Glue should always be applied with a toothpick. I use two glues - Zap a Gap and a 5-second bonding super glue. We use magnets and 35,000 -52,000 rpm motors here in Memphis TN. USA. We run Slot.it, NSR, FLY and some Ninco. Carrera, Scaletrex and Pioneer are considered "hunks of junk", but we modify them the best we can. The JB Weld is a bad idea if you need to swap out your motor. Don;t use concrete, use a motor mount screw. If your hunk of junk doesn't have motor mount screw holes, make them. You put magnets (optional), then the motor with pinion in the chassis first, then the bushings and rear axle because the chassis has to flex when you insert the motor. Lastly, don't glue tires on, get appropriate silicone tires that fit your wheels.
Hello, First...thank you for the videos. There are very useful. Some questions: Could you make a similar setup but with a Pioneer Camaro? Is it posible to chage the guide (nsr, Avant, Ninco...) to Pioneer cars? What is the manufacturer of the glue you use in this setup? What is the ref. of the nsr tyres treatment oil you use in the video "NSR Tyre Treatment oil"? Thank very much
It’s a pity such relatively inexpensive modifications aren’t available directly from the manufacturer as standard, I’m sure most slot racers would agree that to buy a competitive car without recourse to chopping and changing the basics to get it to a decent track worthy state would be the preferred choice.
ive had the same car the torqeu of the engine will eventualy break off the little clips holding the engne to the car also had 2 camaro's they broke right below the rearaxle.
Yes, there's one modification he should have made, replace the chassis completely, Scalextric chassis are CRAP... they break very quickly and are difficult to get to handle, as you can see, he has to modify the chassis, stupid thing to have to do... Scalextric build HORRIBLE cars... the bodies are ok sometimes
I appreciate the explanation but need to lean more what where to look for some of the tools of the trade such as: what is used on the new tires, where can you look for the truing tool used on the rear tires? Thanks in advance.
Glad the slot cars have come back. I used to love them in the 60's. The smell of o-zone and rubber. Cars with metal chassis and plastic body of various mid 60's models.
Great video mate, I have watched a few of yours now, they are always well made and very informative. I especially like the car upgrades you cover of the consumer level to what some may call prosumer level slot car builds. It is a great sport that can be enjoyed at so many levels - thanks for sharing!
when cutting the plastic bodies i use a rubberized mat for better grip in holding the body in place. i understand that you may have to use the white table here for better visibility in the video but sacrifice some stability & precision. liked & sub'd
Recently stumbled across your channel after deciding to drag our Quantum of Solace digital set out during lockdown. Although your mods are way beyond our needs, its fascinating to see what can be achieved. After seeing your Aston Martin GT3 mods, I bought the AM GT3 C4036! Best wishes from the UK. Steve
I don't know where about's you are in NZ but my buddy Mark Millings lives in West Port & he is the European Slot Car Champion & runs a club called West Port Slot Car Club Like you he's an absolute magician when it comes to building race winning slot cars Thanks for producing a cracking video
Because it's called modelling; enjoying the challenge of modification and adaptation. Something creative as opposed to unimaginative cheque book "modelling" that you propose. Thumbs up to the original poster of this video.
Glue should always be applied with a toothpick. I use two glues - Zap a Gap and a 5-second bonding super glue. We use magnets and 35,000 -52,000 rpm motors here in Memphis TN. USA. We run Slot.it, NSR, FLY and some Ninco. Carrera, Scaletrex and Pioneer are considered "hunks of junk", but we modify them the best we can. The JB Weld is a bad idea if you need to swap out your motor. Don;t use concrete, use a motor mount screw. If your hunk of junk doesn't have motor mount screw holes, make them. You put magnets (optional), then the motor with pinion in the chassis first, then the bushings and rear axle because the chassis has to flex when you insert the motor. Lastly, don't glue tires on, get appropriate silicone tires that fit your wheels.
That’s a gorgeous track. I just recently got into Scalextric. I wish your shop was here in Canada. 👊🏻
Michael Doyle I think he went out of business for some reason.
Nice tuning bro.
Hello,
First...thank you for the videos. There are very useful.
