I just bought a 2014 Edge SEL, its a great SUV but lights the are DIM!! like your cousin who eats paint DIM!! i could not find a video to lign up the lights and adjust them properly, and then yours just popped up on my timeline! great video. Thank you, now i dont have to pay ford $400+
I just bought a 2014 Edge Sport December 2022 and everything runs very good...the info you shared on the LED installation was very precise and clear...is why i just subscribed...Thank you and look forward to more info on the links here ...PS: These Edge Sports are very nice even if Pre-owned 🙂 👌
This is great! It cost me over $300 at the dealer to get my headlights replaced 😵💫 Thank you for showing me that I can do it myself! I’m very happy to get some LED lights as well.
I assume for the lights & labor? If that's labor only, that's INSANE! This shouldn't cost more than $40 install / labor. Informative vid, but these LED's are not very bright at all. Hard pass on this brand!
Thank you for demonstrating how simple it is to accomplish. LASFIT 2022 New 9012 HIR2 LED Bulbs 6000K White, plug and play, and easy to adjust from Amz! Perfect for my MKX 2013 (going on 4 months now.)
Any concern with the heat from the led inside the headlight housing? I'm about replace mine and am curious if it'd be beneficial to drill a couple holes in the cap?
These bulbs may get hot.... can you put the cover back on the enclosure ? Wouldn't the fan require leaving the cover off ? The cover protects from moisture though so not sure how it all works out ?
@@6thGearGarage you're simply circulating hot air though with the covers on tho...although, I'm not sure I would leave the covers off & run the risk of moisture in my housing. Might depend on where you live and how often you drive in the rain / snow, etc.
Nice video. Did you notice any flickering or warning light on the dash. I want to make the changeover to LEDs. Just wanted to know if I would have to install warning cancellars/ resistors.
We don't have this vehicle any more, but they worked great until the engine went. I took the bulbs out and saved them in case I ever have another vehicle that can use them .
these are OK bulbs if you're on a budget. They will be better than stock, but not much better about a year later. I ran these for about 16 months and they were pretty good for the 1st 6 - 8 months. There are much better bulbs out there between $50-$80. Unless this is all you care to spend, I'd pass on these!
According to other videos they dont put the dust cover back on or they put holes on it because led lights get hot and it affects the output of the light.. you put it back on is it ok? Will it not be too hot with the cover? Thanks...
I just bought these for my 2013 edge! I purchased the ones from your link. Thanks! Just to make sure, the bulbs come with the connector and I don't have to purchase anything else for these to work? I've never had LED headlights before. Thanks again for your video!
Awesome video, I have a 2013 Ford Taurus, used 9012 LED's and they did the job perfect, they are in the same housing as the ford edge! Appreciate the help!
Do people flash you? Or did you need to adjust the bulbs down? I have had to adjust my LED retrofits down so as to not annoy other oncoming drivers with different manufacturers bulbs.
@@6thGearGarage yes everything is the same, the thing is when I bought the SUV it came with some aftermarket xenon light and they really suck, hope you could tell if this LED look good under rain or snow?
I have the same 2011 Edge, and my halogen projectors come on with the DRL. Have you noticed any issues with this? Are the LED's crazy bright when running as DRL?
I have not had any issues with DRL, as I never used them or the vehicle didn't have them. I don't think the LED's would cause a problem being used as DRL's.
@@6thGearGarage I thought daytime running lights were standard, they just make the projector headlights come on at a slightly dimmer level during the day. Anyway, I ordered and installed the exact same LED's on my Edge about a week ago, and can confirm that the DRL's work correctly, with no flickering or any other issues. If I were to do it again, I'd probably look for some that have 4 LED's instead of 2. The projector housing was made for 360 degrees of light, and the dual LED has a blind spot parallel to the plane of the aluminum mount. That's why they need to be rotated, the light drops off in these areas. It's still much better than the halogens. Thanks for your video!
