good stuff. Might want to discuss about making sure you always order extra tile. Being 1 or 2 short and then you go to buy another box and it either doesn't exist anymore or the color is slightly different. (plus you always want a few extra to sit in the attic for the next owner to find 30 years later. :-) )
I’ve always bought 10% over, for some reason because my brain doesn’t account for areas that give you 2 cuts from 1 tile I always end up with excessive overage
This has been the single most informative and helpful tiling series I have ever watched. I very grateful for all your advice and willingness to instruct.
I agree completely and wanted to add that the detail comes through well due to the sincerity of the presentation and passion that Paul brings to it. Well done guys.
Such an awesome series! As a fellow UA-camr I have just one recommendation - maybe put all of these videos in a playlist so they're easier to find. Took me a bit to sift through and find each new step in the series because of the other vids in between.
I've been a diy, for 40 years, and watching this video I learned something. cool. There was a time, before computers, before cell phones, where people helped each other on their projects, and that was cool, since you could know 90%, if you help knew something too. Since that disappeared, over the years, it's nice to learn something from the videos.
I've been in the trades for over 50 years (Framing, Finish and custom oak stair builder). You guys are really awesome. I love the videos and I love that you are taking the time to teach generations of DIY'ers ...Kudos guys.
Professional tile setter for 20 years. Couple of points. 1. As mentioned by others the top tile on the left wall should be two tiles to match the pattern, although I suspect with your attention to detail and perfectionism, the next video will be you realizing you oopsied. 2. When doing the layout, if you are using a pure white tile, the thin strip of the tile at the top will disappear visually speaking, when it is grouted with white grout. With a patterned tile perhaps not so much. That isn't to say you shouldn't have done your layout this way, as it gave you full tiles at the top and bottom of the niche. The expression I have come up with is that tile setters are trying to create the "veneer of perfection" (all you Frasier fans should take a drink at this moment!) You can't create perfect but you want the observers eyes to land where you want them to land and not see the fact that the tiles are not full tile at every wall which would be true perfection. (in 20 years that has only happened once for me). Having full tile at the top and bottom of the niche draws the eyes. Perfect. 3. When I tile with kerdi, I scratch coat the wall and trowel the notches onto the back of the tile. I find it is less messy. I scratch coat the whole wall all at once, even if it dries, thin set adheres to itself really well. I trowel the thinset on the back of the tiles out from the center so that the air still can escape out the grooves. After some practice I can spin up to a 2'x2' tile on my hand (like a pizza) and trowel with the other, or place on clean water bucket and trowel away. 4. When cutting out the square for the tap hardware, start on the face side. You may need to get a better grinder wheel that cuts cleaner. I have found some of the best wheels at rental stores. $20 Canadian, can't remember the brand and the name has worn off the wheel. Tiled 50 bathrooms with 1 grinder wheel and a tile cutter like yours. As well I use a wet diamond pad, about the size of a drywall pad. Again I think they are in the $20 range. I would go to a tiling supply store if you don't already. They should have them. They are relatively inexpensive and do the same as your file to smooth the edges, but if you ever get into mitering corners they help a great deal. As well you can use them to clean cured mud off of your tools to get them back to shiny. 5. Ideally you want the wall tile to land on your sill but with the stone slab that makes the point moot. 6. I have only ever had one hole saw to do the shower head pipe and it is about 1 1/4", Again I don't think too expensive at a tiling supplies store. 7. Keep up the great work. I have learned a lot of fantastic info from you about other aspects of construction. Your skills are what got me to start watching your channel, your humility keeps me watching! Feel free to pick my brain if you want on tiling questions
Super appreciate that 👊👍. I noticed the top tile when we did the outtro 😡. Last tile…. Not thinking it through…. Working till 7pm… all the excuses right 👊👍
I like that you show the tips and tricks for people who have never done this before at all. Too many youtube videos assume a much greater level of experience in construction than a lot of us actually have...
Wow. I've watched a number of very good videos on tiling, but you are so thorough, showing, discussing and explaining every aspect of the job, I feel like I'm there with you learning as you do it. Combine that with your knowledge, expert technique and attention to details to all aspect of the work/job is incredible. Very glad I discovered your channel.
Had to pause the video and write this comment. Of course I’m going to learn something on this video. You’re one of the only ones on here that really explains technique the why’s of everything you do. You make it easy to follow and entertaining as well.
If there are any DIYers out there who skipped to this video, without watching the others, you will miss the most important aspect of tiling, and that is prep. Paul’s tile goes on so nicely because he spent so long making sure he had a flat square and plumb surface to attach it to.
In my early years I learned this the hard way. Rushed the set up because I thought I was good enough to fix/hide/cheat any problems I would run into. One client, one shower changed that way of thinking. I'll never forget it. That day I learned a lesson and went from pro to expert at that moment when I knew i'd always spend more time prepping than laying from that job on.
@@ProToolsApproved Yep. Tile stobbornly refuses to bend! Great that you got the lesson, though. As I’ve gotten older, and I am almost 56 now, I have come to regard these as “kick in the ass” moments, which I recognize faster, learn the lesson, and welcome the next one.
Well you can prep all you want like my husband did and then when the tiler's came in they made a worse mess than what he'd already tore out. There was no waterproofing before and they still didn't waterproof it in the new installation. There is no grout in the walls they used clear silicone with white porcelain...? I have two standing 1/8 inch deep puddles 4 inches away from the drain hole..?? The uprights for the shower slider doors half on porcelain half on plasterboard. The tiles on the wall one foot by 2 ft some hang an eighth of an inch out over the tile below and others are the opposite. And up to half inch gap in bottom corner tile just filled in with silicone. The list goes on. Now my husband's a disabled veteran that's why it took him so long to tear a small 6x9 bathroom apart, and it was supposed to be a present for him. Bottom line is... it must be all tour back out and redone floor to ceiling. The help he got was from family who has been building homes for three generations. So much for family and all that love. You should see the let down in his eyes,.. it's heartbreaking.
Your the first tile person that I see using straight collapsing channels of thinset. Almost never see anyone doing tile the right way. When I tell people about trapped air I usually show them by dropping a coin on their tile floor using the hollow sound to show voids. Really appreciate the professionalism.
I love your videos. I'm learning as fast as I can, tiling a master bath walk-in shower with 12 x 24 tiles, and pebble floor, now. One thing that I learned that you don't have in there is to put the leveling system Ts behind the ledger strips so that the bottom tiles can be leveled when they are installed. Don't forget to lower your ledger strips the appropriate amount to make up for the additional height that the Ts add to the ledger. Also, be sure that you put the Ts in all of the correct places for the tiles to be installed above and below.
