Let me give you some words of advise. Get some sheet lead and line those jaws with the lead. Clamping down on those gears with steel jaws will ruin some gears. The lead will cushion the gear while holding it stable.
I used ua-cam.com/users/postUgkx4ynqaujg7rZKFapA8s29kTpRszJGa3-K this for the first time today to replace the front wheel bearing on my rwd 98 dodge dakota. This had absolutely no issue removing or reinstalling the lug nuts and it took off the axle nut without any struggle. Sounds like it's got some muscle to it. Time will tell
Open the chuck jaws. Remove the screw located in the centre. Fit a 3/8" (10mm) Allen key into the chuck and tighten with the chuck key. Smack the end of the Allen key with a hammer in an anti-clockwise direction and it will unscrew from the machine. Refitting is a reversal of this procedure. You do not have the split the drill body.
that method doesnt work with this particular model makita 6404 the shaft still spins in both directions when you put the allen key in it and there is no flat on the shaft for a spanner to hold it to smack it with a hammer. That model is about 40 years old.
Great Video! This is the only way to change the chuck if your drill spins too loosely to untighten the chuck the other way. The other way is tightening the chuck on a hex wrench and hitting it with a snap. My chuck was actually stuck in the open position so I couldn't tighten it on a hex wrench....this video saved my drill! Thanks.
Thanks for the video. If the video had been available many years ago I would have replaced the chuck on my old B&D. Replacement parts were more readily available and cheaper. These days the replacement chuck costs as much as a new drill so I would just toss the worn-out B&D and buy a new one.
Desde colombia. Gracias por el video. Solo es que el tornillo que sujeta al mandril es rosca izqierda para que tomen nota y miren como gira el destornillador. Gracias vale.
You don't clamp gear on a vice Steel to steel .you can use Taflon or copper in between To avoid damage the gear. To replace chunk today is not Profitable as too many cheap Chinese drilling machine on the market
Never clamp a cog wheel in a vice. If it is necessary, then use a soft wood in the vice jaws to protect the teeth. The drill does not need to be disassembled to replace the chuck. See other videos.
The 'smack with a hammer' technique probably applies to older drills. I have a drill dating from about 2015 and wanted to remove the chuck. Unbeknown to me, there is a screw, left-hand threaded accessible with an Allen key placed into the fully open chuck. Old man with 'weak' hands that I am, trying to undo this screw as though it were normal RH, snapped said screw in two. Drill and driller are both fine but replacement LH screws are not that cheap or readily obtainable!
you have seen the hard way now i will tell you the easy way place drill in vise open chuck insert screw driver turn clockwise to remove the screw insert the key in chuck give it a good (WACK) counter clockwise now unscrew old chuck add new chuck install scew counter clockwise you are thru a 5 min job..
First and foremost, you don't really need to pull out the gears in order to change the chuck. Looking at the damage on the collet gears, it seems that you are a rough user. This is further demonstrated by the way you clamped the gears directly to the vise. I am not surprised that you will soon be changing another chuck in a very near future.
My B/D drill with attachments to fix I just have to put bit tighten key & give it slight blow from a hammer to remove the chuck to fit attachments, eg. saw, orbital sander etc. No need to remove any screws or open the body cover.
It looks like you cheeched the teeth on that gear by clamping it unprotected in your vice. I could see the damage when you removed it. You need to put some wood, leather, or something else between the vise jaws and your workpiece to prevent marring.
No need to takeout output spindle and gear assembly to remove the chuck. Allen key and a strike with a hammer would have done the work 🙁. I replaced the chuck of my skil 13mm drill by the above method.
Thanks for your time, but I don't disassemble the drill to disassemble the chuck, I have a used key that enters and blocks the axis and then I unscrew the chuck
No need to remove the casing.put the key to the chuck and reverse use the hammer and you can remove the chuck.very simple only seconds to remove the chuck.