Question: How did you secure the bulb position once you adjusted it properly? I mean, can't the bulb still rotate, if you don't do anything? Cars vibrate a lot while driving. Also, I see 9005 + H11 as the recommended bulb for the 2011 Ford Edge. Is that the same as the 9012?
The position stays put and hasn't moved from vibrations so far. I suppose there's enough tension to keep it from rotating on its own. I know there are HID headlights available for the Edge that use a different bulb, but as far as I know, the halogens for this generation of Edge are a 9012 bulb. You may want to check Lasfit's website before buying.
The 9005 and 9006 are very similar to the 9012 and can be used. The pegs for securing it in the housing are a little different and will work. If you are having trouble you can cut some plasic off the bulb base. The plugs are the same. No adapter needed.
So what aim I doing wrong I have 2011 MKX and my plug in plug on my headlight does not look like the one your showing in the video. It's much smaller and a light blue in color. Any help will be much appreciated.
Can someone with a ford edge 2013-2014 tell me if your car use headlight bulbs with the 9012 code or the 9006 , i just want to know if my bulbs are original form the dealer o someone changed them before i bought it , thanks
Hi there, i'm from Switzerland and i like to order such Bulbs. Can you please send me the exact product details, product number, etc. so that I can order them? Maybe you also have a link directly? Thank you and best regards
@@mikerock8177 thanks I took the wire (plug into the balast) connected it and the led wire using an easy connector and didn't get power. Unless I used the wrong 2 wires from the balast (has a black, teal, and brown wire). The led wire was only + and - (black and red)
Hey, can you tell me if the stock HID bulbs are twist / lock to remove and install them ? I can't find any good info for our model years ( I have 2014 ). Thanks 👍🏻
I have not considered upgrading the vertical fog lights on this model. They don't really put out as much light as a traditional fog light, probably because they're so thin. I'll have to see if there's a way to make them brighter with a different bulb.
6th Gear Garage awesome thanks! Most of the aftermarket one out there do not offer extra projection. It would be awesome if there was a plug and play option for seeing around corners on dark streets. Looking to buy those exact LED lights since I know the beam pattern will look good. Are you still happy with your purchase?
Man I just tried installing my bulbs. One bulb worked for my passenger side but the other didn’t work for my D/S. So I switched them out and neither one came on. So obviously there is something going on with my D/S as well as a dead bulb. All in all a complete bummer! Only one bulb works and only on the P/S. 😒
I just took them to the UPS store to return earlier today and already got my refund. Maybe I’ll try ordering them again. I just thought maybe there was a compatibility issue with the D/S and an LED bulb.
does anyone want to talk about how bad the edge headlights suck mainly for driving down dark country roads? i tried LED and i went back with the best sylvania halogens because while the LED may be brighter in terms of lumens and color temp, the halogens were better focused. i guess its the way led light disperses or something but no matter what bulb you use the headlights suck bad just look back when you turned your brights on, i could hardly tell, if the video had been muted and i had to guess i would have thought you didnt even turn them on. i have adjusted the headlights up and down on a dark road at night and got them out as far as they could reach, there is no side to side adjustments for those who are asking. there has got to be a way to make these headlights not really so much brighter but get further down the road and yeah maybe brighter to. my 03 explorer low beams outshines the edges high beams by a country mile.
@@6thGearGarage if you know of any mods or something to make these lights better please share, thanks for the video upload and best of luck to you if you still own that car.
@@davidkanoff110 I think some had an option for Xenon/HID headlamps. Perhaps they could be retrofitted? Although I've never compared the output difference, so it may not be worth it. At 180k mi, The water pump went out while driving on the highway, so I parted out our ford edge.
@@6thGearGarage I replaced the water pump on mine at 260k and it went out again a year later and had to change it again. Yes I did the work myself, it's a pain, that's why they charge so much for such a cheap part.
This is the best headlight aiming video on UA-cam. It's the only one that shows how to manage the pattern of the light.