The most impressive skill I've seen you perform is to do such a good job without metric measurements. That's probably the most impressive thing about America in general. Well done. Keep it coming.
I personally get a little laugh because when I was a contractor, especially with tile, I never got to go home as clean as you guys lol. Great work and very informative video. Thanks for sharing the art and precision that goes into these jobs
Your a great instructor, as far as cutting the holes for the fixtures, I used 15.00 bit, what it was was a Dremel tile bit with a rotozip tool. I cut 5 holes and it's pretty much done for. But for the price I can't complain. It was worth it's weight in gold..
I don't think I'll ever try this stuff, myself, but I love seeing your work, your method for teaching, and your explanation of the full process PRIOR to starting it. I think a lot of DIY channels could learn a thing or two from your presentation!
My last house flip was 16 years ago. Your video is a nice refresher to get my brain into shape before I tackle a bathroom demo and rebuild. So many original crimes by the builder! I like your "Story Pole" 2x4. I'll look for your other videos.
Number one tip I've got from this series is cleaning the edges with a margin trowel before installing each tile. Seems obvious now, but it never occurred to me when I did my shower. Spent a *lot* of time cleaning out the joints before grouting. 😞 Great content as always, gents. Keep up the good work!
Set tile with my dad back in the late 70's and mid 80's. Thought I knew a few things but you took it to another level!! Thank you for the insight and tips! Outstanding!
Good idea. Personally I always assumed the reason tile companies sell tiles with dimensions slightly less than 1 or 2 foot is to compel us to buy accent strips. ;)
I would probably just open the grout lines like 1/16? to keep a full tile at the bottom and eliminate the sliver. Or possible try to factor that in when determining the slope of the pan. There’s so much to think about and everyone has different taste. That’s what I love about tiling.
Another option which I like is to have a horizontal strip mid wall of a contrasting title that's 3,4,6". That allows me to always have a full tile at the bottom and cut a little off the tile at the ceiling. Plus the contrasting strip is always going to be seen as a more custom job, higher value.
S.P., I love how y'all are really zero'ing in on anticipating questions. Example, the leger, exactly when I was thinking about the screws holing the ledger board, y'all said you'll patch them with a little curdy as you do the bottom course. Very cool! Got to add, once of the best shower tiling videos I've seen. One of your best as well, IMSHO. Very inspiring, considering I've got a master suite I really need to get to. Thank you again.
@@moneyfornothing3264 Distance and Money. I live in N. Texas, and budget constraints push to DIY. FWIW, I'be already built furniture, cabinets, electrical, some plumbing, and have done siding on the house. Tiling and some of the finer finishing things are left to be personally explored. But I will get there. SP has really helped.
I’ve owned rental’s for over 30 years and mostly did my own work. I had to learn how to do everything myself, because I would pay someone to do it and then have to redo it. I’m retired now and I don’t have anymore rentals so I don’t have to learn this stuff anymore but I find myself addicted to your videos. I love all of your tips and tricks. I especially love your tip for hanging drywall on the ceiling. I highly recommend anyone that hasn’t seen it to go back and watch it.
You could use painters tape to lay out the lines with the speed square on the front side of the tile. Then cut with the grinder from the front side and inside the tape line. The tape won't mark the tile and it helps prevent too many chips.
Thank you so much. Had no idea I could get metal edging trim, last time I did this job 20 years ago I just used plastic cove trim. The metal looks so much nicer. Great video.
I wish I could go to home depot and ask them I need a stud pack tile project. And they will have all the stuff you showed ready to pick up. Great job guys
I love the way you teach. You don't assume we have advanced knowledge and all the tools. I also love how you point out your workflow and techniques including what hand you use
i’m jealous of y’alls wonderful dad-son relationship y’all share even at work. Now I need therapy. Haha. You guys are one of my go-to DIY channels. No nonsense but also with some humor, and a lot of love and passion for your trade and skills.
10:11 To avoid voids you should grab some more thinset with the notched edge of the trowel and then trowel the wall. This will create larger thinset lines without any voids, and will provide more coverage. It's also faster than skim coating over voids and troweling over it again.
You guys rock, thank you for putting out quality content. Paul is a badass teacher and Jordan you’re doing great at capturing it all and asking the right questions and putting it all together. You guys are building an encyclopedia of diy help for all of us who aren’t familiar with the tasks, keep crushing!!!
Im in the middle of my first solo tile job. Just an average 3x5 shower with 1x2ft tiles and i've learned so much from this video. Even after working with 2 master craftsman, you dont always get every detail while on the job. Thank you for all the great advice.
These videos are truly instructional. LOTS of information and detail. Having done some tile work (not very well) I have learned much detail on the "proper" way to do things. Keep up the excellent work!
Great DIY tips and tricks and I loved the fact that it's step by step without background music blasting. as we've seen from other home repair workers. Alternatively, I read that "redgard " waterproofing, can be skimmed or painted on, before the adhesive or mortar, as you've seen because all tile work eventually develops cracks behind it that allows water seepage and redgard or any waterproofing membrane prevents or eliminates that nightmare of extra work 5 or ten years in the future. Excellent video and although I've been doing repairs for half of my life, it's always important to see the proper ways and mistakes to avoid time lost, which, as we've all seen, can never be returned.
That was GREAT! I did mine already and I did it 90% like you said, but I didn't know to clean the thin set on the edges before setting, so I had to clean out the squeeze out by hand before grouting. That would have saved me. I have one comment on layout. Use can also use a horizontal accent stripe at about eye level to get rid of slivers at the top.
THanks! Early in my DIY career my cousin ( a tract home framer) taught me about "layout" even on subfloor T&G plywood to minimize cuts and waste AND to have NO slivers (they are ugly and weak)! Best lesson ever! Thanks SP!
Congrats on your DIY career. It appears that Sud Pack has taken at least 1 free Schluter workshop. They mentioned something to this effect in a previous video. If you’re interested then these free workshops are nationwide and I highly recommend them. My experience was awesome and I hope this helps!
I would like to thank you guys for the advice you give. Even though I live in New Zealand and some codes are different the tips are useful. I consider my self to be handy, but not a professional, in most things. I find your channel helps me to try different techniques. You have a talent that not only makes you an income but also saves you a heap on your own projects around your house and property. I also have to mention that guy who controls the video, umm oh yeah Jordan lol, hey buddy great work. Together you make a great team, keep it going, it's an awesome youtube channel. Anyway from a kiwi viewer thank you both for the tips and good luck going forward.
