How to Replace Front Lower Control Arm 11-15 Chevy Cruze
Вставка
- Опубліковано 30 січ 2020
- Buy Now!
New Control Arm with Ball Joint Set from 1AAuto.com 1aau.to/ia/1ASFK00767
Control arms are a crucial part of the suspension system of your vehicle. They not only carry the load of the vehicle to the wheel, but they typically also maintain its alignment. Control arms are typically large and strong, so you may be surprised it needs replacing. They contain rubber bushings for smoother rides at the cost of eventual wear. This video shows you how to install a new quality TRQ lower control arm in your 2011-15 Chevy Cruze.
• Check here for more videos on the 2008-16 Chevy Cruze: ua-cam.com/users/playlist?list...
This process should be similar on the following vehicles:
2011 Chevrolet Cruze
2012 Chevrolet Cruze
2013 Chevrolet Cruze
2014 Chevrolet Cruze
2015 Chevrolet Cruze
Tools you will need:
• Pry Bar 1aau.to/ons/1AXAA00020
• 15mm Wrench 1aau.to/on7/1AXAA00010
• 18mm Wrench
• 15mm Socket 1aau.to/oSs/1AXAA00015
• 18mm Socket 1aau.to/ous/1AXAA00043
• 19mm Socket 1aau.to/ous/1AXAA00043
• 7mm Socket 1aau.to/oLi/1AXAA00017
• Dead Blow Hammer 1aau.to/oou/1AXAA00091
• Pickle Fork
• Torque Angle Gauge
• Trim Tool Set 1aau.to/oq6/1AXXX00006
• 3/8 Inch Air Impact Gun
• Ratchet 1aau.to/oWw/1AXAA00016
• Torque Wrench 1aau.to/oBn/1AXAA00044
• Center Punch 1aau.to/oc7/1AXAA00055
• Hammer 1aau.to/oou/1AXAA00091
• Sledge Hammer 1aau.to/oou/1AXAA00091
Subscribe: / @trq
Check out our playlist:
Chevy Cruze 2011-2015 1st Gen: • Chevy Cruze 2011-2015 ...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video. - Авто та транспорт
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts
√ *Do it Yourself*
√ *Save Money*
Very helpful !! I used this to complete the job on a 2016 Chevy impala. Also replaced inner & outer tie rod ends. Same setup as this video. Thanks !!
yes you should replace those bolts holding the control arm in, my bolt broke off while i was unscrewing it.
Awesome, thank you. Clean, precise, exactly what I was looking for.
Thank you. Best video for this job on youtube.
Thank you very much after seeing this I know I van do this now. I have a 2014 Holden Captiva so will it be similar?
Very helpful, preciate it 👌
Thank you
An extra 75 degrees when tightening sounds like "torque to yield" bolts. are they? and if so, don't they need to be replaced?
now hard is a "bonk" lol
I replaced this part and my car is still making the same noise but worse… not sure what my issue is now
What is 'ride height' can you elaborate a bit on that?
How can you notice if it's time to change them?
Can u do mine
how much is that?
Fantastic
+Turbo Jones Thanks for watching our video! 1aau.to/m/Shop-TRQ
put the tools used in the description!
If you can't figure out the tools, you aren't equipped or qualified to do this simple job.