I just bought a 2014 Edge SEL, its a great SUV but lights the are DIM!! like your cousin who eats paint DIM!! i could not find a video to lign up the lights and adjust them properly, and then yours just popped up on my timeline! great video. Thank you, now i dont have to pay ford $400+
I just bought a 2014 Edge Sport December 2022 and everything runs very good...the info you shared on the LED installation was very precise and clear...is why i just subscribed...Thank you and look forward to more info on the links here ...PS: These Edge Sports are very nice even if Pre-owned 🙂 👌
LOVE my '14 SPORT. A few upgrades & a tune & it comes ALIVE!!!!
This is great! It cost me over $300 at the dealer to get my headlights replaced 😵💫 Thank you for showing me that I can do it myself! I’m very happy to get some LED lights as well.
Glad I could help
I assume for the lights & labor? If that's labor only, that's INSANE!
This shouldn't cost more than $40 install / labor.
Informative vid, but these LED's are not very bright at all. Hard pass on this brand!
Fantastic video, I drive a 2013 Ford Edge and your instructions were very clear. I appreciate the video.
Fantastic comment, I drive a 2012 Ford Edge and your comment was very nice. I appreciate the comment.
@@kingtownley1226can you show the upgrades and especially the tune?
Thank you for demonstrating how simple it is to accomplish. LASFIT 2022 New 9012 HIR2 LED Bulbs 6000K White, plug and play, and easy to adjust from Amz! Perfect for my MKX 2013 (going on 4 months now.)
What clock do they go or just adjust till looks good
I don't think there's an exact amount... I just adjusted until they looked good.
Fantastic tutorial.you get to the point of the matter.Thank you so much.Greetings from. Merida Yucatan Mx. 15 Dec. 2023.
Dude you saved us a ton of $$
Thank you for your awesome video 👍🏽 My 2012 Edge never looked ( or I can see😉) better!
Any concern with the heat from the led inside the headlight housing?
I'm about replace mine and am curious if it'd be beneficial to drill a couple holes in the cap?
No concern at all. Actually, these led bulbs make a lot less heat than the oem halogen bulbs did.
Thank you for doing the driver side! I too dropped my dust cap but my hands were too fat to get the bulb out? Do I need to drop the bumper to do this?
The bumper is flexible enough that maybe you can bend the bottom down a little to get your hand in? It’s a bit of work
to remove the bumper.
for someone like me who hardly works on the car, your video made this a super easy install, guess i will subscribe to keep an eye on for whats next
These bulbs may get hot.... can you put the cover back on the enclosure ? Wouldn't the fan require leaving the cover off ? The cover protects from moisture though so not sure how it all works out ?
I don't believe LED Bulbs get hot like Halogen bulbs do. I think the fan is enough to keep them cool within the enclosure with the cover.
@@6thGearGarage you're simply circulating hot air though with the covers on tho...although, I'm not sure I would leave the covers off & run the risk of moisture in my housing. Might depend on where you live and how often you drive in the rain / snow, etc.
Will these bulbs work in a vehicle that has daytime running lights? Thank you.
I don't know for sure, as I haven't tried. You may want to contact Lasfit or check on their website to be sure.
Nice video. Did you notice any flickering or warning light on the dash. I want to make the changeover to LEDs. Just wanted to know if I would have to install warning cancellars/ resistors.
There is no flickering or warning lights on the dash. These are a true plug and play bulb for the Edge.
Ok so no coversion at all just plug and play. Perfect. Thank you
I purchased a set with the capacitors. Would this cause the lights to not be as bright? Do you need capacitors for the edge?
I did not need the capacitors. I've seen some that came with noise filters but I did not need those either.
@@6thGearGarage ty for responding.
Still enjoying the HID bulbs. LEDs have come a long way. How is the life span?
We don't have this vehicle any more, but they worked great until the engine went. I took the bulbs out and saved them in case I ever have another vehicle that can use them .
these are OK bulbs if you're on a budget. They will be better than stock, but not much better about a year later. I ran these for about 16 months and they were pretty good for the 1st 6 - 8 months. There are much better bulbs out there between $50-$80. Unless this is all you care to spend, I'd pass on these!
maybe cover getting the clips on the bulb to release. I got it but some may need it
i am fixing to be helping a friend do this. how do you think the diodes are sitting? at 6 and 9 or something else? thank in advance.