I dig the son father combo, reminds me of me and my son. Small General had the boy working alongside me, he did well. Now works for his buddy and seems to be thriving!
Paul, I have learned so many tips and techniques from you. The thing that is very hard to teach, you do very well, and that is inspiration and work ethic. I don’t see how anyone could watch your channel and not be motivated to improve their work ethic.
You have the best home renovation videos I have ever seen! Super clear video and commentary, tons of tips, perfect pacing, and high quality workmanship that I want to replicate. I even like the background music. :) I'm starting a full bathroom renovation soon, a hired crew will be doing most of the work but I'll be tiling. I have tiling experience but all of the great tips are going to help me be more efficient. I was especially interested in the tips to orient the direction of troweling to create the shortest channels for air to escape and (from another video) using a microfiber towel instead of a sponge to remove grout haze. Congratulations for being only the second content creator I have ever subscribed to.
Beautiful job! I’m not a tiler but have a couple of comments about leveling clips. If you install the wedges pointing toward the already laid tile, it will pull the tiles tight against the clip and the already laid tile. But, if pointing toward the tile being laid, they have a tendency to push the tiles apart and can widen the grout line. Also, when putting the clips in on your last row for the day to come back to the next day, be sure that the wedge is tight against the tile otherwise if there is thinset atop the wedge it won’t pull the tiles even the next day. I insert a small piece of cut-off tile and insert a wedge to hold the cut-off, the tile and the leveling clip in the proper alignmentfor the next morning. It’s a pain to have to cut out the thinset and leveling clip the next day because the clip isn’t up against the tile laid the day before.
Quote: But, if pointing toward the tile being laid, they have a tendency to push the tiles apart and can widen the grout line. That is an issue I have not seen addressed anywhere. I've the wedges put in from tiled previously laid, to the new tile. There has been a time or two when it caused the grout line to open, and I had to fuss with it to make it right. I'll keep your idea in mind. Thanks.
@mic dundee I install the wedges using the pliers tool that is made for installing them and then use a soft white mallet to break the clips and wedges off the next day. My wife discovered the problem with the wedges spreading the grout line. She makes sure the grout lines are all the same width, that the tiles are level in all directions and that there is no lippage. She also takes a bright LED light to painted walls and marks any areas needing touch ups or more of my attention. Teamwork!
Been working Construction most of my life. Currently remodeling my house. My wife is getting anxious to get it finished so she told me to hire someone. I asked, “Who would I hire? I’d pick their work to pieces! I don’t know anyone who would do it and pass my critiquing.” Anyway, I’d hire you all!! (: beautiful work. New favorite channel. Subscribed!!
What a find! So glad I found your channel! Your tips I've learned have worked fanstastic. Thank you for all around being a joy to watch and packing so much into your videos.. The uplifting demeanor you both keep, the editing, shots and staging.. The effort all in all.. It shows and really makes all the difference! Keep up the excellent work guys 💙
I love how you explain, and I love how you compliment/praise (?) who works with you! ♡ Seen several vids from yours, and as far as I can tell you always do it! Must be a great dad or boss. ☆
20:14 I do a diff process once in while when measuring this. I take another tile and come from other side and overlap first tile and make marks…. Just shows more than one way to do things; but, your way means holding 1 tile, and the way I do requires 2 tiles😉 Nice job on set his shower, and aren’t snap cutters just awesome. Imo, they get a bad rap and ppl think need wet saw for cutting tile, b7t even a cheapo $25 snap cutter can do a descent job, if got those skills👍🏻 Cheers✌🏻
Props to Jordan for the camera work (and Paul, you're part was just fine). But I am most impressed with the evolution of Jordan's production skills in assembling the finished video. Great job guys!
@@StudPack The D36000 is the best out there across the board, but the D24000 is awesome also. You guys will love it compared to that Kobalt! Check out contractors direct for best prices out there 👊
Yeah, how to determine the placement of the niche would be very helpful. When I did my shower I placed mine where I felt it was most functional and aesthetic but it caused all sorts of problems when it came to tiling around it. It’s probably the most amateur part of the job I did:(
You have to plan it out before hand. When the old shower is demoed you just determine roughly where the top of you pan tile will be mark a line and figure out the best height for the niche. Doesn’t have to be perfect. You can be off a 1/4 or so and adjust your tile accordingly.
Yeah a little of both. We installed the niche just above our grab bar blocking (as low as we could) then adjusted the tile layout to accommodate the niche. Hope that makes sense 👊
A lot of times we will hold off on installing the kerdi niche until after the walls are up and a good portion of the tile is set. We then cut out for the prefabricated niche, install and water proof. Then we can continue with completing the tile install.
Excellent description and thanks for going to the effort to experiment with different trowel notch sizes. I bought the same levelers to use on my kitchen floor. You showed I better buy the pliers tool. Wish they had those at Home Depot when I did my last tiling in 2020. Ceramic or porcelein tile? On my last home job, I recall I couldn't use my snap-cutter on porcelein so had to wet-saw them. But your snap-cutter is much higher quality. I bought a new diamond blade for my current job.
That last tile on top by the soffit should've been two pieces. As you can tell I'm very anal when laying out tile. I use the same wedges , makes for a perfect surface. Thumbs up !
im so glad you guys just slide the tile trim in. if you ask the guys at HD how to install it they will tell you to screw it in. Its completely unnecessary and makes high spots in your backer. i like these tile clips. for the 1" hole, dont grind. DAP makes tile hole saw. it has a jig and rubber sticker. You just add water and drill away.
Stud pack to the rescue...again. I've been putting off the tiling of my shower because it's kinda intimidating. Not anymore. Your tips and advice are so valuable. Now let's get this shower done.
I have a tradition of watching the home shows on PBS. I've seen around 10 of your videos, but this video proves to me your details are the perfect mix of pace and instruction to have the best outcomes in my project. ps, I'm 1 year now as a handyman professionally in California. Keep them coming, gentlemen. I'll be looking for a way to support your stellar content.
Excellent work as usual The saw holes you can get them easily and inexpensive on Amazon or EBay In fact, I have a set that I bought for $25 ish about 2 years ago and I have probably only used the most common one for the shower head nipple and it still does the job on any hard or soft tile for 2 years now!!!!
Seeing you two work together reminds me of me and my dad back in the day. You all work together so well together. I'm sure they're are days when Jordan is on your nerves about something and the other way around. But I believe those are very few and far in between. Cherish your father Jordan, he's a master at his trade, and leaving a legacy for you. Also thank you for this series, I have never done tile, and will be tackling it this summer in my own house. Thank you for bringing up some memories.