Um das zu machen, -also das Dreibackenfutter zu wechseln- benötige ich maximal 2 Minuten! Hätte er nicht so oft beim festziehen oder lösen in die verkehrte Richtung gedreht, so hätte er schon viel Zeit gewonnen. Er wird nie ein Handwerk ausüben -soll man lieber studieren- da kann er sich anders blamieren! Der Schreiber ist gute 85 Jahre alt und wwünscht noch viel Erfolg!
remove the phillips head screw in side the chuck you need to turn it clockwise to remove it if you place the drill in a vice put a wrench on the chuck give the wrench a good lick counter clockwise t0 remove it once you break it loose it will unscrew by hand
make sure the chuck is open like you are inserting a drill bit look in the back inside the chuck there is a screw that holds the chuck to keepit from unscrewing take it out clockwise
Let me give you some words of advise.
Get some sheet lead and line those jaws with the lead. Clamping down on those gears with steel jaws will ruin some gears. The lead will cushion the gear while holding it stable.
Wood is also an option. Wooden plank.
I used ua-cam.com/users/postUgkx4ynqaujg7rZKFapA8s29kTpRszJGa3-K this for the first time today to replace the front wheel bearing on my rwd 98 dodge dakota. This had absolutely no issue removing or reinstalling the lug nuts and it took off the axle nut without any struggle. Sounds like it's got some muscle to it. Time will tell
Nice dahil sayo madamikang natutulongan mga carpenter
Open the chuck jaws. Remove the screw located in the centre. Fit a 3/8" (10mm) Allen key into the chuck and tighten with the chuck key. Smack the end of the Allen key with a hammer in an anti-clockwise direction and it will unscrew from the machine. Refitting is a reversal of this procedure. You do not have the split the drill body.
that method doesnt work with this particular model makita 6404 the shaft still spins in both directions when you put the allen key in it and there is no flat on the shaft for a spanner to hold it to smack it with a hammer. That model is about 40 years old.
@@kenpoman1 You do not need to lock the spindle. The inertia will free the chuck eventually.
The END !! of the Allen ! Key ! ?? You Either ! Bend ! Or ; Break ! Or DAMAGE ! the Drill !.Doing that !!
@@davidwillard7334 - Ah, No.You've apparently changed a drill chuck or used a hex key.
21 21 56
Sir thank u sa video mo natuto ako pano mg replace Ng drill chuck more bless sa channel mo sir..now I know...yes!!
Great Video!
This is the only way to change the chuck if your drill spins too loosely to untighten the chuck the other way. The other way is tightening the chuck on a hex wrench and hitting it with a snap. My chuck was actually stuck in the open position so I couldn't tighten it on a hex wrench....this video saved my drill!
Thanks.
What if it frozen to tighten position? I cannot loose it..
@@clarkstarks6767 ....have you tried PB Blaster and a pipe wrench to loosen it? that should loosen it to allow access to the center screw.
Sounds like ! YOU ! STUFFED !.! IT ! UP !! EVEN !! MORE !! NOW !!
nice bro maraming matulongan
Thanks for the video. If the video had been available many years ago I would have replaced the chuck on my old B&D. Replacement parts were more readily available and cheaper. These days the replacement chuck costs as much as a new drill so I would just toss the worn-out B&D and buy a new one.
And Still ! Have ! PROBLEMS ? With that ! Too !!
Very helpful boss galing napalitan ko na chuck ko nabasag kasi ang bit kala ko may naiwan pang turnilyo big help talaga
Thank you very much, now I can easily replace mine🇿🇦
Canal show de bóla dicas top mesmo parabéns amigo 💯👍👍🇧🇷
Desde colombia. Gracias por el video. Solo es que el tornillo que sujeta al mandril es rosca izqierda para que tomen nota y miren como gira el destornillador. Gracias vale.
Thank you po Sayo sir.maaayos Kona itong sira na electric drill na SI na Ang drill shop.
Thank you, that helps me.
Thanks for video now I can replace my drill chuck
And Damage !. The! Gear ! Too !
lol.that was easy.glad the gear didnt break when you lock on the vice.😅
Thanks it is good video but it can be replaced without opening the cover..
