Mulțumesc pentru răspuns și detalii !te urmăresc mereu că am de învățat ,ești mai bun decât reprezentata din romănia respectiv cei din București care nu știu să citească o Diacnoză !
P0014 is an exhaust camshaft position sensor signal fault. There are two of these sensors (inlet and exhaust) at the top of the engine; very easy to change and not expensive. The part that you removed is the variable valve timing solenoid (VVT).
P0014 shows fault/issue with exhaust camshaft position and it is not necessarily sensor's fault. The way it works is as following. Sensor registers the position/angle of camshaft and sends the signal to ECU. ECU commands the solenoid valve to actuate, which should correct camshaft position. Sensor picks up new position and sends signal to ECU. Then ECU adjust command to solenoid as and when necessary, depending on some other sensors around engine). The whole process happens continuously every time engine runs. If ECU receives signal about bad camshaft position and throws a code there are two possibilities. 1/ 99% times it is a solenoid valve issue and it's unable to correct camshaft position 2/ extremely really is a sensor issue, on the way that sends corrupt signal to ECU Most of issues happen when inaccurate engine oil is used or there are too large intervals between oil changes and it causes solenoid valve to get stuck. If after clearing solenoid valve, performing an oil change and clearing engine code the issue doesn't return process that fault wasn't within sensor itself. Solenoid valve can be checked for operation during cleaning ( it either works or not) If valve operates well, and with cleaning enginee code doesn't resolve , then sensor would be the suspect I hope it clarifies All the best 👍
@mrfxr1695 Hi. I recently bought the car, and they said it had a full service history. However, it turns out its part service history. It hasn't had a service for 27k miles, which isn't great. I have changed the air filter and also the cabin filter. The fuel filter is a fuel filter for life. I will also fit new spark plugs. It is going in next week to have a service; oil change and filter etc. I did actually remove the VVT solenoid (exhaust side), and cleaned it. I didn't test it's operation though. I have ordered 2 new camshaft position sensors regardless as they are relatively cheap and easy to fit. I will also order 2 new VVT solenoids if needs be as the car is 13 years old.
@mrfxr1695 when you look at a replacement VVT solenoid, it appears that they have changed the design. The solenoid on my car (and yours) only has one filter ring. The newer solenoids all have 3 filter rings. I'm sure they will be fine as the dimensions are same.
@@stuartmcmillan7075 yes you're right, my one has only one filter ring. I never had to replace it, I've just cleaned it and change engine oil and oil filter. I assume they've changed design of replacement valves to better All the best 👍
Brilliant video,thank you,this fixed my 4 year old engine management light and the dreaded DEPOLUTION SYSTEM FAULTY warning,I’m well happy,still can’t believe it worked,keep up the good videos mate,👊🏻
Thanks 👍🙂, I'm glad it helped. These engines are very sensitive to incorrect or dirty engine oil and solenoid valves suffer a lot from it. All the best
Just got the light on myself and after this video I remembered I cleaned it a year ago as well. I'll reclean it and otherwise replace it. Thanks so much for your clear video!
@@jethrosweb yes it is, by the air intake. It is for timing of intake valves. It's a bit harder to get to. P0014 code usually refers to exhaust solenoid valve . I've got one video on the channel where I'm changing valve cover gasket and position of intake solenoid valve is shown there
I've also changed oil and oil filter, and it's all good now. Since it's using oil to adjust variable timing it is very sensitive to good oil level, viscosity and cleanliness
I've used 5w30 fully synthetic oil. I'm based in south of England so winter temperatures don't go below -5, if car is used in cold areas below-15 , I would use 0w30 grade for sure
One on the back controls variable timing of intake camshaft. As in aware both solenoid valves are identical to each other and share same part number All the best 👍🙂
mine 207cc got p0011 code . its a same problem? In the morning when the car is cold, it loses power on the first go. When it starts up again, everything is fine.