Looks good. I installed 12x24 tile in my shower and it wasn't until I finished that I read on the side of the tile box that you should line up the tile horizontally by removing 30% on each side so that your sides line up better. I don't think that matters in this shower because of the small size but in a bigger sized shower it would. I really enjoy watching you guys make it happen.
THESE VIDEOS ARE TEN TIMES BETTER THAN THIS OLD HOUSE. PASSING ON THE TRADES TO YOUR CHILDREN IS OLD SCHOOL EXCELLENCE. TEACHING THE OLD MAN HOW UA-cam WORKS IS A SYMBIOTIC RELATIONSHIP, KEEP IT UP YOU GUYS. I HAVE WATCHED EVERYONE OF YOUR VIDEOS. ALL THE BIG BOX BUILDING STORES SHOULD BE ADVERTISING ON YOUR VIDEOS. HEY JORDAN YOU NEED TO BE PROMOTING DIRECTLY TO THE BIG BOYS AND MAKE SOME MONEY FOR ALL THE HARD WORK PUTTING THIS STUFF TOGETHER. KEEP IT UP I AM HOOKED !
Good morning, and thanks for another awesome video! I'm not sure if it's been mentioned, but there is a trick when using the leveling spacers. If you forget to put them in at the edge where you finish tiling for today, an easy trick is available. Mr. Sal DiBlasi has it in one of the videos. Use your oscillating tool, I used my grout blade, and grind into the mortar underneath the set tile. You plunge in enough to put the clip into it. Voila! It works great when tying into existing tile as well. I did it when I had to tear out tile in the middle of the field, and replace.
Love all the tips & tricks that you provide WITH an explanation as to why, this is very valuable and helps us remember stuff. Great content, tempo/flow, narration, and camera work! 💯
Something I personally do if I'm cutting out the middle of a tile, I use a cordless grinder (so I don't kill myself) and hold a damp sponge against the side of the blade as I cut. You can squeeze out a little bit of water as you go which helps the cut and keeps the dust down. My blade always chips slightly on the inside of the cut so I just rotate as I'm going keeping the finished edge on the outside of the blade. Done this with porcelain too and it works well for small cuts.
Just found your channel, I am obsessed already, I can clearly see how good you are at what you do and I really appreciate that. I am a little of a perfectionist myself too.
One tip I learned the hard way is make sure there’s no drafts in the room or your Thinset will skin over super quick. There is a HVAC supply vent in the small bathroom I’m working in and I believe the A/C was sucking moisture outta the air and causing it to skin over way too fast resulting in subway tiles that didn’t adhere. Also good idea to soak them if they’re ceramic so they don’t pull moisture out of the top layer of the Thinset too quickly
After watching this awesome video on how to install tile I felt like I could tile the world. Then I started tiling and man it's tough. I managed to complete the shower but it was not that easy as a beginner. Thank you for showing such detail. Next time it should be easier on me.😐
Wow, Paul and Jordan!! Mind blown as I watched and listened to the wealth of information that came from this video!!! It is phenomenal!!! I really kinda feel like you should start another channel on Patreon and make Stud Pack Institute a real thing! You all give so so many tips and techniques to raise a DIY guy’s or homeowner’s game to a professional level. I know I got an old shower stall that’s gonna get a tile upgrade one day and it’s due to you showing me the ropes and giving me the confidence that I can do it right! Major respect and appreciation for all you guys do and how you do it! Jordan you are really blessed to have a Dad you can work with have such a great relationship with at the same time! Love this channel!!! God bless men!
Really enjoy - and learn from - these videos. It's the combination of craftsmanship and ability to communicate that really makes the difference. Thanks, you guys - very much!
There may be a billion videos on tiling, but not many I’d rather watch than STUD PACK! Thanks, guys!
cringe bot comment. the internet is dead
good stuff. Might want to discuss about making sure you always order extra tile. Being 1 or 2 short and then you go to buy another box and it either doesn't exist anymore or the color is slightly different. (plus you always want a few extra to sit in the attic for the next owner to find 30 years later. :-) )
Lol yep
You should always order 10 to 20% extra depending on pattern and layout
I've found those tiles!
It's better to have extra tiles and not need them, then need them and not have them. Lol
I’ve always bought 10% over, for some reason because my brain doesn’t account for areas that give you 2 cuts from 1 tile I always end up with excessive overage
This has been the single most informative and helpful tiling series I have ever watched. I very grateful for all your advice and willingness to instruct.
I can’t tell you how much I love this channel. Paul, you have a real gift for teaching, you’re detailed, clear and concise. Thank you.
Thank you sir 💪🇺🇸🇺🇸🇺🇸
And he has a wonderful personality! 👍
I agree completely and wanted to add that the detail comes through well due to the sincerity of the presentation and passion that Paul brings to it. Well done guys.
Love that you went into detail about the thinset, directional trowel methods and airflow. Lots of channels never teach the why behind the how. Thanks!
As a builder it's refreshing to see other builders take pride in their work and pay attention to detail.
Such an awesome series! As a fellow UA-camr I have just one recommendation - maybe put all of these videos in a playlist so they're easier to find. Took me a bit to sift through and find each new step in the series because of the other vids in between.
I've been a diy, for 40 years, and watching this video I learned something. cool. There was a time, before computers, before cell phones, where people helped each other on their projects, and that was cool, since you could know 90%, if you help knew something too. Since that disappeared, over the years, it's nice to learn something from the videos.
man, this is like getting a master class in stuff like this... thanks guys.
So nice to see the respect you 2 have for each other as father & son while you work together.
Your wife and mom must be so proud.
Super rare
I've been in the trades for over 50 years (Framing, Finish and custom oak stair builder). You guys are really awesome. I love the videos and I love that you are taking the time to teach generations of DIY'ers ...Kudos guys.
I appreciate your mindfulness to keep your videos simple and straight to the point, while avoiding inclusion of irritating music.
Professional tile setter for 20 years. Couple of points.
1. As mentioned by others the top tile on the left wall should be two tiles to match the pattern, although I suspect with your
attention to detail and perfectionism, the next video will be you realizing you oopsied.
2. When doing the layout, if you are using a pure white tile, the thin strip of the tile at the top will disappear visually speaking, when it is grouted with white grout. With a patterned tile perhaps not so much.
That isn't to say you shouldn't have done your layout this way, as it gave you full tiles at the top and bottom of the niche.
