Hello sir. Made my own battery pack same as your presentation. Charged it perfectly for the first time then used it til it becam low battery. But upon charging, it wont charge. Whats the possible reason? I followed the same diagram as yours. Thanks
Check the battery voltage. If output voltage is less then 8.4v then might one cell damage. Then you need the removing all connection and check the 3 cell separately. Which battery cell voltage less than 2.4v you need to replace this battery another good one.. thank you
सर इस १२ वॉल्ट की बॅटरी को चार्ज करने के लिये bms को १२ वॉल्ट के लिये खेत का स्प्रे पंप का चार्जर १२वॉल्ट ८amp इस्तेमाल करे या मोटर सायकल की बॅटरी का चार्जर १२ वॉल्ट ४amp वाला इस्तेमाल करे?
@@kennmossman8701 BMS is designed to cut off the charging voltage when the battery is full. This is an essential safety feature to prevent overcharging, which can damage the battery, create safety hazards, and reduce the battery's lifespan. The BMS monitors the voltage of the battery cells during charging, and when it detects that the cells have reached their maximum safe voltage level, it will disconnect the charging source to stop the charging process. BOKACHODA
@@cubityt where do you get this - try reading technical articles show just one BMS datasheet that supports your claims - speficially that -any bms will recognize all cells are fully charged -the bms will turn off power from the charger I will not wait because you wont find any.,
Bms is a battery management system. without bms for example: when charging some cell are over voltage and some cell not fully changed. when discharging then some cell are fully discharged and other cell are not fully discharged.
@@cubityt brother🙏with DMM measured voltages on BMS, 3S, 20A module as 3.83v, 7.3V, 11.36v, by placing DMM black probe at Ov. But the o/p is 7.7V only. I am using 6 batteries total, 2in parallel each(for high current), with 3 pairs to get 12v, to use as Honda Activa battery
@@idnetbox maximum capacity which is available in the market is 3500 mah. Standby capacity is 1800 mah to 2600 mah..but not the maximum capacity is 2600 mah.
Mere Bms board se output voltage nahi ara h mene negative ko short krke bhi dekha 3 bms board change kr diye connection bhi sahi h pr output nhi mil rha plz tell 🙏🏻🙏🏻🙏🏻
I made a circuit, with (3 Batteries + 10A BMS & XL6009) - working fine. Buit, the battery voltage is dropping automatically even if the input voltage is ON and is 12V. Why the battery voltage should drop ?? Where could be the problem ??
I submit that it is very misleading to imply a BMS can replace a proper charger Using a BMS ti charge Li-ion batteries can DAMAGE the batteries by shortening the discharge time and life of the battery. It SEEMS to work but you will be slowly DESTROYING it
Straight to point,with clear instruction!!!! THANKS!
how to charge? where do you plug the charger?
You Are The Best Presentation Of Proper Guidance. If You ADD Your Voice Then It's More Valuable 👌👌👌✅
Ok next time
Can we use this battery pack for charging and discharging at the same time as we see some fans are able to run while charging?
Yeah. You can. Because the voltage between output remains the same even though the batteries are low while connected to charger. Just make a try
Pode usar em paralelo até da 12 volts pra moto
NO you should discharge and charge the batteries FIRST before measuring the voltage
How to discharge battery?
@@yamraajji1086 google. use a low ohm high wattage resistor until voltage drops
to discharged voltage
@@yamraajji1086
Through using it
@@yamraajji1086Zbl23 module 😅
Best videos ❤❤❤
Hello sir. Made my own battery pack same as your presentation. Charged it perfectly for the first time then used it til it becam low battery. But upon charging, it wont charge. Whats the possible reason? I followed the same diagram as yours. Thanks
Check the battery voltage. If output voltage is less then 8.4v then might one cell damage. Then you need the removing all connection and check the 3 cell separately. Which battery cell voltage less than 2.4v you need to replace this battery another good one.. thank you
That spot welder is cool, how did you make it?
I buy it.
link please@@cubityt
Vaiya 20 a bms circuit a 3 ta 18650 battery use kora jabe???nki 6 tai korte hbe??
