XJ Anti-wrap bar install

Поділитися
Вставка
  • Опубліковано 28 сер 2024
  • We're showing you how to install the Heavy Duty Anti-wrap bar kit from Ruffstuff Specialties Part #R2300
    www.ruffstuffs...
    Check us out on IG and FB @trail__trash
    Get your Trail Trash merch here! trailtrash.mys...
    DISCLAIMER:
    Due to factors out of the control of Trail Trash, we cannot guarantee against improper use or unauthorized modifications of this information. Trail Trash assumes no liability or responsibility for property damages or injury incurred as a result of any information contained in this video. Use this information at your own risk. Trail Trash recommends safe practices when working on vehicles and/or with tools seen in this video. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Trail Trash. Be safe and happy Jeeping

КОМЕНТАРІ • 28

  • @Deckers_fab
    @Deckers_fab 3 роки тому +3

    I literally look forward to Y’all’s vids. Love it all. Slowly building on my xj as money allows

    • @trailtrash9717
      @trailtrash9717  3 роки тому +1

      We really appreciate that! We have a lot of new videos lined up it’s just a slow process to get them edited and build them at the same time haha.

  • @holdthatdown6695
    @holdthatdown6695 3 роки тому

    Sending my XJ love from New York keep up the good work bro

  • @praterbrothers4wd907
    @praterbrothers4wd907 3 роки тому

    I had to run one when I first went to tons and 40s. A had whee hop like no other. Destroyed a driveshaft once.

  • @ToddSalisbury
    @ToddSalisbury 3 роки тому

    Awesome video, great work, and teamwork!!!!!

  • @bryanrudy4625
    @bryanrudy4625 3 роки тому

    I like what y’all did with the body bracket and also the upper triangulated bar having the hiem and mount tab, Instead of the upper @ lower bars being welded to each other. I do wish you showed a little more detail on how the body bracket is welded onto the subframe. Question: what did you do with the EVAP canister?

    • @trailtrash9717
      @trailtrash9717  3 роки тому

      Thank you. I agree, I realized during editing that we didn’t really show how we made that bracket and attached it.. I don’t have any of the EVAP stuff since I swapped to the LS

    • @bryanrudy3161
      @bryanrudy3161 3 роки тому

      @@trailtrash9717 Im contemplating ditching my evap too. but cant find a vented gas cap for the tank. what did ya'll do?

    • @trailtrash9717
      @trailtrash9717  3 роки тому

      @@bryanrudy3161 I left the vent line under the hood so the tank can still vent. It just doesn’t go through the evap canister

    • @MrMrsregor
      @MrMrsregor Рік тому

      @@trailtrash9717 yea, i like this design!
      did you add your own hiem joint to the frame end of the upper bar and make your own bracket to mount it to the lower bar ?
      I like this design, but on their website it says it only comes with one hiem joint .?...

  • @keepinitr33l
    @keepinitr33l 2 роки тому

    You're going to want that traction bar on the passenger side. Right now, it's compounding drivetrain torque/lean and probably lifting the drivers side.
    On the passenger side, it will help combat engine torque/lean.

    • @trailtrash9717
      @trailtrash9717  2 роки тому +1

      Yeah and we knew this going in but it was easier to get it on the driver side and it is temporary until I do the 4 link

  • @jimmyburks7030
    @jimmyburks7030 Рік тому

    How did this work out, any regrets? I have this kit laying on my work bench. Any issues being on the driver side?

    • @trailtrash9717
      @trailtrash9717  Рік тому

      It really should be on the passenger side. With the amount of power it makes it really lifts the driver side under acceleration but this was temporary until I do my 4 link

    • @jimmyburks7030
      @jimmyburks7030 Рік тому

      @@trailtrash9717 same here, next step is 4 link.

  • @danhambrick6331
    @danhambrick6331 3 роки тому

    I think I would be replacing those RC leaf springs any way...

    • @trailtrash9717
      @trailtrash9717  3 роки тому

      If I didn’t already have some coilovers to go on it I would be replacing them. I got a few years out of them but they’re pretty tired

  • @courtneychappell8801
    @courtneychappell8801 2 роки тому

    America 🇺🇸Get her done boys

    • @courtneychappell8801
      @courtneychappell8801 2 роки тому

      I’m building a 96XJ right now trying to perfect my fabricating and welding skills 😖

  • @bradleyrodriguez4969
    @bradleyrodriguez4969 Рік тому

    What shackle did you get for body side?

  • @Hardlines_FullsendRc
    @Hardlines_FullsendRc Рік тому

    How has this mount held up??

    • @trailtrash9717
      @trailtrash9717  Рік тому +1

      It’s been working great and it’s been hit hard enough to bend the .250 wall lower tube

  • @alexfowler3249
    @alexfowler3249 2 роки тому

    How much rear stretch y’all running? What leaves and mounts did you use?

    • @trailtrash9717
      @trailtrash9717  2 роки тому

      It’s 5-6”. We made the front mounts ourselves and using the rough country shackle relocation brackets in the rear