Yes, that code refers to variable timing as well. Then engineered are oil sensitive. Old, dirty or incorrect grade oil can cause it. When was the service done? If it was a while ago, try to change engine oil and filter and clean solenoid valves. As you said, problem is on start up, it could be oil related, oil pump might struggle to archive correct pressure/flow needed for solenoid valves. Hopefully fresh oil cold solve it
@ oil and oil filter changed like 1000km ago(oil 10w-40) i think its okay . maybe its time to service both solenoids. car only driven 120k km. i ordered today both solenoids . I'll change it tomorrow and see.
@@temmmmmm8415 thanks for the update. Please let us know how it goes tomorrow Also, I believe correct oil for 1.6vti is 5w-30 Main difference is 5W-30 This oil has a lower viscosity at low temperatures, so it flows more easily when starting a cold engine. It can still flow at temperatures as low as -22°F. 10W-40 This oil has a higher viscosity at low temperatures, so it might not flow as well when starting a cold engine.
@@mrfxr1695 yes, of course I will write the result. If I don't see any results, I will change the oil and filter again to 5w 30. worth a try. and plus I'm sure I have a fuel filter that needs replacing. But I can't find where it is. Do you have any info? I hope it's not in the fuel tank.
Thanks for the video! I am getting p0010 on 308 1.6vti which is the intake variable timing solenoid. Unfortunately I cannot find it, could you please guide me? Thanks
Hi here there, yes intake solenoid is literally on opposite side of the engine(back). It looks the same. You'll have to take air filter housing off to access it. It is simple enough, just few more screws If you see my video about head cover gasket replacement, ua-cam.com/video/e3DXi5sUKAs/v-deo.html it is shown there All the best 👍
@@herethereandsomewhere6755 have you managed to clear the code with obd diagnostic tool after replacement? Also have you changed engine oil, an old oil can cause malfunctioning of these valves sometimes as well
If this has gone will this cause smoke and lack of acceleration currwntly got 2010 with smoke blue smoke not alot only wen stationed for few mins at lights then clears up trying to break it down lol
i recently had the timing belt and sump cleaned and the engine light was not removed. Could error P0014 be related to the work done relating to this work done which was supposed to resolve errors P15A8 at all? Is the work the mechanic carried out incomplete?
I'm not sure to be honest. I beleive you mean timing chain and sump. What was the reason for cleaning it? These engines have variable timing and P0014 refers to exhaust cam shaft solenoid valve that is using engine oil to operate . Dirty oil or wrong viscosity can often cause this issue. The best would be to speak to your mechanic and see. It might just be a coincidence
Hello. I have a Peugeot like this. I watched a lot of your videos that solved my problems. With my car, it happens that the revs fluctuate while the engine is cold. Also when it warms up but less so. Can you help me? Thanks in advance!
I believe it is located on top of the tank, next to tank lid (under the rear seat with all wires and hoses ) that could also be a solution for your rev issue
@@mrfxr1695 what about variable torque, when engine is cold? I know, many questions, but i think the problem is in the solenoid on shaft or pedal trottle...
Hello, I know this engine has 2 solenoids. This one that you removed here is it Exhaust tai Inlet solenoid? Also, do you know the location of the second solenoid? Is it hard to acces? Thanks
They both texted to solenoid valve and timing. The valve is very sensitive to old, dirty or incorrect grades of engine oil. Usually, cleaning sorts it out
Hi, nice video! I need to try this, but in mine 207cc when the oil heats up to 90 degrees the engine starts jerk a bit and lose power. Did you have these symptoms? Of course I also have p0014 error and deppolution system faulty check engine. Sorry for my English, Im from Poland 😅
@@mrfxr1695 Hi, I was in the service, for sure I replaced solenoid for new original one and... it helps!!! Thank you so so much, again I have joy when I drive this car. I can't wait for summer when i will open the roof. All the best !
Mulțumesc pentru răspuns și detalii !te urmăresc mereu că am de învățat ,ești mai bun decât reprezentata din romănia respectiv cei din București care nu știu să citească o Diacnoză !
