expanding so there is no net gain the springs cancel each other out. There's a reason that you don't see videos of these machines running for hours on end and uncut.
Law of energy conservation was formulated by scientists, it's not a "law" but rather a relatively reliable model, like in 99% of cases considered in commercial applications it stands.
Yes, a spring machine with a flywheel can work, and the concept is physically sound, depending on the specific setup and application. Here’s how it typically functions:Spring Energy Storage: A spring can store mechanical energy when it is compressed or stretched. The amount of energy stored in the spring is proportional to the square of the displacement from its equilibrium position, based on Hooke's Law:[ E = \frac{1}{2} k x^2 ] where ( k ) is the spring constant and ( x ) is the displacement.Flywheel as Energy Buffer: A flywheel stores rotational energy. When the spring releases its stored energy, it can cause the flywheel to rotate. The energy transferred to the flywheel is proportional to its rotational inertia and the square of its angular velocity:[ E = \frac{1}{2} I \omega^2 ] where ( I ) is the moment of inertia of the flywheel and ( \omega ) is the angular velocity.Smooth Energy Release: The flywheel's inertia helps smooth out the release of energy from the spring. While a spring on its own might release energy quickly, causing sharp bursts of motion, a flywheel ensures the energy is released more steadily and gradually by resisting sudden changes in rotational speed.Practical Uses: Systems like this are used in mechanical watches (where a wound spring powers the motion and a flywheel or balance wheel regulates it) or in various mechanical devices requiring energy storage and regulated release.In summary, this setup works by converting the potential energy stored in the spring into rotational energy in the flywheel, which helps to regulate and smooth the energy release. Whether it works "true" depends on the specific design and intended function, but the underlying physics are sound.
Thank you for your comment. I'm so tired of the naysayers. I just know this works for some reason.
God Bless!!!
It's weird how many comments cannot understand the energy stored and released in the springs. I don't think it will work forever because eventually the springs will weaken. For people in poor countries it's not a big deal to have to spin a wheel every few days or a week.
One spring constantly pulling two springs in a loop will never work. Think of it this way. Two springs are stronger than one spring.
Friction is your enemy. Even with good lubrication there is friction, it degrades power.
Add a self charging battery and a small motor to occasionally push, when with time the flywheel looses momentum over time. Making it energy efficient and self sustaining. The flywheel can only store energy over a limited duration without occasional push right?
He Comes Clean at The End of The Video ! The Power is in The Motor Itself Pay Attention People
People haste to comment without knowing the full story. They are not patient at all yet they want to have an opinion.
Очень хорошее видео! 👍👍👍👍👍 Всё показал, рассказал как есть.
Благодарю!
multumesc in primul rind ca esti un om cinstit . si eu ma ocup cu asa ceva dar nu postez . mult succes in continuare
I've been using this method for years to power my whole house - no electricity bill for me!
So you are on DC voltage ? This turning so slow , not getting full charge voltage / amperage ?
@@RobertFulton-o9j You can convert from DC to AC no problem.
Do you have plans
Battery's
In frame? Power station operator 9 years. Nothing for nothing .😂😂😂.
Если вы действительно сделали этот двигатель, скажите пожалуйста, как сделать его так чтобы он работал, как настроить пружины.
If only you had a water wheel and a stream. That is the closest thing to free energy I can think of.
Simply and efficient 👍
Batterys in frame.
Very good project but can you sell Energy Flywheel Kits to customers? Can you sell better version or upgraded version. I would prefer having this type of energy device that having Solar panels. It is well made , portable, perpetual and looks amazing . How much would this cost? 😎 ❤ 👍👍👁👁
Yes I think you should of used bigger spring soils...
Does it turn faster with the other armature hooked up with three springs
rakesh, your cousin told me this is fake
Молодец что сказал правду!
Cut the green belt then champion, ill wait..
Love it - you had me fooled - I thought you meant it!
Pretty sure this honest guy called me last week trying to get my credit card details.
I think I'd add more springs and try to make it run harder
This wouldn't help at all. N times zero is still zero. Springs are not a source of energy.
All good until you apply conservation of energy principles. It Works good until you add a load.
