Thanks for the call out to locktight #3 at 9:00 in, never heard of the stuff before, and "aviation sealant" brought up too many responses to narrow it down. look forward to learning more about what all this can do.
I like how much fun you guys have while you are solving one problem after the other. Thanks for showing us what it's like to have confidence and competence. One isn't much good without the other. Goodonya!
Another awesome episode guys. So cool to see my name at the end along with the other Patreon supporters. Stoked to be able support you guys and to vote with my wallet on what I think is great content
I used to make steel braided lines in a specialty shop, if you put some tape around the line before you cut it it controls most of the outer steel part and makes pushing on fittings easier. Just makes life a little easier
Many years ago, 2004 I think it was, I replaced the lifters in my VLt in my tiny garage as they were noisy. Watching Al do it brought back a whole lot of memories. I lubricated the hell out of everything as I put it back together, but didn't have a torque wrench, so just did everything up 'tight'. Thinking back, I'm damn lucky nothing went bang, because I gave that car a belting.
Always bummed when these episodes finish ! Great work guys , brings back many early 90's memories for me as I built a ripper BT1 over many years and I had sooo much fun in that thing ! Wish I could do it again now with all the advanced goodies to choose from ! The old girl was just shy of 550HP back then , the mind boggles at what could be achieved these days and how much better it would be !!
This is awesome, love the new series, love the no-nonsense tech info. Since I am in the states its super cool to learn the history as most if not all of the stuff we've never even heard of before.
Awesome video guys. I've been watching you since the first 1. This is one of the best Australian channels and you should have way more subs and views. I used to own a VL so now you know I'm from OZ, SA in fact.. Keep the videos and your great knowledge coming. I've rebuilt many engines but your insight, knowledge, experience and the way you explain everything is just great. Cant wait to see how the turbo VL performs
One alternative to using two nuts to drive the studs in, is to use a long nut with a pin driven on the end. It bottoms out, you drive the stud in, remove the pin (sloppy fit's ok) and you can then remove the nut. Old racer trick (apparently).
![THE SKID FACTORY - RB30E+T Holden VL Commodore [EP7]](http://i.ytimg.com/vi/0LAnw21VnAg/mqdefault.jpg)
![THE SKID FACTORY - RB30E+T Holden VL Commodore [EP7]](/img/tr.png)
![THE SKID FACTORY - RB30E+T Holden VL Commodore [EP10]](/img/n.gif)
25 minutes!?! This has to be good 👌
and they still went by way too fast
@@MariusAraujo WAYYYYY too fast!
Turbo Yoda is a gentleman. I doubt he would ever put it in dry. That Woody on the other hand... ;P
Homoerotic car humor. Original ;-P
@@numinous4789 Hey it can be either! 😂
For sure. Def spits on it first.
If I were a human female, I'd definitely want to give birth to Al's love child.
@@ArKritz84
If you're not human, how are you typing this tweet?
You know you are going to have a good day when the Skid factory releases another video!
This guy
When are you due to be released from prison ?
@@sheelindecor7593 wat
@@sheelindecor7593 what?
3:20 ...... brother loves an Amen!! Nice chopping there Moog
The skid factory is one of the best programs on tv or the internet
12:22 Truer words have never been spoken than "every valve cover should be wrinkle red."
Unless the valve cover goes on a real engine, in which case it would be Ford Blue.
@@scottthompson292 why would you paint the top of a trash can blue?
Recovering from surgery in hospital. the skid factory release a video. God sent! You made my day keep up the good work!
That rocker assembly design is so nice.
Appreciate that you showed the making of the oil line/s for the turbo. Something that is simple but often not shown.
the Cummins badge a clue to next diesel build??
Cummins Patrol because the Nissan diesel wasn't cutting it! :P
@Nick Galm Have you watched the diesel Patrol vids?
@Nick Galm diesel swap into a Nissan Patrol, not an engine build though.