Thanks 👍🙂
@@mrfxr1695 👍
P0014 is an exhaust camshaft position sensor signal fault. There are two of these sensors (inlet and exhaust) at the top of the engine; very easy to change and not expensive.
The part that you removed is the variable valve timing solenoid (VVT).
P0014 shows fault/issue with exhaust camshaft position and it is not necessarily sensor's fault. The way it works is as following.
Sensor registers the position/angle of camshaft and sends the signal to ECU. ECU commands the solenoid valve to actuate, which should correct camshaft position. Sensor picks up new position and sends signal to ECU. Then ECU adjust command to solenoid as and when necessary, depending on some other sensors around engine). The whole process happens continuously every time engine runs.
If ECU receives signal about bad camshaft position and throws a code there are two possibilities.
1/ 99% times it is a solenoid valve issue and it's unable to correct camshaft position
2/ extremely really is a sensor issue, on the way that sends corrupt signal to ECU
Most of issues happen when inaccurate engine oil is used or there are too large intervals between oil changes and it causes solenoid valve to get stuck.
If after clearing solenoid valve, performing an oil change and clearing engine code the issue doesn't return process that fault wasn't within sensor itself.
Solenoid valve can be checked for operation during cleaning ( it either works or not)
If valve operates well, and with cleaning enginee code doesn't resolve , then sensor would be the suspect
I hope it clarifies
All the best 👍
@mrfxr1695 Hi. I recently bought the car, and they said it had a full service history. However, it turns out its part service history. It hasn't had a service for 27k miles, which isn't great.
I have changed the air filter and also the cabin filter. The fuel filter is a fuel filter for life. I will also fit new spark plugs. It is going in next week to have a service; oil change and filter etc.
I did actually remove the VVT solenoid (exhaust side), and cleaned it. I didn't test it's operation though. I have ordered 2 new camshaft position sensors regardless as they are relatively cheap and easy to fit. I will also order 2 new VVT solenoids if needs be as the car is 13 years old.
@mrfxr1695 when you look at a replacement VVT solenoid, it appears that they have changed the design. The solenoid on my car (and yours) only has one filter ring. The newer solenoids all have 3 filter rings. I'm sure they will be fine as the dimensions are same.
@@stuartmcmillan7075 yes you're right, my one has only one filter ring. I never had to replace it, I've just cleaned it and change engine oil and oil filter. I assume they've changed design of replacement valves to better
All the best 👍
@@stuartmcmillan7075 Did you buy these items online? And would you tell me where?
Brilliant video,thank you,this fixed my 4 year old engine management light and the dreaded DEPOLUTION SYSTEM FAULTY warning,I’m well happy,still can’t believe it worked,keep up the good videos mate,👊🏻
Thanks 👍🙂, I'm glad it helped. These engines are very sensitive to incorrect or dirty engine oil and solenoid valves suffer a lot from it.
All the best
Straightforward Video, hopefully to cure the P0014 fault. Thanks....
All the best👍
Just got the light on myself and after this video I remembered I cleaned it a year ago as well. I'll reclean it and otherwise replace it. Thanks so much for your clear video!
Thank you
All the best👍
Isn't there a second one on the backside of the motor/engine?
@@jethrosweb yes it is, by the air intake. It is for timing of intake valves. It's a bit harder to get to. P0014 code usually refers to exhaust solenoid valve . I've got one video on the channel where I'm changing valve cover gasket and position of intake solenoid valve is shown there
@@mrfxr1695 thank you captain
I have the same problem with my car P0014. What do you think I should do, should I buy a new part or should I try cleaning it?
Best ragads Ahmet
I always try to clean it first and also change engine oil ( dirty or incorrect oil viscosity can cause the issue)
All the best 👍
Great video, i have similar fault, bought a new sensor but still same error... Could you recommend a particular brand to buy
I can't recommend any, but usually you can't go wrong with major brands
Hi, happens the same to me. Have you solved it?
Very informative video. Thank you.
Thanks 👍
Bravo. Foarte de folos informatiile 🙏
Thanks 👍
Hi , well, you used some brake fluid to clean the VVT, what about Carburator cleaner fluid? Why did u use Brake Fluid?
