Can you tell me how to wire these fans, and what kinda plug I need? I can send a picture of the plug but can’t figure out how to attach it. Fan look exactly like the one leaning on the truck. The plug looks like it would have four prongs but it only has three, two next to each other than a space then the other. Sposed to fit 2014 and up Silverado.
How deep is that single large fan from the 2015 SS? Can you give me a measurement from the shroud mounting surface that would go against the radiator core to the back of the motor and also yje diameter of the motor? Also very curious about how I could control that big Spal fan in a non-ECU engine with a plain old Holley double-pumper. The link you have doesn't seem to work any more.TIA-Mike
Does anyone know if the Camaro fan can be run on normal DC? I've been told it may be possible by grounding the PWM wire. I'm not going to buy a fan to find out. If it can then I've been told by autocoolguy that their PWM controller will control it.
AWG 8 is not ok for the 19" fan Why? Because: I(A) = P(W) / V(V) 835w/14v=60A That is AWG 6 wire Ampacity spot on, AWG 8 wire Ampacity is 55A Including engine bay Thermal Derating factor
Great info! I have an L83/JKUR with the factory Jeep fan. Works well except when towing. Wondering if that Camaro fan would be a good option. Could it integrate with my Motech swap?
I removed my dual fans just like those and added two 13" spal. How do I wire them in or what do I need? Will the controller you show work for my fans to work at different speed? I had my truck tuned by you sometime back. Just that I decided to get better spacing between engine and stock fans.
Have you compared that Camaro fan vs the factory JK fans for air flow? Also, I'm sure you're aware, but just in case you aren't the JT fans are even bigger & move more air that the JL's fans.
Good evening, what is the name of this fan, and was it installed on a car from the original, and what is the name of the car on which it was installed? With many thanks 🌷🌷🌷🌷🌷🌷🌷
bought the same pwm generator n tested GMC Acadia fan (same as SS n Cadillac XT5 n Tesla X). worked on 100hz (it handles some freq range didn't test it). Turns on ~90% DC (low speed), didn't test the off DC. Looking at this video, he's pressing down arrow to speed up (lower DC). Tesla X fan is opposite (normal i call it), turns on at 15% n goes up from there, probably turns off at 90%, didn't test it.
O. Ok I would have to buy the fan. And were can I find that controller. I would like to put one on my 1996 Silverado has original vortec engine so I think I would need that controller right ?
I know this post is old but I'm currently looking for a cooling solution for my 2002 LM7 into my 1997 obs Silverado. Can you give me a total cost for one of your dual Brushless setup, I have the 34x19in radiator. Thanks! If you only have a recommendation that would help too.
Can you tell me how to wire these fans, and what kinda plug I need? I can send a picture of the plug but can’t figure out how to attach it. Fan look exactly like the one leaning on the truck. The plug looks like it would have four prongs but it only has three, two next to each other than a space then the other. Sposed to fit 2014 and up Silverado.
How deep is that single large fan from the 2015 SS? Can you give me a measurement from the shroud mounting surface that would go against the radiator core to the back of the motor and also yje diameter of the motor? Also very curious about how I could control that big Spal fan in a non-ECU engine with a plain old Holley double-pumper. The link you have doesn't seem to work any more.TIA-Mike
What vehicle did you get the dual fan setup out of, what size are they and how much they cost???
Does anyone know if the Camaro fan can be run on normal DC? I've been told it may be possible by grounding the PWM wire. I'm not going to buy a fan to find out. If it can then I've been told by autocoolguy that their PWM controller will control it.
AWG 8 is not ok for the 19" fan Why? Because:
I(A) = P(W) / V(V)
835w/14v=60A
That is AWG 6 wire Ampacity spot on,
AWG 8 wire Ampacity is 55A
Including engine bay Thermal Derating factor
I use dual spal 16’ fans with a ebay shroud, will your harness with them?
Thanks for all your videos mitch you the best for teaching us out here i called you but no answer u r on vacation no dought
Great info! I have an L83/JKUR with the factory Jeep fan. Works well except when towing. Wondering if that Camaro fan would be a good option. Could it integrate with my Motech swap?