The expression I have come up with is that tile setters are trying to create the "veneer of perfection" (all you Frasier fans should take a drink
at this moment!) You can't create perfect but you want the observers eyes to land where you want them to land and not see the fact that
the tiles are not full tile at every wall which would be true perfection. (in 20 years that has only happened once for me). Having full tile at the
top and bottom of the niche draws the eyes. Perfect.
3. When I tile with kerdi, I scratch coat the wall and trowel the notches onto the back of the tile. I find it is less messy. I scratch coat the whole
wall all at once, even if it dries, thin set adheres to itself really well. I trowel the thinset on the back of the tiles out from the center so that the air
still can escape out the grooves. After some practice I can spin up to a 2'x2' tile on my hand (like a pizza) and trowel with the other, or place on
clean water bucket and trowel away.
4. When cutting out the square for the tap hardware, start on the face side. You may need to get a better grinder wheel that cuts cleaner.
I have found some of the best wheels at rental stores. $20 Canadian, can't remember the brand and the name has worn off the wheel.
Tiled 50 bathrooms with 1 grinder wheel and a tile cutter like yours. As well I use a wet diamond pad, about the size of a drywall pad.
Again I think they are in the $20 range. I would go to a tiling supply store if you don't already. They should have them. They
are relatively inexpensive and do the same as your file to smooth the edges, but if you ever get into mitering corners they help a great deal.
As well you can use them to clean cured mud off of your tools to get them back to shiny.
5. Ideally you want the wall tile to land on your sill but with the stone slab that makes the point moot.
6. I have only ever had one hole saw to do the shower head pipe and it is about 1 1/4", Again I don't think too expensive at a tiling supplies store.
7. Keep up the great work. I have learned a lot of fantastic info from you about other aspects of construction. Your skills are what got me
to start watching your channel, your humility keeps me watching!
Feel free to pick my brain if you want on tiling questions
Super appreciate that 👊👍. I noticed the top tile when we did the outtro 😡. Last tile…. Not thinking it through…. Working till 7pm… all the excuses right 👊👍
@@StudPack That's why I always...ALWAYS stop at 6:59 ;)
I wouldn't call the 5 inch cut at the top a thin strip
@@markme4 I think he was referring to the thin sliver at the top they would have had if they hadn't split the top and bottom tiles.
@@isaacholzwarth Yea you're probably right but that looks like it would have been 4 to 5 inches as well
I like that you show the tips and tricks for people who have never done this before at all. Too many youtube videos assume a much greater level of experience in construction than a lot of us actually have...
Wow. I've watched a number of very good videos on tiling, but you are so thorough, showing, discussing and explaining every aspect of the job, I feel like I'm there with you learning as you do it. Combine that with your knowledge, expert technique and attention to details to all aspect of the work/job is incredible. Very glad I discovered your channel.
Had to pause the video and write this comment. Of course I’m going to learn something on this video. You’re one of the only ones on here that really explains technique the why’s of everything you do. You make it easy to follow and entertaining as well.
If there are any DIYers out there who skipped to this video, without watching the others, you will miss the most important aspect of tiling, and that is prep. Paul’s tile goes on so nicely because he spent so long making sure he had a flat square and plumb surface to attach it to.
In my early years I learned this the hard way. Rushed the set up because I thought I was good enough to fix/hide/cheat any problems I would run into. One client, one shower changed that way of thinking. I'll never forget it. That day I learned a lesson and went from pro to expert at that moment when I knew i'd always spend more time prepping than laying from that job on.
@@ProToolsApproved Yep. Tile stobbornly refuses to bend! Great that you got the lesson, though. As I’ve gotten older, and I am almost 56 now, I have come to regard these as “kick in the ass” moments, which I recognize faster, learn the lesson, and welcome the next one.
Well you can prep all you want like my husband did and then when the tiler's came in they made a worse mess than what he'd already tore out. There was no waterproofing before and they still didn't waterproof it in the new installation.
There is no grout in the walls they used clear silicone with white porcelain...? I have two standing 1/8 inch deep puddles 4 inches away from the drain hole..?? The uprights for the shower slider doors half on porcelain half on plasterboard. The tiles on the wall one foot by 2 ft some hang an eighth of an inch out over the tile below and others are the opposite. And up to half inch gap in bottom corner tile just filled in with silicone. The list goes on.
Now my husband's a disabled veteran that's why it took him so long to tear a small 6x9 bathroom apart, and it was supposed to be a present for him. Bottom line is... it must be all tour back out and redone floor to ceiling. The help he got was from family who has been building homes for three generations. So much for family and all that love. You should see the let down in his eyes,.. it's heartbreaking.
Every video is from this start forward. Prep is hardest, most important, and most of the work
Sooooo True
Your the first tile person that I see using straight collapsing channels of thinset. Almost never see anyone doing tile the right way. When I tell people about trapped air I usually show them by dropping a coin on their tile floor using the hollow sound to show voids. Really appreciate the professionalism.
I love your videos. I'm learning as fast as I can, tiling a master bath walk-in shower with 12 x 24 tiles, and pebble floor, now. One thing that I learned that you don't have in there is to put the leveling system Ts behind the ledger strips so that the bottom tiles can be leveled when they are installed. Don't forget to lower your ledger strips the appropriate amount to make up for the additional height that the Ts add to the ledger. Also, be sure that you put the Ts in all of the correct places for the tiles to be installed above and below.
The most impressive skill I've seen you perform is to do such a good job without metric measurements. That's probably the most impressive thing about America in general. Well done. Keep it coming.
I personally get a little laugh because when I was a contractor, especially with tile, I never got to go home as clean as you guys lol. Great work and very informative video. Thanks for sharing the art and precision that goes into these jobs
Your a great instructor, as far as cutting the holes for the fixtures, I used 15.00 bit, what it was was a Dremel tile bit with a rotozip tool. I cut 5 holes and it's pretty much done for. But for the price I can't complain. It was worth it's weight in gold..
I don't think I'll ever try this stuff, myself, but I love seeing your work, your method for teaching, and your explanation of the full process PRIOR to starting it. I think a lot of DIY channels could learn a thing or two from your presentation!
My last house flip was 16 years ago. Your video is a nice refresher to get my brain into shape before I tackle a bathroom demo and rebuild. So many original crimes by the builder! I like your "Story Pole" 2x4.
I'll look for your other videos.
Number one tip I've got from this series is cleaning the edges with a margin trowel before installing each tile. Seems obvious now, but it never occurred to me when I did my shower. Spent a *lot* of time cleaning out the joints before grouting. 😞
Great content as always, gents. Keep up the good work!
You don't need a margin trowel, just use the corner of your half inch trowel. One less tool to keep in the tight space.
