I cleaned them with a little rubbing alcohol,let dry then wipe with a soft towel" without removal". It worked for me as I put in a large load,the sensor added 34 minutes B/C it was not dry. Before cleaning, 41 min. to 2 minutes in just 3 minutes total! Try this first!
Thank you! I ordered some replacement bars online and installed them today.. It now works great. I noticed that there was a little bit of lint buildup on the backside of the old sensors... To be honest, I kind of wonder if whether cleaning that would have fixed the problem. I went ahead and saved the old ones just in case they were still good. Either way, the dryer is now working great. Thank you for your video!
How can you tell if the part is not good? Can I put a tester on it or something else? My Amana dryer is showing a E5 code...I have changed the heater core, the thermistor and the fuse and put it all back together and it still shows the same code so I was thinking of the guide sensor
Can you clean the sensors, test them? They are passive metal pieces that could be coated with anti cling goop from dryer sheets. The sensors could be fine, but upstream Electronics or sensors could bed the problem.
while that white plastic lint frame is out, it is a good idea to vacuum out that area 'down below & or use a lint brush to get the lint out down in there
.. "If it's corroded or damaged and not sending a signal to the board." -Matt in the video However I agree that this is ridiculous. I bet if you thoroughly remove and clean it along with the assembly it will be good as new. Over time they probably get dirty or start to rust just enough that the delicate reading they send are slightly different.
Would this be causing the heat sensor to pop out? I have to take the back off the dryer and pop the heat sensor button back in before every load and then it will heat again
It's possible. I would start with trying to thoroughly clean the sensor to see if that helps. Dryer sheets are notorious for coating the sensors. If that doesn't help give us a call and we'll help you figure out what's causing the problem. We offer free technical advice and diagnosis. You can give us a call at 1-877-477-7278 or you can chat us at our website: www.appliancepartspros.com/. We will need your model number to give you accurate advice, which you can locate using this tool on our website: www.appliancepartspros.com/modelnumber_locator.aspx
It ended up being the heating coils. The temperature was coming up to 129, not enough heat to drying in 40 minutes. After replacing the coils the heat is now coming up to 140+.
I don't understand your question, however, we'd be happy to help you out with whatever you need to know. We offer free technical advice and diagnosis. You can give us a call at 1-877-477-7278 or you can chat us at our website: www.appliancepartspros.com/. We will need your model number to give you accurate advice, which you can locate using this tool on our website: www.appliancepartspros.com/modelnumber_locator.aspx
If you mean the wires at 1:50 in the video, they should simply come off when you tug them. Can you tell what's causing the resistance? Are they gunked up with anything, maybe?
That depends a lot on the model, as the replacement won't be the same in different brands and models. You can give us a call at 1-877-477-7278 or you can chat us at our website: www.appliancepartspros.com/. We will need the model number for the appliance, so that we can look up the part and how to go about the repair. If we have a repair video for that, we'll give it to you too.
Auto-dry is not working on my whirlpool dryer. I went into diagnostic mode to check for error codes and there is none. Could this still be a problem with the sensor? Is the fault code supposed to register correctly? I am concerned there could be another problem since the fault code is not coming up.
We'd be happy to help you out with that! We offer free technical advice and diagnosis. You can give us a call at 1-877-477-7278 or you can chat us at our website: www.appliancepartspros.com/. We will need your model number to give you accurate advice, which you can locate using this tool on our website: www.appliancepartspros.com/modelnumber_locator.aspx
I have a Maytag Intellidry Dryer (model LDE8606ACE). It recently has stopped automatically shutting off during the Intellidry setting. It drys, but won't shut off. It works on the timed setting, just not the Intellidry setting. Is it a bad moisture sensor? If so, where is it located and how do I change it? (I'm pretty handy, don't be scared.)
Like the dryer in the video the sensor is right inside the door. You can try taking it off and cleaning behind it and cleaning the metal strips, also check all the wire connections. If it still does not work it may be one of the controls. You can post the problem along with the appliance model number on our repair forum and the techs can help you troubleshoot the problem. forum.appliancepartspros.com/
Is it the grill cover that you're having a hard time removing? It may help to use your phone to take a few pictures of the inside, from the same angle we have our camera placed. That way you can see where all the screws are and make sure that you have removed them all.
I was able to look up the grill cover for your model. It looks a different than the one in this video, but it looks like it also has three screws that need to be removed, one on each side and one in the middle. Once those three screws are removed, it should be able to be pulled free. Here's a video where we replace a similar lint filter cover: ua-cam.com/video/J_lJJYyCoE0/v-deo.html . As you can see, Matt has to push forward to get it to pop free. If it's not coming loose, I would think it's because it's gunked up with build up from dryer sheets and the like.
I cleaned them with a little rubbing alcohol,let dry then wipe with a soft towel" without removal". It worked for me as I put in a large load,the sensor added 34 minutes B/C it was not dry. Before cleaning, 41 min. to 2 minutes in just 3 minutes total! Try this first!
God bless UA-cam repair mechanics
Thank you! I ordered some replacement bars online and installed them today.. It now works great. I noticed that there was a little bit of lint buildup on the backside of the old sensors... To be honest, I kind of wonder if whether cleaning that would have fixed the problem. I went ahead and saved the old ones just in case they were still good. Either way, the dryer is now working great. Thank you for your video!
How do you know if you need to replace BOTH sensors? Would there be any signs of wear and tear visible?
Gillian Carbone wondering the same thing
@@michelleciccio9627 if they are corroded.