@@justinrobertson5493 Most oil burners dont need internal spannering, Just a clean up and bolt on.
Cummins Patrol confirmed
I wish I lived in Australia. Damn you guys have a massive car culture. Respect from South Africa
A minute and a half ad.... longest I’ve ever watched on UA-cam, worth it for Skid Factory!
Listening to alan is a tonic makes me interested in continuing to learn more than i do
great work men🍋🍋🍋
All those yt subscriptions, all those vid's... Skid Factory is always the first! 💕💕👌
bwahahaha. I was wondering how many times you had to do that take with the bin.
Came here to ask that also! LOL!
As good as Al is I knew it had to take more than 1 try lol.
Thanks for adding reference information for line sizes and hose type. Really helps for future DIY projects.
Thanks for the call out to locktight #3 at 9:00 in, never heard of the stuff before, and "aviation sealant" brought up too many responses to narrow it down. look forward to learning more about what all this can do.
Such a treat after a big day at the orifice, tunes are great too....thanks fellas
Awesome to hear that tune/track again from few episodes back at 3:13! I would instantly buy it if they released it as a track!
Great watching a show by professionals that know their craft.
I like how much fun you guys have while you are solving one problem after the other. Thanks for showing us what it's like to have confidence and competence. One isn't much good without the other. Goodonya!
Another awesome episode guys. So cool to see my name at the end along with the other Patreon supporters. Stoked to be able support you guys and to vote with my wallet on what I think is great content
heroes.
Haha Al at 2:50, i was in glasses denial for years, until my arms weren't long enough to bloody focus. Love the channel guys.
I used to make steel braided lines in a specialty shop, if you put some tape around the line before you cut it it controls most of the outer steel part and makes pushing on fittings easier.
Just makes life a little easier
Many years ago, 2004 I think it was, I replaced the lifters in my VLt in my tiny garage as they were noisy. Watching Al do it brought back a whole lot of memories. I lubricated the hell out of everything as I put it back together, but didn't have a torque wrench, so just did everything up 'tight'. Thinking back, I'm damn lucky nothing went bang, because I gave that car a belting.
spot on! nice one for another video and one of proper length! i can't get enough of full length vids vs tabbing up short ones in a row!
Credit to your production quality and editing.. a lot of work and great shots... really great to watch well-done guys
Always bummed when these episodes finish ! Great work guys , brings back many early 90's memories for me as I built a ripper BT1 over many years and I had sooo much fun in that thing ! Wish I could do it again now with all the advanced goodies to choose from ! The old girl was just shy of 550HP back then , the mind boggles at what could be achieved these days and how much better it would be !!
Can't wait to see the valve cover internal camera footage of the first start.
That turbo looks staunch on that motor!! Very nice.
yes, i'm sure it's very loyal, being from a ford and all...
This is awesome, love the new series, love the no-nonsense tech info. Since I am in the states its super cool to learn the history as most if not all of the stuff we've never even heard of before.
Wrinkle red is a deff must !!!
I like the picture of Kramer in the background
That RB30E+T at the end waiting to go in, looks sick! Good work boys!
Get these legends to 100,000.
School is important and all, but when an episode of THE SKID FACTORY is released, assignments have to wait 😂
Y’all make my day🙌
So stoked to see all the patreon love. I love the tunes you guys use. It makes me want to get in the shed and spin spanners on my 80s junk subaru B-)
Yay! New music from Moog! Diggin' it! And of course I always love my Skid Factory. You guys inspire me!
Hey Woody quick neat trick get a big ass clear tub you can use it to cover your work in between coats.
Moog, release the skid Factory music!!!!!! All of it! I like the back ground music of this episode!!!!
Al holds that cam card like he's reading a fortune cookie message
Thankyou Al, for the use of my favourite word "Dunger". Deadset pair of Legends.
My new favorite car build UA-cam channel! Keep up the awesome work.
Everything about this episode made me smile!