Hi I didn't use brake fluid, I've used brake cleaner because I've run out of carburettor cleaner 👍
@@mrfxr1695 well I meant brake cleaner spray..
Lichidul de curățat carburatoare nu atacă cauciucul? Din clip am văzut soluție de spălată discuri și am procedat și eu la fel a fost ok
Hi mate thanks for your video, I have the same problem P0014 can you let us know if your car is running better or is it better to buy a new sensor ?
I've also changed oil and oil filter, and it's all good now. Since it's using oil to adjust variable timing it is very sensitive to good oil level, viscosity and cleanliness
@@mrfxr1695 could you tell me which oil did you use Thank-you
I've used 5w30 fully synthetic oil. I'm based in south of England so winter temperatures don't go below -5, if car is used in cold areas below-15 , I would use 0w30 grade for sure
There is a solenoid on the back of the engine as well....does that one do the same jobb?
One on the back controls variable timing of intake camshaft. As in aware both solenoid valves are identical to each other and share same part number
All the best 👍🙂
mine 207cc got p0011 code . its a same problem? In the morning when the car is cold, it loses power on the first go. When it starts up again, everything is fine.
Yes, that code refers to variable timing as well. Then engineered are oil sensitive. Old, dirty or incorrect grade oil can cause it. When was the service done? If it was a while ago, try to change engine oil and filter and clean solenoid valves. As you said, problem is on start up, it could be oil related, oil pump might struggle to archive correct pressure/flow needed for solenoid valves. Hopefully fresh oil cold solve it
@ oil and oil filter changed like 1000km ago(oil 10w-40) i think its okay . maybe its time to service both solenoids. car only driven 120k km. i ordered today both solenoids . I'll change it tomorrow and see.
@@temmmmmm8415
thanks for the update. Please let us know how it goes tomorrow
Also, I believe correct oil for 1.6vti is 5w-30
Main difference is
5W-30
This oil has a lower viscosity at low temperatures, so it flows more easily when starting a cold engine. It can still flow at temperatures as low as -22°F.
10W-40
This oil has a higher viscosity at low temperatures, so it might not flow as well when starting a cold engine.
@@mrfxr1695 yes, of course I will write the result. If I don't see any results, I will change the oil and filter again to 5w 30. worth a try. and plus I'm sure I have a fuel filter that needs replacing. But I can't find where it is. Do you have any info? I hope it's not in the fuel tank.
@@temmmmmm8415thanks, fuel filter is located in front of the fuel tank underneath the car, rh side
Thanks for the video! I am getting p0010 on 308 1.6vti which is the intake variable timing solenoid. Unfortunately I cannot find it, could you please guide me? Thanks
Hi here there, yes intake solenoid is literally on opposite side of the engine(back). It looks the same. You'll have to take air filter housing off to access it. It is simple enough, just few more screws
If you see my video about head cover gasket replacement,
ua-cam.com/video/e3DXi5sUKAs/v-deo.html
it is shown there
All the best 👍
Here is the video
ua-cam.com/video/e3DXi5sUKAs/v-deo.html
Thank you so much. Just replaced the solenoid but p0010 still here and the engine doesn't work as it should....
@@herethereandsomewhere6755 have you managed to clear the code with obd diagnostic tool after replacement? Also have you changed engine oil, an old oil can cause malfunctioning of these valves sometimes as well
There is actually 2of them. The other is at the back of the engine. Same side but at the back
True, there is the other one on the back of the engine, but that one is intake solenoid valve
What is involved in removing the Intake Solenoid ?
It's same thing just on the back side of the engine, you'll have to remove air fitter housing
If this has gone will this cause smoke and lack of acceleration currwntly got 2010 with smoke blue smoke not alot only wen stationed for few mins at lights then clears up trying to break it down lol
If you've got P0014 code than yes it is possible, but usually bluish smoke would indicate burning oil
@mrfxr1695 yeah think my stem seals have gone all good tho easy and cheap fix to do
I have tthe same car , i clean. the solenoid, .The error is still there, but my car now is working verry well.