Some questions:
Could you make a similar setup but with a Pioneer Camaro?
Is it posible to chage the guide (nsr, Avant, Ninco...) to Pioneer cars?
What is the manufacturer of the glue you use in this setup?
What is the ref. of the nsr tyres treatment oil you use in the video "NSR Tyre Treatment oil"?
Thank very much
It’s a pity such relatively inexpensive modifications aren’t available directly from the manufacturer as standard, I’m sure most slot racers would agree that to buy a competitive car without recourse to chopping and changing the basics to get it to a decent track worthy state would be the preferred choice.
Wonder what he's done to the Challenger
ive had the same car the torqeu of the engine will eventualy break off the little clips holding the engne to the car also had 2 camaro's they broke right below the rearaxle.
Yes, there's one modification he should have made, replace the chassis completely, Scalextric chassis are CRAP... they break very quickly and are difficult to get to handle, as you can see, he has to modify the chassis, stupid thing to have to do... Scalextric build HORRIBLE cars... the bodies are ok sometimes
You should have replaced the WHOLE chassis.
Yeh, that's what I was thinkin as well...
I appreciate the explanation but need to lean more what where to look for some of the tools of the trade such as: what is used on the new tires, where can you look for the truing tool used on the rear tires? Thanks in advance.
Glad the slot cars have come back. I used to love them in the 60's. The smell of o-zone and rubber. Cars with metal chassis and plastic body of various mid 60's models.
Slot bodgery LOL! JB. you would make a good BSA owner.
Great video mate, I have watched a few of yours now, they are always well made and very informative. I especially like the car upgrades you cover of the consumer level to what some may call prosumer level slot car builds. It is a great sport that can be enjoyed at so many levels - thanks for sharing!
Why aren't the manufacturers doing this?
What kind of glue did you use for the tires ?
And are those tires silacone?
when cutting the plastic bodies i use a rubberized mat for better grip in holding the body in place. i understand that you may have to use the white table here for better visibility in the video but sacrifice some stability & precision. liked & sub'd
Recently stumbled across your channel after deciding to drag our Quantum of Solace digital set out during lockdown. Although your mods are way beyond our needs, its fascinating to see what can be achieved. After seeing your Aston Martin GT3 mods, I bought the AM GT3 C4036! Best wishes from the UK.
Steve
Finally some old school muscle bodies not ricers or pasta rocket's
I learned so much!! Greatly informative. Tx mate.
I don't know where about's you are in NZ but my buddy Mark Millings lives in West Port & he is the European Slot Car Champion & runs a club called West Port Slot Car Club Like you he's an absolute magician when it comes to building race winning slot cars Thanks for producing a cracking video
wanna send me a slot car lol
there way too expensive now
Kinda curious about how easy it would be to remake a scaletrixs car into a small RC just out of curiosity.
Wouldn't the body roll make the back end slid out !
would love to come and see your shop and setup next time im in your erea, Nice vids well done. William
This was one of the better videos, good job
So I will have a different track to run on.
Should have cleaned your nails
Where do you get the models?
great helpful vid, thax I'm subscribing.
Any new videos?
What kind of guide keel is that?
it is A Avant Slot Guide Keel
Why not just take the interior out of the car
Nice work! Thank you!
way kool , thank you
Can you tell me where the tracks are here in Austin, Texas?
Read the stamp in the bottom left corner, he is based in New Zealand, I doupt he know many clubs in America
I am in Lubbock, and I am seriously thinking about getting something going here. Slot cars are on a come back and I am pleased to see it.
Nice build Sir.
Well done.
15:33 that laugh in the background tho
I heard that too
4:44 and 5:53 same video part in repeat?
Yeah what the heck
Hey Cobber , nice video,! You sell online?
what scale
+Cory Timm --- 1/32nd; AFAIK, Scalextric only makes 1/32nd scale.
+Veeter99 thanks
No they don't, Scalextric makes HO as well...
why not just buy a decent car, like a NSR or Slot it
Because it's called modelling; enjoying the challenge of modification and adaptation. Something creative as opposed to unimaginative cheque book "modelling" that you propose. Thumbs up to the original poster of this video.