IT WORKED.....26.5 minutes....drove it for 5 minutes....light disappeared....drove it back home...light not back.....I I will update later if the light does not return.... AWESOME.....thank you so MUCH> the cable from Ross-Tech was $200 = tax...I got regular free shipping. All the other videos....did not work...but yours did....so far....I hope it sticks... Thank you so much. I did not have enough battery in my computer to run again the codes....but I will try again in a few days if I need to, Pittsburgh Dad Texas
If the DPF is already clogged, maybe it is time to remove it and get cleaned profesionally or atleast home cleaned using pressure washer and dpf chemicals.
@@dionich Do you have a favorite dpf cleaner / spray? From what I understand: 1. remove the O2 sensor near rear top of 2.0 TDI, 2. with the engine stopped and warm, spray in short bursts until the can is empty, 3. Let cleaner/foam sit for 20-25 minutes, 4. initiate regen OR drive car at consistent freeway speed for 40 minutes? Anything else I should know? Thanks so much!
Mine MQB platform, says aborted due to safety. stop engine & try again, but same message again. Want to try driving regen. Do you know what value to set ?? After I go into driving while regen settings on vcds it states stored value 0 should I put new value 1 ?
Hi. I didn't try to regenerate during driving, cannot recommend anything. It requires different password 12233 as far as I understood. I didn't get it why those "safety errors" popup.
I had this keep happening to me too. I don't know if it was because I didn't tap the gas pedal or slowly relased the pedal but once I did it the tap version very quickly it finally said running....
@@TheeHomelessRunner it’s 1:29 am, currently searching the Internet, more problems on Passat b7, totally dead battery & locked out, emergency plastic key doesn’t unlock the drivers door. It turns right & left but doesn’t open the door… arghhh. Does anyone have any tricks to open the bonnet. Seen tricks on b6 thr the grill but 2011 b7 nothing…. 😳😳😳😳😳
Even smashing window don’t think it will allow me to pull handle to open the bonnet. Will get me the locking wheel nut tho, wheel off wheel liner off to eventually get to the cable… got to be an easier way ?????
I have a 2014 Passat TDI with check engine light code P2459 & vehicle tends to overheat while driving on highway & when I downshift & floor it to over 3k rpms it would instantly cool its self down
@@dionichI have replaced the EGR sensor and pressure sensor. I just ordered VCDS and will try to do a regeneration as you did and hopefully that works
Seems more like a coolant circulation problem of overheating while steady driving. You should probably try doing a coolant flush (empty the cooling system for fluid, put in cleaning additive let it run for a bit, flush a couple of times with clean water) and also you should check if your thermostat opens fully. You can check by pulling it of, put it in a pot with water and boil it. It should start moving/opening around 85-90°c. Also clean your radiator and condensator for AC for leaves and other road debries.
Hi. I did also receive "Aborted, safety reason" error messages, but do not udnerstand the root of this. Sometimes they appear, sometimes they do not and the procedure runs without any issues.
IT WORKED.....26.5 minutes....drove it for 5 minutes....light disappeared....drove it back home...light not back.....I I will update later if the light does not return.... AWESOME.....thank you so MUCH> the cable from Ross-Tech was $200 = tax...I got regular free shipping. All the other videos....did not work...but yours did....so far....I hope it sticks... Thank you so much. I did not have enough battery in my computer to run again the codes....but I will try again in a few days if I need to,
Pittsburgh Dad Texas
If the DPF is already clogged, maybe it is time to remove it and get cleaned profesionally or atleast home cleaned using pressure washer and dpf chemicals.
@@dionich Do you have a favorite dpf cleaner / spray? From what I understand: 1. remove the O2 sensor near rear top of 2.0 TDI, 2. with the engine stopped and warm, spray in short bursts until the can is empty, 3. Let cleaner/foam sit for 20-25 minutes, 4. initiate regen OR drive car at consistent freeway speed for 40 minutes? Anything else I should know? Thanks so much!