Just clean the joints with a pick or pencil as you go.
It's always the little things that make or break the project, Paul covers them all.
Using a thinset (available in white) and grout of the same color saves a lot of work there....
I actually use one of the wedges for the leveling system to clean it off.
Set tile with my dad back in the late 70's and mid 80's. Thought I knew a few things but you took it to another level!! Thank you for the insight and tips! Outstanding!
You can also add an accent band or stripe (pencil tile) to make the layout work .both of those holes look great from my house 😁
Great way to avoid slivers
Good idea.
Personally I always assumed the reason tile companies sell tiles with dimensions slightly less than 1 or 2 foot is to compel us to buy accent strips. ;)
I would probably just open the grout lines like 1/16? to keep a full tile at the bottom and eliminate the sliver. Or possible try to factor that in when determining the slope of the pan. There’s so much to think about and everyone has different taste. That’s what I love about tiling.
Another option which I like is to have a horizontal strip mid wall of a contrasting title that's 3,4,6". That allows me to always have a full tile at the bottom and cut a little off the tile at the ceiling. Plus the contrasting strip is always going to be seen as a more custom job, higher value.
I like that that doesn't leave a cut tile at the bottom that's difficult to silicone.
S.P., I love how y'all are really zero'ing in on anticipating questions. Example, the leger, exactly when I was thinking about the screws holing the ledger board, y'all said you'll patch them with a little curdy as you do the bottom course. Very cool!
Got to add, once of the best shower tiling videos I've seen. One of your best as well, IMSHO. Very inspiring, considering I've got a master suite I really need to get to. Thank you again.
Hire the Stud Pack!
@@moneyfornothing3264 Distance and Money.
I live in N. Texas, and budget constraints push to DIY. FWIW, I'be already built furniture, cabinets, electrical, some plumbing, and have done siding on the house.
Tiling and some of the finer finishing things are left to be personally explored. But I will get there. SP has really helped.
I’ve owned rental’s for over 30 years and mostly did my own work. I had to learn how to do everything myself, because I would pay someone to do it and then have to redo it. I’m retired now and I don’t have anymore rentals so I don’t have to learn this stuff anymore but I find myself addicted to your videos. I love all of your tips and tricks. I especially love your tip for hanging drywall on the ceiling. I highly recommend anyone that hasn’t seen it to go back and watch it.
You could use painters tape to lay out the lines with the speed square on the front side of the tile. Then cut with the grinder from the front side and inside the tape line. The tape won't mark the tile and it helps prevent too many chips.
Thank you so much. Had no idea I could get metal edging trim, last time I did this job 20 years ago I just used plastic cove trim. The metal looks so much nicer. Great video.
I wish I could go to home depot and ask them I need a stud pack tile project. And they will have all the stuff you showed ready to pick up. Great job guys
I love the way you teach. You don't assume we have advanced knowledge and all the tools.
I also love how you point out your workflow and techniques including what hand you use
Nice job Paul, you’re a natural in front of the camera and it’s really great to see a perfectionist doing this type of work. Well done!
i’m jealous of y’alls wonderful dad-son relationship y’all share even at work. Now I need therapy. Haha.
You guys are one of my go-to DIY channels. No nonsense but also with some humor, and a lot of love and passion for your trade and skills.
10:11
To avoid voids you should grab some more thinset with the notched edge of the trowel and then trowel the wall. This will create larger thinset lines without any voids, and will provide more coverage. It's also faster than skim coating over voids and troweling over it again.
All this man years of experience, shared to the world for free. Thank you 🙏🏽
You guys rock, thank you for putting out quality content. Paul is a badass teacher and Jordan you’re doing great at capturing it all and asking the right questions and putting it all together. You guys are building an encyclopedia of diy help for all of us who aren’t familiar with the tasks, keep crushing!!!
Great team and brilliant work.
Im in the middle of my first solo tile job. Just an average 3x5 shower with 1x2ft tiles and i've learned so much from this video. Even after working with 2 master craftsman, you dont always get every detail while on the job. Thank you for all the great advice.
These videos are truly instructional. LOTS of information and detail. Having done some tile work (not very well) I have learned much detail on the "proper" way to do things. Keep up the excellent work!
Great DIY tips and tricks and I loved the fact that it's step by step without background music blasting. as we've seen from other home repair workers.
Alternatively, I read that "redgard " waterproofing, can be skimmed or painted on, before the adhesive or mortar, as you've seen because all tile work eventually develops cracks behind it that allows water seepage and redgard or any waterproofing membrane prevents or eliminates that nightmare of extra work 5 or ten years in the future. Excellent video and although I've been doing repairs for half of my life, it's always important to see the proper ways and mistakes to avoid time lost, which, as we've all seen, can never be returned.
That was GREAT! I did mine already and I did it 90% like you said, but I didn't know to clean the thin set on the edges before setting, so I had to clean out the squeeze out by hand before grouting. That would have saved me. I have one comment on layout. Use can also use a horizontal accent stripe at about eye level to get rid of slivers at the top.
I’ve found that a popsicle stick is great for cleaning the thin set from between the tiled when the thin set is fresh…A DYI FYI
THanks! Early in my DIY career my cousin ( a tract home framer) taught me about "layout" even on subfloor T&G plywood to minimize cuts and waste AND to have NO slivers (they are ugly and weak)! Best lesson ever! Thanks SP!
Congrats on your DIY career. It appears that Sud Pack has taken at least 1 free Schluter workshop. They mentioned something to this effect in a previous video. If you’re interested then these free workshops are nationwide and I highly recommend them. My experience was awesome and I hope this helps!
I would like to thank you guys for the advice you give. Even though I live in New Zealand and some codes are different the tips are useful. I consider my self to be handy, but not a professional, in most things. I find your channel helps me to try different techniques.
You have a talent that not only makes you an income but also saves you a heap on your own projects around your house and property. I also have to mention that guy who controls the video, umm oh yeah Jordan lol, hey buddy great work. Together you make a great team, keep it going, it's an awesome youtube channel.
Anyway from a kiwi viewer thank you both for the tips and good luck going forward.
This is literally the best Tile tutorial video I’ve seen. Hoping to tackle a tile project soon now.
I like your idea of laying the tile out on the floor is sure simplify’s the process. Great video as usual!!!
I dig the son father combo, reminds me of me and my son. Small General had the boy working alongside me, he did well. Now works for his buddy and seems to be thriving!