How to fix a rod will turn with key
Very good information, thank you bro
Good idea dear
Good nagkaroon ako ng idea thanks
never seen it done like this before. There is a much easier way
Very nice 👍👍
You don't clamp gear on a vice
Steel to steel .you can use
Taflon or copper in between
To avoid damage the gear.
To replace chunk today is not
Profitable as too many cheap
Chinese drilling machine on the market
Thank you so much for sharing this video idol keep safe and stay healthy idol Godbless you always 🙏😍❣️
Maraming salamat sa kaalaman bro stay safe god bless.
kafi bidwan ho bhaisab aap..gear ko vice me tight kardiye bina packing k... naman aapko
Great job and good video if u move the music🙏👍🤣🇩🇰
ကျေးဇူးတင်ပါတယ်ဆရာ.....နည်းလမ်းလေးဝေမျှပေးတာ
Amigo creo que debiste colocar algo,entre las quijadas o mordazas de la prensa, algo así como unas tiras de madera, para no dañar el engrane.
Muy buena su observación yo también me di cuenta.👍
Very good idea thanks
Never clamp a cog wheel in a vice. If it is necessary, then use a soft wood in the vice jaws to protect the teeth. The drill does not need to be disassembled to replace the chuck. See other videos.
The 'smack with a hammer' technique probably applies to older drills. I have a drill dating from about 2015 and wanted to remove the chuck. Unbeknown to me, there is a screw, left-hand threaded accessible with an Allen key placed into the fully open chuck. Old man with 'weak' hands that I am, trying to undo this screw as though it were normal RH, snapped said screw in two. Drill and driller are both fine but replacement LH screws are not that cheap or readily obtainable!
unbelievable, unscrew the whole Drill to change the chuck; he did not need my friend
You replace the chuck but you damage the gear.
😂
Tama😂
Senseless way
Thanks for showing the long way to do this
Exelente video
you have seen the hard way now i will tell you the easy way place drill in vise open chuck insert screw driver turn clockwise to remove the screw insert the key in chuck give it a good (WACK) counter clockwise now unscrew old chuck add new chuck install scew counter clockwise you are thru a 5 min job..
My drill dosent have a screw in the middle what do I do
Another STOPWATCH !! IDIOT !! HERE !!
NO SCREW INSIDE THESE CHUCKS
First and foremost, you don't really need to pull out the gears in order to change the chuck.
Looking at the damage on the collet gears, it seems that you are a rough user. This is further demonstrated by the way you clamped the gears directly to the vise. I am not surprised that you will soon be changing another chuck in a very near future.
True 😂😂
I think putvthe gear below so that it does not demage
Hvala na savjetu
Good 👍
maraming salamat boss godbless
good video
Vejam meu vídeo como tirar o mandril sem desmontar a máquina
Very good thanks you
THANK YOU FOR YOUR CLEAR VIDEO
I would bet Noah was the previous owner of the vice.
nice
My B/D drill with attachments to fix I just have to put bit tighten key & give it slight blow from a hammer to remove the chuck to fit attachments, eg. saw, orbital sander etc. No need to remove any screws or open the body cover.
Very nice video thank you sir very much.
Thank you for your post. I like this vd.
It looks like you cheeched the teeth on that gear by clamping it unprotected in your vice. I could see the damage when you removed it. You need to put some wood, leather, or something else between the vise jaws and your workpiece to prevent marring.
i believe you can do it without overhauling the device
ILike 😻😻
💞💞💞
great.
thanks bro
Wrong method... Between the steel wise plates, Gear will get damaged
He should have clamped it between two pieces of hardwood.
No need to takeout output spindle and gear assembly to remove the chuck. Allen key and a strike with a hammer would have done the work 🙁. I replaced the chuck of my skil 13mm drill by the above method.
Yes, you'r right to say.
Thanks for your time, but I don't disassemble the drill to disassemble the chuck, I have a used key that enters and blocks the axis and then I unscrew the chuck
For a 9 mins video he has taken 4 mins to adjust camera.
Awesome instruction video 😎
👌👌👌
👍👍👍
👍👍
i am learning thanks.