Can we charge this kind of pack with an ISDT Smart Charger without using balance plug ?
Can we use directly in bike to self start
What is backup capacity...?? While using 12v ??
How many hour to get fully charged
1hour
On the output dc jack we have to the charger wire?
Yes
@@cubityt can I attach normal phone charger?
@@sabirsheikh555from what I've seen in other videos you have to use 12.6 volt 2 amp charger.
C’est excellent merci pour l’explication
sir hm gastos po sa ganyan?
Does it work for Logitec UE MegaBoom 3 ... or do these only have 2x 18560 cells?
सर इस १२ वॉल्ट की बॅटरी को चार्ज करने के लिये bms को १२ वॉल्ट के लिये खेत का स्प्रे पंप का चार्जर १२वॉल्ट ८amp इस्तेमाल करे या मोटर सायकल की बॅटरी का चार्जर १२ वॉल्ट ४amp वाला इस्तेमाल करे?
Can i use this Battery pac as a ups for router?
@@তাইমুরশাওন yes sure
i want to make bt speaker with 6 inch subwoofer can i run this in this 3a battery
with 3s or 6s
we could be friends but you have this music so high xD
Bms can automatically off when it's full charge sir???
Yes brother ❤️
@@cubityt OMG a B
@@kennmossman8701 BMS is designed to cut off the charging voltage when the battery is full. This is an essential safety feature to prevent overcharging, which can damage the battery, create safety hazards, and reduce the battery's lifespan. The BMS monitors the voltage of the battery cells during charging, and when it detects that the cells have reached their maximum safe voltage level, it will disconnect the charging source to stop the charging process. BOKACHODA
Thanks bro want to ask the same question
@@cubityt where do you get this - try reading technical articles
show just one BMS datasheet that supports your claims - speficially that
-any bms will recognize all cells are fully charged
-the bms will turn off power from the charger
I will not wait because you wont find any.,
excelente amigo esta explicación fue la mas acertada ...saludos desde Suecia Estocolmo
Good information
Thank you
What's the BMS used for. Can this be done with 3 batteries without the BMS for a 12V hand drill?
Bms is a battery management system. without bms for example: when charging some cell are over voltage and some cell not fully changed. when discharging then some cell are fully discharged and other cell are not fully discharged.
@@cubitytis the BMS is over charging protection or auto disconnect?
Yes@@yamraajji1086
Se pueden coneptar 9 baterias de litoo de 3.7 v en paralelo con un tp 4056
can this module be charge again?
Voltag should be balanced. Same voltage or full charged
Do you recharge using the same output terminals by the DC jack? Thank you.
Yes. Same dc jack using for input and output
@@cubitytthen where to connect motor?
@@yamraajji1086 output terminal. check the bms first
Isko charge kese krna hoga
Completed wiring perfectly alright,on BMS,3స్,20A module, values are perfect but at out put getting 7.7 V only. What could be the reason bhai?
Check the individual battery first. If all battery voltage greater than 3.7v then use this battery for making a battery pack.
@@cubityt brother🙏with DMM measured voltages on BMS, 3S, 20A module as 3.83v, 7.3V, 11.36v, by placing DMM black probe at Ov. But the o/p is 7.7V only. I am using 6 batteries total, 2in parallel each(for high current), with 3 pairs to get 12v, to use as Honda Activa battery
Charge each and every batteries individually once all cells charged then use it
@@ramanavenkatamadala5543check the voltage of each and every cell separately
Good presentation, well done bro.
Mag kano po paassemble ng ganyan need q po yan 12v 3amp
Is it 3 a i don't think so.. they are in serial connection .. not parallel.. tell me when i m wrong
I think you don't notice my 18650 cell capacity. All three 18650 cells are above 3200 mah. That's why the battery pack is 3amp. Thank you dear.
@@cubityt oh ok is that real capacity ? Because as long as i knew each of them only have maksimum 2600 mah...
@@idnetbox maximum capacity which is available in the market is 3500 mah. Standby capacity is 1800 mah to 2600 mah..but not the maximum capacity is 2600 mah.