DIY-ing my own tile shower tomorrow and I can’t thank you enough for all this great information! THANK YOU STUD PACK! 🙏🏻🙏🏻
You're welcome Ryan! Thx for the support and best of luck with your project 👍
Paul, I have learned so many tips and techniques from you. The thing that is very hard to teach, you do very well, and that is inspiration and work ethic. I don’t see how anyone could watch your channel and not be motivated to improve their work ethic.
9:20 I think that you do a really good job of explaining the process in a way that I intuitively connect to. Good Job!
You have the best home renovation videos I have ever seen! Super clear video and commentary, tons of tips, perfect pacing, and high quality workmanship that I want to replicate. I even like the background music. :) I'm starting a full bathroom renovation soon, a hired crew will be doing most of the work but I'll be tiling. I have tiling experience but all of the great tips are going to help me be more efficient. I was especially interested in the tips to orient the direction of troweling to create the shortest channels for air to escape and (from another video) using a microfiber towel instead of a sponge to remove grout haze. Congratulations for being only the second content creator I have ever subscribed to.
Fantastic stuff. Getting ready to tile a kitchen wall, floor, and two bathrooms. Should be fun times! Thanks for all you two do.
I've watched a lot of online tiling videos, and this is one of the best tutorials, setting me up well for my first tiling job!
Beautiful job! I’m not a tiler but have a couple of comments about leveling clips. If you install the wedges pointing toward the already laid tile, it will pull the tiles tight against the clip and the already laid tile. But, if pointing toward the tile being laid, they have a tendency to push the tiles apart and can widen the grout line. Also, when putting the clips in on your last row for the day to come back to the next day, be sure that the wedge is tight against the tile otherwise if there is thinset atop the wedge it won’t pull the tiles even the next day. I insert a small piece of cut-off tile and insert a wedge to hold the cut-off, the tile and the leveling clip in the proper alignmentfor the next morning. It’s a pain to have to cut out the thinset and leveling clip the next day because the clip isn’t up against the tile laid the day before.
Quote: But, if pointing toward the tile being laid, they have a tendency to push the tiles apart and can widen the grout line. That is an issue I have not seen addressed anywhere. I've the wedges put in from tiled previously laid, to the new tile. There has been a time or two when it caused the grout line to open, and I had to fuss with it to make it right. I'll keep your idea in mind. Thanks.
@mic dundee I install the wedges using the pliers tool that is made for installing them and then use a soft white mallet to break the clips and wedges off the next day.
My wife discovered the problem with the wedges spreading the grout line. She makes sure the grout lines are all the same width, that the tiles are level in all directions and that there is no lippage. She also takes a bright LED light to painted walls and marks any areas needing touch ups or more of my attention. Teamwork!
Been working Construction most of my life. Currently remodeling my house. My wife is getting anxious to get it finished so she told me to hire someone. I asked, “Who would I hire? I’d pick their work to pieces! I don’t know anyone who would do it and pass my critiquing.”
Anyway, I’d hire you all!! (: beautiful work. New favorite channel. Subscribed!!
What a find! So glad I found your channel! Your tips I've learned have worked fanstastic. Thank you for all around being a joy to watch and packing so much into your videos.. The uplifting demeanor you both keep, the editing, shots and staging.. The effort all in all.. It shows and really makes all the difference! Keep up the excellent work guys 💙
I love how you explain,
and I love how you compliment/praise (?) who works with you! ♡
Seen several vids from yours, and as far as I can tell you always do it! Must be a great dad or boss. ☆
20:14 I do a diff process once in while when measuring this. I take another tile and come from other side and overlap first tile and make marks…. Just shows more than one way to do things; but, your way means holding 1 tile, and the way I do requires 2 tiles😉
Nice job on set his shower, and aren’t snap cutters just awesome. Imo, they get a bad rap and ppl think need wet saw for cutting tile, b7t even a cheapo $25 snap cutter can do a descent job, if got those skills👍🏻
Cheers✌🏻
Props to Jordan for the camera work (and Paul, you're part was just fine). But I am most impressed with the evolution of Jordan's production skills in assembling the finished video. Great job guys!
Slivers are our enemy! Great video guys.
We beat the slivers, but fought the tile saw 😭are you still rocking the D36000? appreciate the support man 👊
@@StudPack The D36000 is the best out there across the board, but the D24000 is awesome also. You guys will love it compared to that Kobalt! Check out contractors direct for best prices out there 👊
I find it very satisfying to watch the transformation step by step. I’m such a nerd.
QUESTION....Was the neich's location planned according to the size of your tile? or did you just get lucky that it lined up perfect?
Yeah, how to determine the placement of the niche would be very helpful. When I did my shower I placed mine where I felt it was most functional and aesthetic but it caused all sorts of problems when it came to tiling around it. It’s probably the most amateur part of the job I did:(
You have to plan it out before hand. When the old shower is demoed you just determine roughly where the top of you pan tile will be mark a line and figure out the best height for the niche. Doesn’t have to be perfect. You can be off a 1/4 or so and adjust your tile accordingly.
Yeah a little of both. We installed the niche just above our grab bar blocking (as low as we could) then adjusted the tile layout to accommodate the niche. Hope that makes sense 👊
@@StudPack Thank you.
A lot of times we will hold off on installing the kerdi niche until after the walls are up and a good portion of the tile is set. We then cut out for the prefabricated niche, install and water proof. Then we can continue with completing the tile install.
Excellent description and thanks for going to the effort to experiment with different trowel notch sizes. I bought the same levelers to use on my kitchen floor. You showed I better buy the pliers tool. Wish they had those at Home Depot when I did my last tiling in 2020. Ceramic or porcelein tile? On my last home job, I recall I couldn't use my snap-cutter on porcelein so had to wet-saw them. But your snap-cutter is much higher quality. I bought a new diamond blade for my current job.
That last tile on top by the soffit should've been two pieces. As you can tell I'm very anal when laying out tile. I use the same wedges , makes for a perfect surface. Thumbs up !
I didn't even notice until I read your comment. Good call. One of those things that would drive me nuts later every time I saw it.
Nice catch
I saw that when filming the outtro and my heart sank 😡😡😡. That’s what I get for working till 7pm 😣
Your communication skills and your efficiency with your words are amazing….Thanks for the knowledge……
Watching and listening to you guys almost convinces me that I could do tile work. Thanks for sharing your knowledge.
Best tips and best explanations I've seen in one video. Awesome job-I'm finishing a basement and about to do a very similar shower tile job. Thanks!
