Holset HX40 Turbo Rebuild -Turbo Lab

Поділитися
Вставка
  • Опубліковано 23 січ 2025

КОМЕНТАРІ • 54

  • @jmerchant79
    @jmerchant79 9 років тому +37

    how drunk were you when you made this video lol

  • @Timeatkmaro
    @Timeatkmaro 7 років тому +1

    Thanks so much for this! Just put your kit on my HY35 that's on my civic. Install was simple and so far no more smoking.

  • @theletterl8948
    @theletterl8948 2 роки тому

    AWESOME That dude can really put the Hick in Hick up!!! Thanks brother you really help me out with your video I went smooth and worked killer. Thanks again.. High fives from Joe in Alaska...

  • @alanbehnke9615
    @alanbehnke9615 7 років тому +16

    I tried to watch this but I couldn't stop laughing. I hate the hiccups.

  • @davidcrowell5515
    @davidcrowell5515 3 роки тому

    Where does the small rubber oring go in the hx35w turbo lab kit

  • @scopes331
    @scopes331 7 років тому

    Do you know if the hx40w will simply bolt on in place of the hx35w? I understand that as long as the exhaust housing T3 it should bolt up but I mean the oil feed line and oil drain line. I know I'd need a down pipe as well

  • @Playtuviu
    @Playtuviu 4 роки тому

    Obrigado pelo vídeo, ótimo conteúdo, não entendo oque vc fala, mas aprendi muito, pois ficou ótimo o video, vou desmontar minha turbina e ver porque está vazando óleo na parte do compressor, obrigado
    Likeeee 👍

  • @OCD_FPV
    @OCD_FPV 5 років тому

    What are doing as far as balancing the assembly?

    • @turbolabamerica
      @turbolabamerica  5 років тому

      I use a west coast balancer. It’s like the Hines model 30. You don’t have to balance the assembly on the Hx40. They are just balanced individual pieces

    • @OCD_FPV
      @OCD_FPV 5 років тому

      Great information thank you!

  • @jorgefonseca9225
    @jorgefonseca9225 8 років тому

    my suburban 6.5 lost power and i think i change the turbo and i would like put a more power on it i have idea buy a holset HX40 what you recomend me? is a good idea put a hx40

  • @TheRealKnownEnemy
    @TheRealKnownEnemy 9 років тому

    The holes in the thrust bearing that are sometimes too small; what is the proper diameter of them?

    • @turbolabamerica
      @turbolabamerica  9 років тому

      +Donnie Stritzinger I never measured them before. I'm not sure how to measure that. I guess I can measure where the bearing is drilled on the outside.

    • @TheRealKnownEnemy
      @TheRealKnownEnemy 9 років тому

      +Turbo Lab America that would be a real help. Thanks, in advance.

    • @boosttapperformance8673
      @boosttapperformance8673 7 років тому

      Turbo Lab America is the center cartridge of the HX35W the same as the HX40W?

  • @1989rrichard
    @1989rrichard 10 років тому

    Hey where can I get the char my fins are chip and I need to replace that too I have hx40

    • @turbolabamerica
      @turbolabamerica  10 років тому

      You need the whole cartridge? Or just the compressor wheel. I have all the parts to make you a cartridge. I need to know the measurement of your wheel and the blade count.

    • @1989rrichard
      @1989rrichard 10 років тому

      7 blade and I currently have it in a 55 ar dsm housing

    • @1989rrichard
      @1989rrichard 10 років тому

      I can send u info later when I get home can I find u on favebook?

    • @turbolabamerica
      @turbolabamerica  10 років тому

      Leave me a message here: facebook.com/TurboLabAmerica and ill get back to you.

  • @kamolia
    @kamolia 6 років тому

    Hello Austin, I was trying to rebuild my hx35 but the kit I bought came with only 1 turbine end piston ring whilst my turbine shaft requires 2 piston rings, I can't seem to find anyone selling piston rings here in UK for the Holset, can you tell me if the piston ring from the hx35 is interchangeable with another from say a garret GT series or any TD because these are available here, also can you please tell me what do you think of stepped gap piston rings and are they useable in the Holset application

    • @turbolabamerica
      @turbolabamerica  6 років тому +1

      The models that have the 2 piston rings use 2 of the same standard size rings which the gaps need to be 180 degrees apart. You can use the staggered seal. I don't have a preference of the staggered one over the standard one. The seal only leaks when the sides of the seal where out unless there is build up of oil in the cartridge where it's pressurized and forced out of the seals

    • @kamolia
      @kamolia 6 років тому

      Turbo Lab America thank you ever so much

  • @jorgefonseca9225
    @jorgefonseca9225 8 років тому

    nice vedeo mate good work regards from norway

  • @Alexlachica37
    @Alexlachica37 8 років тому

    what the torque special on wh1c turbo please?

    • @turbolabamerica
      @turbolabamerica  8 років тому

      +Kennygsx on the compressor nut?