Committed to that 5:50 ad for you boys. Always worth the wait. Cheers
now that is a proper length episode.
Great song when you guys were putting in the cam! Always enjoy your videos!!
Love the "vee log piss take" Much air snorted out of my nose. Best car channel guys keep it up!
Dont eva change you two bounce off each other its such a crack up
It would be awesome to see a daily vid. Thumbs up lads
I want that damn air chuck with the incorporated blower nozzle. have looked everywhere without luck!!!
Great video guys, I learn something every time I watch a Skid Factory video.
Thanks guys 👌🏻
Kills me waiting for these videos to come out. Love it boys
Damn. One hell of a good cliff hanger. Cant wait to see it in the car.
Another great episode guys 👍
Very creative shots!
Well done outtakes
That patreon list! 👌🏼 great work fellow viewers
Great series guys, loving this build
Epic job there lads.... outtakes at the end were lol... massive air high 5 to u both
"Don't put it in dry" That's all around good advice for any situation.
Engine’s looking sweet guys! Love that Patreon roll at the end.👍🏼🤘🏼😎
how could 4 people dislike this even when it hasnt been out long enough to watch it in full!
liked before i even watched!
James Whelan clearly people who’ve been chopped by VL turbos before 😂
Not fair, I have too much work to do and another Skid Factory video drops!
I even let the ads play through for these guys, quality content 😎
Good stuff as usual guys.
Keep up the great work Yoda and Woody!
Choo Choo!!!! Movin' toward completion!!! Thanks for a the vid!!!
Fit and see. Hopefully everything works out. 😉👍👍
AN fittings sound like the performance stickers they add hp
It annoys me the people can unlike these videos if they dislike it they shouldn’t be watching it keep up the grate videos 👌
Could watch this guy work on an RB all day long
Woody, buy some scotch brite pads. Watching you use a sanding block on that valve cover is painful. You'll thank me later
wabamad I know right?!!
thats a mean looking straight 6, the wrinkle red for sure is the icing on the cake
I did wonder how many takes launching it into the bin.
Loving the new channel (well stand alone) stuff dudes. Keep it coming strong.
best series on youtube well done boys
Hahaa! I thought that right shoulder throw couldn't have been the first take. Good episode boys.
Semen injectors had me in fits !
You guys are the best!
Loving this channel. Loving the videos. Keep it up Yoda and Rodriguez.
Awesome video guys. I've been watching you since the first 1. This is one of the best Australian channels and you should have way more subs and views. I used to own a VL so now you know I'm from OZ, SA in fact.. Keep the videos and your great knowledge coming. I've rebuilt many engines but your insight, knowledge, experience and the way you explain everything is just great. Cant wait to see how the turbo VL performs
A 24 minute video that's pretty nice
really loving this vl commodore rebuild guys - only critique would be that it would be awesome to know how you lined up the cam and crank :)
With the timing marks.
This channel brings me such joy when a notification bell rings for a new vid! Cheer
Nice long episode; cheers guys!
great job guys
Slowly but surely towards the 100k subscribers
One alternative to using two nuts to drive the studs in, is to use a long nut with a pin driven on the end. It bottoms out, you drive the stud in, remove the pin (sloppy fit's ok) and you can then remove the nut. Old racer trick (apparently).
yeah, but you need a long nut for that. it's more likely you would have two nuts of the correct size to hand.
Over the shoulder round file shot is a thing of legends. Be gone.
Keep up the good work on the imitation pigeon machine!
I'm learnding - thanks guys :)
Great beat @3:13!
Another really detailed episode, awesome work! Did wonder if the bin chuck was one take or not 😂
I can’t go to sleep knowing there is a Skid Factory video waiting for me.
Skid Factory? yes, please
Great channel. Very entertaining and lots of interesting shenanigans haha
That looks so sick aye great job. 👍🤙 cant wait for first start.
Hey thats some good tunes mate
Great content boys keep it up