To be honest I don't remember and this vehicle isn't here anymore. Parking in front of a garage door is the best way to fine tune the adjustment.
According to other videos they dont put the dust cover back on or they put holes on it because led lights get hot and it affects the output of the light.. you put it back on is it ok? Will it not be too hot with the cover? Thanks...
manoy Q led bulbs produce less heat than halogen bulbs. I haven’t experienced any issues so far. 👍
Ok but they say led headlight bulb gets so hot that is why they have cooling fans
Unfortunately nobody deliver to Switzerland. Do you know any similar products i could use?
Have you checked ebay and amazon?
I just bought these for my 2013 edge! I purchased the ones from your link. Thanks! Just to make sure, the bulbs come with the connector and I don't have to purchase anything else for these to work? I've never had LED headlights before. Thanks again for your video!
Yes they do, they are plug and play, nothing else is needed.
Any problems faced after installing yet?
Thanks! Will be changing mine soon
Awesome video, I have a 2013 Ford Taurus, used 9012 LED's and they did the job perfect, they are in the same housing as the ford edge! Appreciate the help!
Good to know they're the same - thanks!
Hey my friend got a quick question how do you adjust the headlights left to right on a edge 2013?
I don't think they are adjustable left to right, only up and down.
Yup ... Dropped the cap... Fished it out... All good.... Thanks for the video... Headlights lookg great
What stops the led bulbs from turning after you adjust them. Others have a Allen screw to lock in position
There seems to be enough tension to keep it from rotating on its own. I've had these for a couple of months so far with no problems.
Do people flash you? Or did you need to adjust the bulbs down? I have had to adjust my LED retrofits down so as to not annoy other oncoming drivers with different manufacturers bulbs.
I have not been flashed yet. The OEM projector housing headlight design of the Edge has a nice cutoff line.
What about the key? what is the position of the notches
The light installs all the way in the notches like a normal bulb
So it doesn't need any kind of anti flicker system?
Nope, I just installed the bulbs and that was all I needed to do.
@@6thGearGarage awesome thanks for that info and video.
Would these headlights work on a 2011 explorer??
Pebble the Testicle im. It sure but if you go to lasfit’s website, they tell you which bulbs fit your vehicle.
I have xenon on my 2012 and they are terrible, can you tell me how this work?
I don't know if the LED bulbs will fit in the xenon headlamps. Are they the same as the halogen headlamps?
@@6thGearGarage yes everything is the same, the thing is when I bought the SUV it came with some aftermarket xenon light and they really suck, hope you could tell if this LED look good under rain or snow?
@@irvinglechuga2067 I'm very happy with the LED, it was better in every scenario.
How do you change the front blinker lightbulbs on a 2011 lincoln mkx?
I don't have one to show, sorry
How do you adjust side to side?
I don't believe you can.
Ok. I thought it could be done. Thanks.
I have the same 2011 Edge, and my halogen projectors come on with the DRL. Have you noticed any issues with this? Are the LED's crazy bright when running as DRL?
I have not had any issues with DRL, as I never used them or the vehicle didn't have them. I don't think the LED's would cause a problem being used as DRL's.
@@6thGearGarage I thought daytime running lights were standard, they just make the projector headlights come on at a slightly dimmer level during the day. Anyway, I ordered and installed the exact same LED's on my Edge about a week ago, and can confirm that the DRL's work correctly, with no flickering or any other issues. If I were to do it again, I'd probably look for some that have 4 LED's instead of 2. The projector housing was made for 360 degrees of light, and the dual LED has a blind spot parallel to the plane of the aluminum mount. That's why they need to be rotated, the light drops off in these areas. It's still much better than the halogens. Thanks for your video!
They really are good quality!