This is a great video. I was notching my tiles along with the wall & only using the screw levelers at the seams. Thanks for the directions!
im so glad you guys just slide the tile trim in. if you ask the guys at HD how to install it they will tell you to screw it in. Its completely unnecessary and makes high spots in your backer. i like these tile clips. for the 1" hole, dont grind. DAP makes tile hole saw. it has a jig and rubber sticker. You just add water and drill away.
Always love to watch a good tiler work. You explain everything well and speaking with a clear voice.
Stud pack to the rescue...again. I've been putting off the tiling of my shower because it's kinda intimidating. Not anymore. Your tips and advice are so valuable. Now let's get this shower done.
The tile leveling system is a game changer. The last three showers I've tiled have turned out great, no lippage. Great video!
I have a tradition of watching the home shows on PBS. I've seen around 10 of your videos, but this video proves to me your details are the perfect mix of pace and instruction to have the best outcomes in my project. ps, I'm 1 year now as a handyman professionally in California. Keep them coming, gentlemen. I'll be looking for a way to support your stellar content.
Excellent work as usual
The saw holes you can get them easily and inexpensive on Amazon or EBay
In fact, I have a set that I bought for $25 ish about 2 years ago and I have probably only used the most common one for the shower head nipple and it still does the job on any hard or soft tile for 2 years now!!!!
You are very good at teaching! Easy to understand, logical progression, even explaining the reasonings, using a minimal amount of words! Great job!!!
Seeing you two work together reminds me of me and my dad back in the day. You all work together so well together. I'm sure they're are days when Jordan is on your nerves about something and the other way around. But I believe those are very few and far in between. Cherish your father Jordan, he's a master at his trade, and leaving a legacy for you. Also thank you for this series, I have never done tile, and will be tackling it this summer in my own house. Thank you for bringing up some memories.
Looks good. I installed 12x24 tile in my shower and it wasn't until I finished that I read on the side of the tile box that you should line up the tile horizontally by removing 30% on each side so that your sides line up better. I don't think that matters in this shower because of the small size but in a bigger sized shower it would. I really enjoy watching you guys make it happen.
Always amazed me how tile guys get it done. You got a great son and you guys make up a great team. Keep up the good work
THESE VIDEOS ARE TEN TIMES BETTER THAN THIS OLD HOUSE. PASSING ON THE TRADES TO YOUR CHILDREN IS OLD SCHOOL EXCELLENCE. TEACHING THE OLD MAN HOW UA-cam WORKS IS A SYMBIOTIC RELATIONSHIP, KEEP IT UP YOU GUYS. I HAVE WATCHED EVERYONE OF YOUR VIDEOS. ALL THE BIG BOX BUILDING STORES SHOULD BE ADVERTISING ON YOUR VIDEOS. HEY JORDAN YOU NEED TO BE PROMOTING DIRECTLY TO THE BIG BOYS AND MAKE SOME MONEY FOR ALL THE HARD WORK PUTTING THIS STUFF TOGETHER. KEEP IT UP I AM HOOKED !
Much appreciated Chuck 👊👍
Love your comment… but with all the ALL CAPS then it feels like I’m being yelled at. 😏😁😙👍
@@insecureinvestorchallenge7366 These guys deserve a shout out!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
@@chuckerickson6721 😆😄💯👍
Thanks
Good morning, and thanks for another awesome video! I'm not sure if it's been mentioned, but there is a trick when using the leveling spacers. If you forget to put them in at the edge where you finish tiling for today, an easy trick is available. Mr. Sal DiBlasi has it in one of the videos. Use your oscillating tool, I used my grout blade, and grind into the mortar underneath the set tile. You plunge in enough to put the clip into it. Voila! It works great when tying into existing tile as well. I did it when I had to tear out tile in the middle of the field, and replace.
Love all the tips & tricks that you provide WITH an explanation as to why, this is very valuable and helps us remember stuff. Great content, tempo/flow, narration, and camera work! 💯
I rarely comment on videos. This dude does such a fantastic job of teaching that I feel compelled to drop a "thank you".
I appreciate that!
Something I personally do if I'm cutting out the middle of a tile, I use a cordless grinder (so I don't kill myself) and hold a damp sponge against the side of the blade as I cut. You can squeeze out a little bit of water as you go which helps the cut and keeps the dust down. My blade always chips slightly on the inside of the cut so I just rotate as I'm going keeping the finished edge on the outside of the blade. Done this with porcelain too and it works well for small cuts.
Just found your channel, I am obsessed already, I can clearly see how good you are at what you do and I really appreciate that. I am a little of a perfectionist myself too.
This is some of the best tiling content on UA-cam. Thanks!
Great job man. Been doing this 20 yrs. Yur one of the best.(details) . You knowledge and your ability to see the next step is amazing.
You are making it easy for a visual person like me to build confidence in doing tile. New tools, products and concepts. Thanks
Great respect for this profesional man and great to see someone installing those metal trims the right way .!!
Thanks!
One tip I learned the hard way is make sure there’s no drafts in the room or your Thinset will skin over super quick. There is a HVAC supply vent in the small bathroom I’m working in and I believe the A/C was sucking moisture outta the air and causing it to skin over way too fast resulting in subway tiles that didn’t adhere. Also good idea to soak them if they’re ceramic so they don’t pull moisture out of the top layer of the Thinset too quickly
Would love to see you guys do a video about how you organize and store all the tools you use for all the different trades you cover.
Thanks for sharing your craft and positive spirit.
Much gratitude .
By far my favorite team !
After watching this awesome video on how to install tile I felt like I could tile the world. Then I started tiling and man it's tough. I managed to complete the shower but it was not that easy as a beginner. Thank you for showing such detail. Next time it should be easier on me.😐
Wow, Paul and Jordan!! Mind blown as I watched and listened to the wealth of information that came from this video!!! It is phenomenal!!! I really kinda feel like you should start another channel on Patreon and make Stud Pack Institute a real thing! You all give so so many tips and techniques to raise a DIY guy’s or homeowner’s game to a professional level. I know I got an old shower stall that’s gonna get a tile upgrade one day and it’s due to you showing me the ropes and giving me the confidence that I can do it right! Major respect and appreciation for all you guys do and how you do it! Jordan you are really blessed to have a Dad you can work with have such a great relationship with at the same time! Love this channel!!! God bless men!
wish i had watched this before I did my bathroom - had no idea you could get anything but the small + spacers - brill video
Really enjoy - and learn from - these videos.
It's the combination of craftsmanship and ability to communicate that really makes the difference.
Thanks, you guys - very much!
Nice video. A couple of genuine guys doing a genuine days work. Lovely job
I really enjoy watching your videos. They are very informative and you are a natural teacher.