You are a genius ❤
as for the frankness, thanks for you. but to think you have simply used high friction bearings, it won't function, but if you use nested bearing or non - greased bearing, the friction from bearing can be over come using the momentum of flywheel, but even with the setting i said, it can't work for more than an hour.
there's a secret battery inside the motor try to remove the green belt its a real understand!
I see lots of friction in this thing.. there has to be an energy source equal and opposite reaction are inviolateable.
It is easy to pull this kind of trick while sitting under a high tensile power line. Tesla did this with some very high powered transformers.
Lights burning moters spinning with the right rigging you can even boil water.
And yes you can even eletroçute you're self doing this with just a few feet of wire.
This is why we have a 10 foot distance restriction on high power electrical wires.
And litning jumps for miles...
At the 2:17 mark pause it and look bottom left below the white housing . You can see a red wire coming out of a hole in the frame into the "generator " .
If your gonna scam at least be good at it .
I appreciate you doing a 'test' that is better than others, since it has three springs in a triangle.
- However, I am still waiting for an 'even better' test, with _seven springs,_ since it results in an imprecise division, maybe this raises some "hopes"!
Wouldn't dismiss this cool device all together, there may be a way to correct the problem with this tension converted into torque x 3 principle of operation. Need to id x factors in relation to downgrading to a zero force.
Microsoft's in cooperation with IRS made this.
I realse my teaching lied to me and i am sorry for the west THAT XANT REALIZE THAT THAT TO HAVE RESPECT FOR THE INFORMATION TGAT IS SHOWN HERE THANK YOU FOR BEING CLEAR
I think if the springs were tighter/shorter there would be greater force and the flywheel would drive it past the point of failure.
At abou the 11 minute mark you can clearly see the deception here. The motor is fiddled with and it starts running by itself, but notice the belt tension on one side with rotation direction proving that the so called unconnected motor is driving the large pully and not the other way round.
Is it possible to have a Mutual energy Generator? KINETIC and POTENTIAL to construct Perpetual Motion thereby Achieving Permanent dynamism.
A nice trick, the energy source is the small dc generator (battery operated motor) with speed controller. thank you for exposing.
Why are you connecting the motor to the flywheel with a belt first? 2)You are regulating the motor speed. So it may be a battery operated motor.
Come on dude, we know it's not possible, we're all looking for the battery
Ok so this DOESNT work?
He had given the fly wheel an initial velocity. If I am right, he has given the fly a push (which is scientifically force) and as a result, the fly wheel had potential energy and as we all know that potential energy gets convorted into kinetic energy (rotational movement in this case which is also a form of kinetic energy) amd therefore the wheel gets rotated
Albert himself said that reaching light speed is impossible as it would require infinite energy which is impossible and this guy says that his mechanism would produce infinite energy.🤣🤣🤣🤣🤣🤣🤣
Don't worry you'll be recommended for'Nobel prize in physics, ' by youtubers since it will save the earth from any green house gases all cars hence forth will come to markets for sale with this'tech😅
Take that belt off and let's see how long it runs
Yep there is almost hidden wire in the frame under the alt/motor at 2.21
The tension force of the springs is not the same.
The only perpetual motion that exist is the earth spinning on it's axis
It's not perpetual either . It will stopp one day too .
spinning at a constant speed with a heavy flywheel and with the output of the generator open very little breaking force and the springs have little to no acceleration effect on the flywheel , still keep trying, maybe someday you will actually make a breakthrough should you find some true method of converting gravity to electricity or some such thing
Some guys happiness is enjoying their foolishness creating free energy, its their freedom anyway
the hardest part about making an overunity device is hiding the battery, let's see it without the motor attached, a treadmill motor will run at pretty low voltage as it is dc, that would be about the speed you could acheive from 4.2 volts from a single lipo/lithium ion
edit: guess so, thanks for not leading people on in the end
Correct but i use 35v dc instead of the 4.2v dc. The speed is slow because the motor is rated at 220v + the gear ratio of the motor pulley and the flywheel. Its a scam exposed video.
Very lame and boring statement.
फेक
Fake
As he's going around with the video you can clearly see a red and black wire entering the frame you see a little burn spot Right at the back of the treadmill motor there's a hole there and you can see a black and red wire Inside the frame So yeah I call BS
Did it power your welder??
What kind of springs are used and where to buy?