Thanks for sharing 😊
Where is the linknfor the specific light bulb ??🤔🤔🤔
It’s in the description
How do I adjust my 2013 Edge headlights side to side
josh resteman I’m not sure they can be adjusted side to side, only up and down.
Well I'm sold!
What about the power it sam watts or ?
Led draws less power than halogen bulbs.
Question: How did you secure the bulb position once you adjusted it properly? I mean, can't the bulb still rotate, if you don't do anything? Cars vibrate a lot while driving. Also, I see 9005 + H11 as the recommended bulb for the 2011 Ford Edge. Is that the same as the 9012?
The position stays put and hasn't moved from vibrations so far. I suppose there's enough tension to keep it from rotating on its own. I know there are HID headlights available for the Edge that use a different bulb, but as far as I know, the halogens for this generation of Edge are a 9012 bulb. You may want to check Lasfit's website before buying.
The 9005 and 9006 are very similar to the 9012 and can be used. The pegs for securing it in the housing are a little different and will work. If you are having trouble you can cut some plasic off the bulb base. The plugs are the same. No adapter needed.
So what aim I doing wrong I have 2011 MKX and my plug in plug on my headlight does not look like the one your showing in the video. It's much smaller and a light blue in color. Any help will be much appreciated.
Some of the MKX use a xenon bulb, is that what yours has?
thanks. this was helpful to find a good plug and play light: they also happen to have a veteran's day coupon code rn. we'll see how it goes.
how about for hilux rogue it is the same way with ford because my truck it right side blow out already
I'm not familiar with hilux rogue, as they were never offered in the US.
Oic....that o.k sir thanks for replay my mesej😬👍
9012 is original...but how this especification for this lights?
Hi, I put a link in the description with all the specs.
Can someone with a ford edge 2013-2014 tell me if your car use headlight bulbs with the 9012 code or the 9006 , i just want to know if my bulbs are original form the dealer o someone changed them before i bought it , thanks
9012/HIR2
Hi there, i'm from Switzerland and i like to order such Bulbs. Can you please send me the exact product details, product number, etc. so that I can order them? Maybe you also have a link directly? Thank you and best regards
Just found the link. Thank you very much for that nice video. Greetings from Switzerland.
Hi does this number work for low and high beam? Or, is there a different number for the low beam? Thanks
Hi, I’m not sure, as these are direct replacements for the oem bulb, which controls the hi and low beams.
Yes
Really helpful😳
Excellent tutorial dude. Cheer s
Where is the flush relay located in 2013 Ford Edge se
I am not sure, sorry
Oo bro i wish i saw this earlier..i just replaced those with sylvania silverstar ultras
How do you like the sylvania silverstar ultras compared to the original bulbs?
@@6thGearGarage they are brighter and have more light then oem.. but not that white as i wanted
2013 limited bulbs are deferent and will not work just a heads up.
Are those the HID headlights? These bulbs will not work in the HID headlights, only halogen.
Thank you for this video
Thank you!!
I converted my 2013 Ford Edge to all LEDs the car headlights where are HID converted them to LED with no wire conversion kit necessary
@mike rock Do you care to share how you accomplished this. My edge came equipped with HID
@@nevinwatson9538 no problem the wire that plugs into your hid Blaster I guess you call it is the same wire you need for the headlights
@@mikerock8177 thanks I took the wire (plug into the balast) connected it and the led wire using an easy connector and didn't get power. Unless I used the wrong 2 wires from the balast (has a black, teal, and brown wire). The led wire was only + and - (black and red)
@@nevinwatson9538 it should work one is a control wire i think keep work on it worked for i no problem i to used plung an play leds
Hey, can you tell me if the stock HID bulbs are twist / lock to remove and install them ? I can't find any good info for our model years ( I have 2014 ). Thanks 👍🏻
This is awesome. You you consider fog legs too? I live in some dark roads and cannot see when turning with my factory Edge
I have not considered upgrading the vertical fog lights on this model. They don't really put out as much light as a traditional fog light, probably because they're so thin. I'll have to see if there's a way to make them brighter with a different bulb.