Why the error is still there?
You have to clear the codes as well
@@mrfxr1695 after two days, the error dissaparread without erasing the error.
everyithing is good now
Hi there, my car is stuck in limp mode, only going to 3rd gear. Is the intake solenoid valve the problem or the oxygen sensor in such a case? Thanks
Automatic gearbox?
Any codes? P0768?
Yes, it an automatic gearbox. The code is P2196
i recently had the timing belt and sump cleaned and the engine light was not removed. Could error P0014 be related to the work done relating to this work done which was supposed to resolve errors P15A8 at all? Is the work the mechanic carried out incomplete?
I'm not sure to be honest. I beleive you mean timing chain and sump. What was the reason for cleaning it? These engines have variable timing and P0014 refers to exhaust cam shaft solenoid valve that is using engine oil to operate . Dirty oil or wrong viscosity can often cause this issue. The best would be to speak to your mechanic and see. It might just be a coincidence
Hello. I have a Peugeot like this. I watched a lot of your videos that solved my problems. With my car, it happens that the revs fluctuate while the engine is cold. Also when it warms up but less so. Can you help me? Thanks in advance!
I also can't find where the fuel filter is. It is not in the pump, not next to the pump or under the tank.
I believe it is located on top of the tank, next to tank lid (under the rear seat with all wires and hoses ) that could also be a solution for your rev issue
@@mrfxr1695 Thank you so much.
@@vladimirbjelic3442 all the best buddy
@@mrfxr1695 what about variable torque, when engine is cold? I know, many questions, but i think the problem is in the solenoid on shaft or pedal trottle...
Hello, I know this engine has 2 solenoids.
This one that you removed here is it Exhaust tai Inlet solenoid?
Also, do you know the location of the second solenoid? Is it hard to acces?
Thanks
Hi
As I'm aware that is exhaust solenoid. Inlet solenoid is on other side of the engine closer to firewall. They are identical
I hope it helps👍
@@mrfxr1695 thanks for reply!
Arabami stop edikden sonra bi kac saniye daha calisiyor hariza isik yanmiyor ne yspabilirim
önce OBD teşhis aracını takıp kodları okumanız gerekecek. Kendiniz yapamıyorsanız, lütfen saygın bir tamirciye götürün. Teşekkür ederim
Hi mate where’s the filter for this valve
It's on the valve itself, little mesh filter
can you tellme what is the code , i have the same car
It is P0014
P0013 and 0014 are on scanner
They both texted to solenoid valve and timing. The valve is very sensitive to old, dirty or incorrect grades of engine oil. Usually, cleaning sorts it out
Reinstalling the solenoid doesn’t click.
How to make sure it’s installed properly
It shouldn’t tilt?
👏👏👏👏
Cheers 🙂👍
Thats a oil control solenoid
Solenoid valve for variable timing of exhaust camshaft 👍
Prince engine is the Worst engine in the world
It is quite sensitive, it did have certain issues, but I've seen worse
@mrfxr1695 - my 208 GTi is dead after only 40k , timing chain, head gasket , thermostat ect , 4k to fix , not worth it
Hi, nice video! I need to try this, but in mine 207cc when the oil heats up to 90 degrees the engine starts jerk a bit and lose power. Did you have these symptoms? Of course I also have p0014 error and deppolution system faulty check engine.
Sorry for my English, Im from Poland 😅
Hi Mark
Yes, same symptoms. Sometimes solenoid needs cleaning and sometimes replacing. You'll have to clear the codes afterwards as well
All the best👍
@@mrfxr1695 Thanks for answer! Ok If that will works in my case you will be my hero haha. I let you know :) Have a nice day.
@@mrfxr1695 Hi, I was in the service, for sure I replaced solenoid for new original one and... it helps!!! Thank you so so much, again I have joy when I drive this car. I can't wait for summer when i will open the roof. All the best !
@@mark3556 all the best 👍🙂