Repair was possible in this way particularly because it's a four jaw chuck. If it were a three jaw chuck, the position (the phase) of the threads had to be adjusted in some way depending on which jaw it was to ensure that all the jaws have the grabbing surface at the same distance from the center.
That's the problem I've got! My brother broke my internal jaw set and stripped half the thread off one of them - I can still use it but only for certain diameters
those who say this is good work do not understand machining. All this work and a few steps in measurement could have produced a decent repair. He cut way too deep with the threads. He should have gone to a specific depth with the initial boring operation for the minor diameter of the thread and verified with a micrometer. this number could have been taken from one of the other jaws. then while cutting the thread , he should have been dialing in to a number, while placing the screw in the jaw until the number matched perfectly again checking with a micrometer measuring the screw placed in the thread to the opposite side of the jaw after verifying distance to the side slot. Every thing comes off that side slot he didnt even indicate the jaw prior to machining. this guy actually was using a disk grinder on the flat side of the jaw after welding. thats the whole precision of the chuck. notice how they didnt show You how it fit into the chuck after repair so we could really determine the quality of the repair. All this work and for 10 percent more time it could have actually been done right. You are not fooling Me with this bad work
This is a good job! Thank you for sharing your experiences I appreciate.
Repair was possible in this way particularly because it's a four jaw chuck. If it were a three jaw chuck, the position (the phase) of the threads had to be adjusted in some way depending on which jaw it was to ensure that all the jaws have the grabbing surface at the same distance from the center.
Кулачки можно расточить, потом фрезеровать угол и всё
That's the problem I've got! My brother broke my internal jaw set and stripped half the thread off one of them - I can still use it but only for certain diameters
Que soldadura aplico
You are working super excellent 👌👍
Masallah zbrdst great 👍
Thanks sir 🙏
أللهم صلى وسلم وبارك على نبينا وحبيبنا محمد صلى الله عليه وسلم ❤
those who say this is good work do not understand machining. All this work and a few steps in measurement could have produced a decent repair. He cut way too deep with the threads. He should have gone to a specific depth with the initial boring operation for the minor diameter of the thread and verified with a micrometer. this number could have been taken from one of the other jaws. then while cutting the thread , he should have been dialing in to a number, while placing the screw in the jaw until the number matched perfectly again checking with a micrometer measuring the screw placed in the thread to the opposite side of the jaw after verifying distance to the side slot. Every thing comes off that side slot he didnt even indicate the jaw prior to machining. this guy actually was using a disk grinder on the flat side of the jaw after welding. thats the whole precision of the chuck. notice how they didnt show You how it fit into the chuck after repair so we could really determine the quality of the repair. All this work and for 10 percent more time it could have actually been done right. You are not fooling Me with this bad work
Good repairing on lathe chuck jaw threads keep it up
V.good work
Good work.
Thanks
Ma Sha allah bhot ache
это сколько надо здоровья иметь или каким дрыном тянуть,чтоб кулачок сломать😮😮😮
Они же кувалдой там колотят когда центруют
@timirlan1504 да я как бы сам с кувалдой не стесняюсь,но чтоб ломать такого не было
@@ГригорийГолдышев-т7й А вы другие ролики посмотрите как они кувалдами колотят по детали)))
@@timirlan1504 это их проблемы,сам шпиндель с подшипниками спасибо не скажет.
Good work
How DF did that happen
Repeated use of a 3 feet pipe to tighten.
V.good technic
Great work
Thanks
Ye aaj se... 6 saal pehele.... Bana chuke...
Cara memperbaiki larapan bubutan yang sudah aus
🎉🎉🎉🎉🎉🎉🎉🎉
Ну нечего страшного скоро очередной ремонт! Они же любят кувалдой колотить по деталями
И заготовку зажимать трубами и ломами.
шайтаны