@@cubityt just suggestion from me.. would you like make a video with multitester for charging and discharging ? It is amazing video from you 🙏thanks
@@idnetbox ok dear..i will make it soon 🔜..
I have same spot welding machine, but not working. How you are giving supply to spot welding machine. ??
@@vikasazad08 you can use lipo battery more than 45c discharge rate for supply power.
sir 6 batteries ka kesy bany ga 12 volt output ke sath
What tape did you use??
Captain tape
Thank you
Welcome
Mere Bms board se output voltage nahi ara h mene negative ko short krke bhi dekha 3 bms board change kr diye connection bhi sahi h pr output nhi mil rha plz tell 🙏🏻🙏🏻🙏🏻
In that case you will charge this battery pack sometimes..then its start working
Bro what is this yellow tape you used and btw that spot welding looks really cool
Thank you brother 😊
Brother what was that transparent yellow tape u used
@@d4rks0ul_roblox Kapton Tape would be my guess.
Where i can get bms ?
You can buy this online or offline
Sana may link tsaka BMS ano sukat ng BMS
Si me contestan en español me gustaría que dijeran la referencia del modulo, gracias
Once its lowbat how you recharge it???
Output terminal also used for charging point.
What is the bms model?
3s 20amp
What type of Arduino do you use to solder the batteries?
Is it rechargeable??
Yes brother
@@cubityt can I plug it directly to my laptop charger?
I made a circuit, with (3 Batteries + 10A BMS & XL6009) - working fine. Buit, the battery voltage is dropping automatically even if the input voltage is ON and is 12V. Why the battery voltage should drop ?? Where could be the problem ??
Remove X L6009
@@cubityt why ? Many people have used XL6009 in their circuit and it works fine. Pl reply.
@@irapashunnur8237 Remove first and check.
are you using a PROPER charger? Is one cell defective?
Isko charge kese karna hai
How about 4battery 18650 parallel..😊😊😊
Output= 3.7v
@@cubityt yes 3.7v
Wht u recomend the protection bord in 4 battery parallel..
ini 12v kalau 3.7v 4 batrai bagaimana
Charger konsa lagega bhai
you can use any 12v ( 3A or 5A ) Adapter for charging
Bro, the bms is 3s ?
Yes brother
Bro, one last question bms 3s 20A or ?
And bms you buy from offline or online and price pls..
I order from electronic spices...
Rs 72/- 3s 20a per pc
Use 10 watt load backup time...?
That is NOT the proper way to measure battery voltage. There MUST be a load
But it is more convenient and work fine
@@Anubhav_hacker god help us the village idiot says it works fine
life saver! :)
👍✌️
How to 10.8v
It won't work I have already tried 😢😭😭😭
Sir ise bike me uge kar sakte he
For bikes, you need a minimum 10ah battery pack for good performance..
You can use it: ua-cam.com/video/vYwvAh0D2zA/v-deo.html
প্যারালাল দেখালি না কেন
hi
how to charge this battery you made?
For charging you need 12v adapter. Where we get output 12v the same terminal also used for charging.
Charging point
👍
3.7v,,9v
I submit that it is very misleading to imply a BMS can replace a proper charger
Using a BMS ti charge Li-ion batteries can DAMAGE the batteries by shortening the discharge time and life of the battery.
It SEEMS to work but you will be slowly DESTROYING it
😊
❤❤❤❤❤😮😮😮😮😮😮
4Vx3=12v
yes brother
Charger par video banao 12v Bms
Ok dear
when is 11.1 V the same as 12V? You get 11.1V and NOT 12V
Bhai aap kaha rahete ho
Not get 12v...only11.1v....3.7×3=11.1v
Probably not. These batteries can overcharge without any issue up to 4.2v.. most of them can do up to 4v.
4Vx3=12v
Yes,bro it maximum output is 4.2 volt and minimum is 2.4 volt so it can easily give 4 volt on more charge ❤❤
It is very importent and not mentioned that those batteries used has built-in circuit protections.
👍👍🏆🏆🇧🇷
Thank you
In out?
Input and output is the same port.
good
Is battery ko 12v inverter pe connect kr skte h kya