    • @Alexlachica37
      @Alexlachica37 8 років тому

      +Turbo Lab America
      yes the locknut for the compressor wheel torque spec.
      I just bought one your rebuild kit and everything works great. thanx

    • @turbolabamerica
      @turbolabamerica  8 років тому

      Put the nut on by hand then when the nut starts to tighten add 1/4 turn. Torque spec on the mhi 6.5 mm shaft is 7 ft lbs. the Holset is 7mm bore. So the spec will be close the that. I want to check with a torque are here to confirm. I have one turbo here that the guy tightened the compressor nut so tight that the nut is fused to the compressor wheel.

  • @brunopinhoputo5344
    @brunopinhoputo5344 9 років тому

    Do not need calibration?

    • @turbolabamerica
      @turbolabamerica  9 років тому +2

      Bruno Pinho puto If you are talking about in terms of balancing, no. The Newest HX and HE turbos with the 12 point 10mm nut are component balanced parts and the Holset turbos with the 6 point nut are rotor balanced according to the Holset Service manual.
      The Turbos with the 6 point nut should be realigned to the factory balance marks. The Holset Turbos with the 12 point nut can be aligned at any rotation, because the parts are balanced at any rotation.

  • @1989rrichard
    @1989rrichard 9 років тому

    u happen to have any hx40 6 blade 60mm compressor wheel for sale I need one

    • @turbolabamerica
      @turbolabamerica  9 років тому

      +Richard Reid You can get one here ebay.to/1OJMBHZ Just Keep in mind that the 6 blade has a taller tip height than the 7 blade, so the 6 blade is not a direct fit for the 7blade compressor housing. Also there is a 56 x 83mm 6 blade too, so make sure you measure your compressor wheel or check your part number to double check.

  • @laminebenamine9023
    @laminebenamine9023 7 років тому

    Hello! what is difference between holset hx40 & hx40 super

    • @turbolabamerica
      @turbolabamerica  7 років тому +1

      +lamine ben zina factory billet wheel which weighed the same as the stock one and it had a 10 blade 64 x 76 turbine vs a 12 blade

  • @46p.o.s.notmypresident41
    @46p.o.s.notmypresident41 5 років тому

    thanks austin u rock

  • @CumminsDslPwr
    @CumminsDslPwr 10 років тому +13

    Are the hiccups required to complete the rebuild? ROTFLMAO

    • @rbvb7539
      @rbvb7539 3 роки тому

      Absolutely I think the same ....

  • @schnabulator6436
    @schnabulator6436 7 років тому +2

    Thanks for the video.
    I heart that Holset turbos are not balanced as an assembly.
    Is that true?
    And when yes, why is that not necessary?
    Best regards from Germany

    • @bent_rods
      @bent_rods 7 років тому

      if the bolt is a typical hex then it needs to be rebalanced after building. It is is the 13point style nut,then they are intenally balanced.

  • @Coralrockplumbing
    @Coralrockplumbing 7 років тому

    very good video, can send ours over for a rebuild?

  • @9076723311
    @9076723311 8 років тому

    good video though. helped me with my kit. thanks.

  • @notsogreat123
    @notsogreat123 4 роки тому

    I'm glad there were no HICCUP's in this install ;-)

  • @EIAdventures
    @EIAdventures 3 роки тому

    Ok I have a video on how to rebuild a nasa booster motor. Just put all the new parts in the old shell. That's it.

  • @ameirabbden5290
    @ameirabbden5290 6 років тому +1

    Man,i hate those scums criticized things this dude does,what tools he has and what wrong he did..make your own then show us..if it works then great for u,good job..

  • @9076723311
    @9076723311 8 років тому

    FYI, those are snap rings not "c" clips. you don't use snap ring pliers on "c" clips.

    • @ameirabbden5290
      @ameirabbden5290 6 років тому

      Brian McNeil,it's all about the handjob bro,as long it works..u can even tight a M16 bolts using a hammer if got the skill..

    • @46p.o.s.notmypresident41
      @46p.o.s.notmypresident41 5 років тому

      so where the fuk is your video,,,austin does a fine job,,,why dont you just go read a book instead to learn something,,??if u can read,,,lol

  • @turbolabamerica
    @turbolabamerica  10 років тому

    If you need the rebuild kit for the hx40 hx35 here is : amzn.to/1CXDz3A

  • @nickadcock7296
    @nickadcock7296 3 місяці тому

    Couldn't watch entire video. Wonder if hiccups lasted till the end.

  • @radupaul78
    @radupaul78 9 років тому

    9:27 fail

  • @qaderjumaah5876
    @qaderjumaah5876 8 років тому

    we play drinking game ,every time you have hicap we take shot ,

  • @notsogreat123
    @notsogreat123 4 роки тому

    Maybe a couple tums would have helped this install ?

  • @Stacy24910
    @Stacy24910 7 років тому +2

    Boo!