Where can we order a harness for the SS camaro fan? Would it be possible to see which wires you have going to pos and neg. My plug is cut off.
Email me at swaptimeusa@gmail.com
I removed my dual fans just like those and added two 13" spal. How do I wire them in or what do I need? Will the controller you show work for my fans to work at different speed? I had my truck tuned by you sometime back. Just that I decided to get better spacing between engine and stock fans.
on the E92 controller which Pin on the X1 (blue connector)? 59 or 42?
I'm working on a 56 buick I was wondering the size of the ss fan to get an idea if it'll fit my radiator I'll appreciate the info.
Very nice setup on both..
Where can I find a PWM fan(s) for my 69 C10 Radiator? New or used - If used out of what car or truck?
hey Mitch can be installed in a genIV?... also do you know deep is the camaro ss fan? is for a land rover conversion.
Any factory brushless fans in the 18" tall x 22" wide range????
Have you compared that Camaro fan vs the factory JK fans for air flow? Also, I'm sure you're aware, but just in case you aren't the JT fans are even bigger & move more air that the JL's fans.
Good evening, what is the name of this fan, and was it installed on a car from the original, and what is the name of the car on which it was installed? With many thanks
🌷🌷🌷🌷🌷🌷🌷
What fan would you use in a 94-96 impala
Same question, but with a 468 BBC
I have a question witch fan would u recommend for 84 k5 blazer? I want to put a 5.3 l83
Hey Mitch i need a harness for a ls engine from 2003 tahoe. How can some one get in touch for a engine harness and a e fan harness. Like your work
Can we use the PWM fans on older 2005 Chev trucks ?
@Swap Time Is that 2016 Spal Camaro SS fan an 850w motor?
Can you show us how you contacted the controller in the fans like you did, please, as I burned my fans by mistake😂
How thick is Camaro fan?
Can you make the ss efan fit a 2011 Colorado v8 factory
Amp draw at max rpm on each?
What were the controller settings for running the fan?
bought the same pwm generator n tested GMC Acadia fan (same as SS n Cadillac XT5 n Tesla X). worked on 100hz (it handles some freq range didn't test it). Turns on ~90% DC (low speed), didn't test the off DC. Looking at this video, he's pressing down arrow to speed up (lower DC). Tesla X fan is opposite (normal i call it), turns on at 15% n goes up from there, probably turns off at 90%, didn't test it.
Hey Mitch would you recommend the truck fan or the camaro ss fan for a 87 g body Monte Carlo? Putting in a lt1 with the gm performance swap harness
Measure your radiator and see which fan type will fit. Both are impressive
31x19 is the radiator dimensions. So I’m thinking the truck fan. Will I need your harness to hook it up to the gm swap harness?
Travis Swisher yes
very good info
can you find Haw many amps each fan draw?
thanks
The 2016 camaro v8 uses a 100 amp fuse for the power wire on that fan.
great video!!!
Thanks for the knowledge
Can it control the JK 12&up PWM Fan
Yes
Thanks
I find the Pwm controller in EBay and also there is another one with a thermometer
nice wondering holley terminator X signal support these fans?
They will, but you will not have PWM..Just on and off....
I think you can set up and advanced table and have PWM
Terminator x only does pwm
How much for the dual harness
70$ for the truck dual fan harness
Swap Time ok can u send me ur address or do u have cash app or how we do this thanks in advance
Can you please let me know prices
70$ for the truck dual fan harness, 80$ for the camaro ss fan harness.
O. Ok I would have to buy the fan.
And were can I find that controller. I would like to put one on my 1996 Silverado has original vortec engine so I think I would need that controller right ?
I know this post is old but I'm currently looking for a cooling solution for my 2002 LM7 into my 1997 obs Silverado. Can you give me a total cost for one of your dual Brushless setup, I have the 34x19in radiator. Thanks! If you only have a recommendation that would help too.
Question, where are you located?
Las Vegas
Swap Time If i bring my velle out would you be open on doing the tahoe cluster swap?
@@pilsonandrew As long as it has a gen iv or gen v engine
Swap Time not a gen 3?
@@pilsonandrew Gen 3s do not have can bus and it will not work this time
Pretty loud