Yyyyyty
Sounds ! More ! Like !! STEALING !! THAN ! ! ANYTHING !! ELSE !!
굿
Thanks you sir
Brilhante a essa eu vou aprender 😃👍
puoding maka ordir ng barina yan malaking bilog na gir
Solo tienes que meter algo en el aspa para que no ae mueva y girar el trompo del lado contrarip de comongira y ae suelta y metes el.otro listo
Big mistake! Don’t use a vice on that gear! Now you will need to replace it!
you 're' right, it is a big mistake.
You use vise to hold the thread?. It can damage the teeth
Kesuen langsung copot baute didrip kendoni
👍
Salamat po info sir
That is completely correct. When I change a tyre, I also drain the coolant first.
And Lost ! The Air ! Too !!
DE VALT ,10mm ഡ്രിൽ മെഷീൻ റെ ബോൾ ബെറിങ് കിട്ടുമോ നമ്പർ അറിയില്ല
No need to remove the casing.put the key to the chuck and reverse use the hammer and you can remove the chuck.very simple only seconds to remove the chuck.
Not Such a Good ! IDEA ! With Pins ! In it !!
It can be done unscrewing the machine.
Mas maganda cguro kong samahan mo ng instruction o magsalita ka para mas lalong maintindihan ng nanood
use 12 mm wrench and vice grip
TQ
Thanks I didn't know that
Bos sy butuh buat merk bor maktek ...
Merci pour l’astuce . J’ai un problème pour changer le mandrin je ne sais pas comment m’y prendre.
Um das zu machen, -also das Dreibackenfutter zu wechseln- benötige ich maximal 2 Minuten! Hätte er nicht so oft beim festziehen oder lösen in die verkehrte Richtung gedreht, so hätte er schon viel Zeit gewonnen. Er wird nie ein Handwerk ausüben -soll man lieber studieren- da kann er sich anders blamieren!
Der Schreiber ist gute 85 Jahre alt und wwünscht noch viel Erfolg!
Usta o MANDRENI böylemi değiştiriyor aslında çok basittir
remove the phillips head screw in side the chuck you need to turn it clockwise to remove it if you place the drill in a vice put a wrench on the chuck give the wrench a good lick counter clockwise t0 remove it once you break it loose it will unscrew by hand
NO SCREW INSIDE THESE CHUCKS
Thanks
R u not damaging the teeth of the cog, by clamping it directly on a vic?
yes not damage teeth of gear
That's what I thaught too. Personally I would have used a woodworkers vice or one that has wooden grips on it.
Looks like the vice (correct spelling!) is next in line for a makeover!
Like THE ! METAL ! SHREADDER !! AWAITS ! IT !!
Methuselah called... he wants his bench vice back.
Yes that's a genuine relic~!!
Thanks🌹
Con una prueba al taladro se ganan el trabajo .
Thank you
the chuck may its good but the gear may cause damage at vise may cause crack
next time DONT TAKE THE DRILL APART just remove the screw and undo the chuck a lot easer
Even if there are pins in it too !.
NO SCREW INSIDE THESE CHUCKS
He has to put some aluminum plate in the vise to protect gear tooth get damaged 😀😀😀😀
dapat may tela o basahan yung gear para hindi masira pre..
sapag kaka ipit mo sa gato maaaring madamage yung gear nya.
You do not take the chuck off by striping the dril 🤦🏼♂️
I don’t have a screw in the middle of my chick so what do I do
Why do you STRIPE ! YOUR DRILL CHUCK ! THEN !??
Sir. TEK. MORE POWER UR. GOOD. CHANNEL,. THIS. VIDEO. MERON. SANA. AKONG TANONG. SA MUSIC. BACKGROUND MO WALA BA. SYANG COPY RIGHT.. SALAMAT SAGOT..
make sure the chuck is open like you are inserting a drill bit look in the back inside the chuck there is a screw that holds the chuck to keepit from unscrewing take it out clockwise
taga saan kpo pwede po pagawa
@@mylinevaristo9073 dont speak your lang. sorry
@@frankdavidson9675 NO SCREW INSIDE THESE CHUCKS