Nice manual, thanks!
Mine MQB platform, says aborted due to safety. stop engine & try again, but same message again. Want to try driving regen. Do you know what value to set ?? After I go into driving while regen settings on vcds it states stored value 0 should I put new value 1 ?
Hi. I didn't try to regenerate during driving, cannot recommend anything. It requires different password 12233 as far as I understood. I didn't get it why those "safety errors" popup.
@@dionich regen while driving.. yes change value from 0 to 1. Click do it & then it enter’s rengen. Drive 20 mins light goes off. Sorted
I had this keep happening to me too. I don't know if it was because I didn't tap the gas pedal or slowly relased the pedal but once I did it the tap version very quickly it finally said running....
@@TheeHomelessRunner it’s 1:29 am, currently searching the Internet, more problems on Passat b7, totally dead battery & locked out, emergency plastic key doesn’t unlock the drivers door. It turns right & left but doesn’t open the door… arghhh. Does anyone have any tricks to open the bonnet. Seen tricks on b6 thr the grill but 2011 b7 nothing…. 😳😳😳😳😳
Even smashing window don’t think it will allow me to pull handle to open the bonnet. Will get me the locking wheel nut tho, wheel off wheel liner off to eventually get to the cable… got to be an easier way ?????
I have a 2014 Passat TDI with check engine light code P2459 & vehicle tends to overheat while driving on highway & when I downshift & floor it to over 3k rpms it would instantly cool its self down
Hi. Try to google this code plenty topics out there starting from pressure sensors, clogged egr etc
@@dionichI have replaced the EGR sensor and pressure sensor. I just ordered VCDS and will try to do a regeneration as you did and hopefully that works
Seems more like a coolant circulation problem of overheating while steady driving.
You should probably try doing a coolant flush (empty the cooling system for fluid, put in cleaning additive let it run for a bit, flush a couple of times with clean water) and also you should check if your thermostat opens fully. You can check by pulling it of, put it in a pot with water and boil it. It should start moving/opening around 85-90°c.
Also clean your radiator and condensator for AC for leaves and other road debries.
do tutorial videos about vcds please , thanks already
Noted!
Hi. I have error 17262 Passat 2012 CFFB. do you have any idea what is causing it?
Hey. Sorry, never encountered. Try to google it.
Can you run A regeneration if you only have a desktop computer?
Yes
Awesome. I just ordered my VCDS this morning. I have a p2459 code. Hopefully I can figure it out
@@amichael8367Good luck. I have two sets of diag software installed, on the laptop and on the desktop in my garage
Would you be open to me asking questions once I get my VDCS?
Yeah
Do i have to heat up the engine first or can i start the dpf regeneration cold
I would say, better to heat up since regeneration is a process of burning extra amount of fuel.
@@dionich so go for a 20 minute driver or something like that
@@osmaniljazovic6201 Yeah. Make the engine operating temperature
@@dionich okay thank you very much for your feedback friend
@@dionich when should i do the dpf regeneration once every 30 kilometers or more?
Could you tell me what VCDS you use, please ?
Just a random cheap chinese cable bought locally with cracked software :)
@@dionich thank u man !
What connection is the laptop to the car?
HEX-V2
what do i do if it begins the process and then kills the car and says abort. i have tried multiple times but nothing works
Hi. I did also receive "Aborted, safety reason" error messages, but do not udnerstand the root of this. Sometimes they appear, sometimes they do not and the procedure runs without any issues.
M’y code security dont work 27971 i have dont accès ..
Cannot help you out here mate, try to google it.
What cable do I need to run this operation? Can I use a 3rd party cable?
Hex-v2. Don't know.
It is not giving me to proceed the regeneration way ?
This function is strange indeed, doesnt start properly sometimes. Need to try several times. Dont know how to improve that.
@@dionich ok thanks i will try several times