How can you tell if the part is not good? Can I put a tester on it or something else? My Amana dryer is showing a E5 code...I have changed the heater core, the thermistor and the fuse and put it all back together and it still shows the same code so I was thinking of the guide sensor
Can you clean the sensors, test them? They are passive metal pieces that could be coated with anti cling goop from dryer sheets. The sensors could be fine, but upstream Electronics or sensors could bed the problem.
while that white plastic lint frame is out, it is a good idea to vacuum out that area 'down below & or use a lint brush to get the lint out down in there
Can I tie the wires together and bypass it? One of the bars got snagged and pulled out.
what does it mean if when you hit start the dryer doesnt come on and the sensing light does
I replaced mine. But it didn’t work. Same thing. Dryer goes from 41 min to 19 and 2 all in a few minutes. Maybe the thermostat?
This is exactly what mine is doing, have replaced the heater coil and thermostats already
Check the entire exhaust path from the lint screen to the vent outside. If clogged with lint the path gets too hot and the dryer shuts off.
How does a metal strip go bad? There are no solid state materials present.
.. "If it's corroded or damaged and not sending a signal to the board." -Matt in the video
However I agree that this is ridiculous. I bet if you thoroughly remove and clean it along with the assembly it will be good as new. Over time they probably get dirty or start to rust just enough that the delicate reading they send are slightly different.
Can you delete those sensors? My cloth always wet??
Hi 👋🏻 How to test this sensor?
Would this be causing the heat sensor to pop out? I have to take the back off the dryer and pop the heat sensor button back in before every load and then it will heat again
You could be having an issue with the thermostat or the fuse maybe. Do you happen to have a multimeter?
@@appliancepartspros I don’t 🫤
I can’t get the moisture sensor to disconnect from the wire
The cloths sometimes are still wet after drying. Is this the sensor?
It's possible. I would start with trying to thoroughly clean the sensor to see if that helps. Dryer sheets are notorious for coating the sensors. If that doesn't help give us a call and we'll help you figure out what's causing the problem. We offer free technical advice and diagnosis. You can give us a call at 1-877-477-7278 or you can chat us at our website: www.appliancepartspros.com/. We will need your model number to give you accurate advice, which you can locate using this tool on our website: www.appliancepartspros.com/modelnumber_locator.aspx
It ended up being the heating coils. The temperature was coming up to 129, not enough heat to drying in 40 minutes. After replacing the coils the heat is now coming up to 140+.
My do the same just clean the tube
will cause dry to run then shut off couple minutes and start
I don't understand your question, however, we'd be happy to help you out with whatever you need to know. We offer free technical advice and diagnosis. You can give us a call at 1-877-477-7278 or you can chat us at our website: www.appliancepartspros.com/. We will need your model number to give you accurate advice, which you can locate using this tool on our website: www.appliancepartspros.com/modelnumber_locator.aspx
Thank you - great video - It really is an easy repair : )
The wire connection on mine won't come off. You easily pulled yours off mine not so easy, I been trying to take it off for the last hour
If you mean the wires at 1:50 in the video, they should simply come off when you tug them. Can you tell what's causing the resistance? Are they gunked up with anything, maybe?
My dryer works well, but the end of cycle bell is not working. The sound display to turn off and on also does not make any sound. Easy fix or not?
That depends a lot on the model, as the replacement won't be the same in different brands and models. You can give us a call at 1-877-477-7278 or you can chat us at our website: www.appliancepartspros.com/. We will need the model number for the appliance, so that we can look up the part and how to go about the repair. If we have a repair video for that, we'll give it to you too.
Auto-dry is not working on my whirlpool dryer. I went into diagnostic mode to check for error codes and there is none. Could this still be a problem with the sensor? Is the fault code supposed to register correctly? I am concerned there could be another problem since the fault code is not coming up.
We'd be happy to help you out with that! We offer free technical advice and diagnosis. You can give us a call at 1-877-477-7278 or you can chat us at our website: www.appliancepartspros.com/. We will need your model number to give you accurate advice, which you can locate using this tool on our website: www.appliancepartspros.com/modelnumber_locator.aspx
My cloths have burn marks consistent with the shape of the moisture sensor, is this the cause or something else?
Why don't they sell these in pairs? How do you test which one is bad? 🤷♂️
They do, on Amazon
I have a Maytag Intellidry Dryer (model LDE8606ACE). It recently has stopped automatically shutting off during the Intellidry setting. It drys, but won't shut off. It works on the timed setting, just not the Intellidry setting. Is it a bad moisture sensor? If so, where is it located and how do I change it? (I'm pretty handy, don't be scared.)
Like the dryer in the video the sensor is right inside the door. You can try taking it off and cleaning behind it and cleaning the metal strips, also check all the wire connections. If it still does not work it may be one of the controls. You can post the problem along with the appliance model number on our repair forum and the techs can help you troubleshoot the problem. forum.appliancepartspros.com/
This is exactly my issue and I have same model. Did you find a solution?! Please let me know 🙏🏻🙏🏻
The housing won't come off. Why would that be?
Is it the grill cover that you're having a hard time removing? It may help to use your phone to take a few pictures of the inside, from the same angle we have our camera placed. That way you can see where all the screws are and make sure that you have removed them all.
AppliancePartsPros sorry yeah the grill cover. I removed the screws but o don't even hear it snap when I push it toward the drum.
What's your model number, Yaritza?
+AppliancePartsPros DV520AGP
I was able to look up the grill cover for your model. It looks a different than the one in this video, but it looks like it also has three screws that need to be removed, one on each side and one in the middle. Once those three screws are removed, it should be able to be pulled free. Here's a video where we replace a similar lint filter cover: ua-cam.com/video/J_lJJYyCoE0/v-deo.html . As you can see, Matt has to push forward to get it to pop free. If it's not coming loose, I would think it's because it's gunked up with build up from dryer sheets and the like.
how come he replace only one there's two in there
These are bs negitive ground