I am only recently following your videos which are very informative, thanks for the clear explanations. For this circuit I want to know what power you need to provide for the resistors and potentiometers, thanks Zafer Pol, Belgium
12V girişi 24 V gibi değere yükseltebilir mi yoksa sadece giriş değerinden küçük gerilim mi çıkışta alınır ? Ek olarak 2 tane TIP35C paralel bağlansa çıkış max amper değeri artar mı? Teşekkürler
If the input voltage is constant, it is possible to use high voltage BTJ transistors.You can even use a mosfet, you can look at the examples on the channel.
It would be better if you tell us the voltage of the power supply, but it would also be a solution to make a regulated power supply with LM317 and reduce the voltage to 1.5 volts. add capacitors to input and output to filter out noise
السلام عليكم ورحمة الله وبركاته سلامي الئ العبقري ظافر ❤❤❤❤❤ م.. ملك الاكترونيات ماشاءالله دائره رهيبه وسلامي الئ محبي م.. ظافر وارجو من الجميع ان تدعو له بالصحة والعافية وان الرزق الكثير اللهم امين يارب العالمين وشكرا❤❤❤❤❤❤❤
سلام برادر خوبم مهندس ظفر عزیز ، من از کشور ایران شمارا دنبال میکنم ، خیلی به این مدار احتیاج دارم ، اما با ورودی ۳۱۰ ولت بعد از پل دیود و خازن صافی و بعد وارد این مدار بشود و امکان کنترل ولتاژ و امپر را داشته باشد ، از شما خواهش میکنم من را کمک کنید که باید چکار کنم ؟ خدا به تو دوست مهربان و استاد بزرگ عزت و سربلندی و طول عمر بدهد . ❤
Excellent Sir, we are so Great full for Engulfing Knowledges By You Sir.
I sincerely thank you for your wonderful comment and support.
Thanks very much for sharing
Thank you for your nice support and comment.
Thank you Dear Brother
Thank you
I am only recently following your videos which are very informative, thanks for the clear explanations.
For this circuit I want to know what power you need to provide for the resistors and potentiometers, thanks Zafer
Pol, Belgium
Super! Thank you very much!
I sincerely thank you for your comment and support.
Is it possible to adjust the current and voltage used when using CREE LEDs ?
Keren, salam dari Indonesia 🇮🇩🇮🇩
Salam dan cinta dari Indonesia
12V girişi 24 V gibi değere yükseltebilir mi yoksa sadece giriş değerinden küçük gerilim mi çıkışta alınır ? Ek olarak 2 tane TIP35C paralel bağlansa çıkış max amper değeri artar mı? Teşekkürler
Bro zafer Thank for sharing
Thank you for your comment and support.
Useful circuit .👍💚
thx my friend
Creative video, thanks :)
thx my friend
sir,I noticed that you didn't connect the multi-meter right when measuring current and I think that wrong
correct me if I am wrong
süper elinize sağlık ustam
çok teşekkür ederim kardeşim eksik olma seviliyorsun
Vc esta certo, somente a tensão foi verificanda, com queda em pouca carga, tudo bem que não vi que fonte foi utilizada para o teste.
Will keep, thumb up update when everything matches up. Nice idea 💡🙂 tho!
Teşekkürler. 👏👏👏
how to control a mosfet operating at 200-350v so that it opens in this range. voltage increase more open. Thank you very much for the tip.
Sir, in your opinion how best DC regulated power supply 0 volt to 70 volt 15amp can be made at home. Please help me with circuit diagram.
If the input voltage is constant, it is possible to use high voltage BTJ transistors.You can even use a mosfet, you can look at the examples on the channel.
SUPER 👍🏿👍🏿👍👍
thx my friend
Excellent work, the 10 Ohm resistor is 1whatt?
Yes
Hello, nice circuit, but why the voltage is still dropping even if you increased the current ?