6th Gear Garage awesome thanks! Most of the aftermarket one out there do not offer extra projection. It would be awesome if there was a plug and play option for seeing around corners on dark streets. Looking to buy those exact LED lights since I know the beam pattern will look good. Are you still happy with your purchase?
DMONICUS6 thanks dude. I’ll check them out!
Best video for this job.
Wow, thanks
Man I just tried installing my bulbs. One bulb worked for my passenger side but the other didn’t work for my D/S. So I switched them out and neither one came on. So obviously there is something going on with my D/S as well as a dead bulb. All in all a complete bummer! Only one bulb works and only on the P/S. 😒
I wonder if there is a wiring problem or short on the driver side that damaged the bulb. Did your OEM bulb work ok?
Yeah I put the bulb that I already had back in and it worked with no problem. Strange. I was pretty bummed about it.
@@wan2865 If it was from Lasfit, I would contact them for a replacement.
I just took them to the UPS store to return earlier today and already got my refund. Maybe I’ll try ordering them again. I just thought maybe there was a compatibility issue with the D/S and an LED bulb.
Nicely done, thanks
I have it on my Ford Edge 2012 is pretty good! But I'm going to replace it with the new Morimoto 9012 2 stroke 3.0
How was it??
Wish you had driving video before the change....
I would have but one bulb was already burned out.
does anyone want to talk about how bad the edge headlights suck mainly for driving down dark country roads?
i tried LED and i went back with the best sylvania halogens because while the LED may be brighter in terms of lumens and color temp, the halogens were better focused.
i guess its the way led light disperses or something but no matter what bulb you use the headlights suck bad just look back when you turned your brights on, i could hardly tell, if the video had been muted and i had to guess i would have thought you didnt even turn them on.
i have adjusted the headlights up and down on a dark road at night and got them out as far as they could reach, there is no side to side adjustments for those who are asking.
there has got to be a way to make these headlights not really so much brighter but get further down the road and yeah maybe brighter to.
my 03 explorer low beams outshines the edges high beams by a country mile.
Yeah, they were never that great compared to some other vehicles we've had.
@@6thGearGarage if you know of any mods or something to make these lights better please share, thanks for the video upload and best of luck to you if you still own that car.
@@davidkanoff110 I think some had an option for Xenon/HID headlamps. Perhaps they could be retrofitted? Although I've never compared the output difference, so it may not be worth it. At 180k mi, The water pump went out while driving on the highway, so I parted out our ford edge.
@@6thGearGarage I replaced the water pump on mine at 260k and it went out again a year later and had to change it again. Yes I did the work myself, it's a pain, that's why they charge so much for such a cheap part.
The ones I was sent didn't fit my edge.
What did they say when you contacted them?
They are sending me a return label.
Oh, they also said to try the gasket off of my old halogen bulb, but it dosent come off so...
@@rickybobby6678 Ok glad they took care of it, I always found their customer service helpful.
Yah but!! You didn't show how to replace the drivers side bulb. TOTAL PIA! No hand room. I thing the fuse box has to come off.
Yeah I did, you gotta watch the whole video ;) And yeah, it's a tight fit.
@@6thGearGarage OK...
I just change my lights on both side without removing the bumper cover
Only difference I seen is one is yellow light and the other white .
Polis
Head lamps
Fix dull head lsmps
These bulb are so dim in projector headlamp
2011 model year and FORD and other copycats STILL charge 20K,30K+, and DARE TO GIVE CUSTOMERS 1950 STYLE BULBS!!! DAMN THEM ALL!!!!
Yep, At lease the LED upgrade is simple to do!
"Dont touch the glass on the bulb, it will shorten the life..." 2 seconds later, throws bulb straight in trash.
That bulb was burned out. I did keep the other one in case one of the LEDs ever goes out.
LED offer less performance than halogen 😆
If that is true, then why are automotive manufacturers phasing out halogen lighting for LED?