Change the position of green belt need tire to be free for the gravitational weight durr.😂
Add 2 minutes and 17 seconds you can see the wires going to the battery under the motor
Well spotted
Thanks 👍 for your time today and your video is fantastic and keep doing your job.
remove the green belt theres inside the rotor
Take the belt off , it will stop. Why the mask operator.
Hola a todos cuanto tiempo tarda la bateria que tiene el motor por dentro ?
L O L who else is wearing crocs for welding
😂😂😂 half of Asia and the other half are barefoot 😅😅😊
Wasted almost 2 minutes watching this video before commenting about how much time I wasted watching this video.
I think the red flywheel is too big for those small springs. The springs need to be bigger and stronger or the flywheel smaller.
Nice welding for a 6 year old. LOL
Skip to 10:38 for the truth...
Ok bro you are now a good domas 😅😅🤣
모터를 부착하지말고 보여주시길 부탁드립니다
Remove the electric motor before testing. The motor could be the one powering the flywheel
You increased by 1 not 3 … with math like that I’m more than concerned with your math that says it will run forever… the bike wheel machine runs around 2 years before it needs something done with it. You are going to need way more than that video my friend
2:18 a red and black wire can be seen coming out of the steel tubing..lol not one of the fakes huh?
Maybe in outer space it work but here on earth no! Because of gravity
How so? Because i made one myself and it works just fine
Daca este corect fal si la alti care au nevoie de energie si totul se va multiplica in timp ca roata de car @@MayhamHeaven
@@MayhamHeaventhen where is the video !
@@MayhamHeaventhis is not impossible to make it but the problem is mafias who never want people to get free energy source because how they will sale their trillions of dollars generators and engines,
Same as thousands of years ago human being never imagine he can make the highest speed rockets and he can travel to the other planets but gradually human being learned and discovered it, so even this video is real or fake but perpetual motion is possible and working because I am 50 years experienced in innovations and inventions, he used the wrong angles and timing.
Now the sale
of Springs is increased
🤣
you should SELL kits and plans !
It's a scam exposed video....
Not perpuation because moving parts are there !!
By 2:45 in I already have observed a few telling signs that you are telling the truth. My gut feeling says your device does what you claim it does.
Scammers by day and scammers by night. LOL
The square frame NEEDS more stablity
I've seen people using this...
Have you studied physics or thermodynamics or do you understand the principles or are you aware that they exist??You cannot create or destroy energy this machine will not work overunity does not work
Why don't you prove that it doesn't work?
@@jesusislordforever5518 l don't have to prove that it does.not work because l have asked the maker of this preposterous contraption to define his circuit he refuses to do so because it is a fake project and science says IT CANNOT WORK.in other words you cannot create energy surely you understand this simple analogy
Free energy is possible and very easy but not it that way. Energy is eternal and can be get easily in hundreds of ways.
@@edo_ardo HOW EXPLAIN!!!! without breaking the rule of physics or thermodynamics??
@@concyprus4895 you all repeat the same things. like zombies. ( you have no guilty. The Goal of Universitiy is create ignorant people ) Before you have to study Maxwell and Faraday and maybe after that you will can understand
People are still trying to make these? It’s 2024, everyone should know better by now…
Different then the others. Mine is the 4 spring type grounded. Who would of thought. Cammed springs ''
These motor seem to be popping up all over UA-cam..by the look of this one he has use to small springs and the crank Shaft is not well made..I think if he had worked the engineering he may have got better Result ...oh and welding bearings like that is not such a good idea ..I will be Building one..
I'll take things that did not happen for $500Alex
LIKE EMBEZZLEMENT
ok.... now add aload....
It doesn’t have to be perpetual movement. It doesn’t have to be efficient. It just needs to be efficient enough to be sufficient.😊
Sorry you must have never heard of when, you transfer energy, you lose energy, this perpetual motion machine is impossible 😂
Come clean pal it don't work , take the belt off
IF you should do 120ံ crank fhuft
Like car 3 piston system
it got un ablestop power .
Is real or fake pls comment
Fake
Fake
A LEI DA CONSERVAÇÃO da energia destrói esse movimento contínuo. Isso não existe
Ispar kuch chala kar dikha bhai mujhe bhi ye banana hai😮