When the current drawn exceeds the set value, the voltage will collapse to keep the current constant. batis power formula W=I.V
@@ZAFERYILDIZ52 ok. Thanks for the explanation.
Buyorumu görenler videoyu beğensin😊😊
teşekkürler kardeşim
Dear Zafer, than you! If current is on minimum, does short cut destroy circuit?
Yes, if the short circuit input current is high, it will destroy the transistor. However, if the current is at minimum it will not cause any harm.
@@ZAFERYILDIZ52 Thanks Zafer !
Dear how to make 1.5volt power supply to use hearing aid through electric, thanks your videos all very useful please reply
It would be better if you tell us the voltage of the power supply, but it would also be a solution to make a regulated power supply with LM317 and reduce the voltage to 1.5 volts. add capacitors to input and output to filter out noise
Ellerine saglik ustam lm317 ile yapip calistiramadiklarimdan sonra ilac gibi geldi
peh hassas degildir ama iş görür
@@ZAFERYILDIZ52 ne zaman yapsam potans son konumda yanıyor be ustam
amper ve volt da max. seviyeler ne kadar?
maksimum 10 amper ama 12 voltu geçmemek kaydı ile kullanılan transistöre göre bu deger değişecektir
Mr zafer yildiz What about the amperage control .
It will not be very sensitive. An application that is useful for learning but based on a single transistor.
Selamın aleyküm 7905 5v veriyor bu 5 i 3v nasil ederim kaclik direnc lazim
dirençle düşmez ama çıkışa 3 tane 1n4007 seri ekleyin çıkıştan 2,9 volt sabit alabilirsiniz
السلام عليكم ورحمة الله وبركاته سلامي الئ العبقري ظافر ❤❤❤❤❤ م.. ملك الاكترونيات ماشاءالله دائره رهيبه وسلامي الئ محبي م.. ظافر وارجو من الجميع ان تدعو له بالصحة والعافية وان الرزق الكثير اللهم امين يارب العالمين وشكرا❤❤❤❤❤❤❤
q tendra q ver dios con la electrónica ?? esto es real, dios NO
أمين
Super zafer sir I am ur fan excellent work I have small dought how much watt is 10 ohm.. Thank u Boss🎉❤
10 ohm 2 wat brother and thank you for your comment and support, the circuit is not as sensitive as LM317 but it will work.
I am very happy with your reply and thank you Boss👑
Good
? how is power source voitage Vcc about DC20V? ?
I didn't understand the question clearly
Благодаря!❤ Бог си!❤
😊
Благодаря ви за коментара и подкрепата.
There's an error in the diagram again!
The negative connection between R2 and RP1 is not shown....😀
It has been noticed, the error will be fixed and thank you for the information.
👍👋❤️❤️👋👍
👉❤❤👈
süper
teşekkürler kardeşim
👍👍👍👍
👉❤👈
Input voltage?
30v
Devre şeması yanlış. Iyi bir hatayi bul, bulmaca sorusu olurdu. Ayrıca montaj da yanliş; watlı direnç emiter'de ki yüke seri gelmesi gerekiyor..
şema düzeltilecek montaj doğru
سلام برادر خوبم مهندس ظفر عزیز ، من از کشور ایران شمارا دنبال میکنم ، خیلی به این مدار احتیاج دارم ، اما با ورودی ۳۱۰ ولت بعد از پل دیود و خازن صافی و بعد وارد این مدار بشود و امکان کنترل ولتاژ و امپر را داشته باشد ، از شما خواهش میکنم من را کمک کنید که باید چکار کنم ؟ خدا به تو دوست مهربان و استاد بزرگ عزت و سربلندی و طول عمر بدهد . ❤
310 ولت برای این مدار خیلی زیاد و خطرناک است
Салям алекум Зафер можно схему хорошую и коректно работающую часто смотрю Ваши видео
24 volt serice connection dio gram
电路图是错误的
👌 已注意到并将予以修复
Current control is not working properly. Useless circuit
It works but the efficiency will be low
Diagram is wrong.
👌