How To Program A Cadillac CTS Smart Key Remote Fob 2015 - 2019
Вставка
- Опубліковано 4 вер 2024
- A step by step video on how to program a smart key remote fob to a 2015 - 2019 Cadillac CTS and CTS-V.
More free DIY programming instructions available at www.ProgramYou...
1. Remove the key lock cylinder cap. Insert the vehicle key into the key lock cylinder on the driver door handle; then turn the key counterclockwise, to the unlock position five times within 10 seconds.The Driver Information Center(DIC) displays REMOTE LEARN PENDING, PLEASE WAIT.
2. Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON TO LEARN, then press the ENGINE START/STOP button. (You may have to open and close drivers door to see the DIC display). The DIC display will again show REMOTE LEARN PENDING, PLEASE WAIT.
3. Repeat Step 2 two additional times. After the third time all previously known transmitters will no longer work with the vehicle. The DIC displays PRESS ENGINE START BUTTON TO LEARN, then press the ENGINE START/STOP button. (You may have to open and close drivers door to see the DIC display). Remaining remote key fobs can be relearned during the next steps. The DIC display should now show READY FOR REMOTE # 1.
4. Place the new smart key fob in the transmitter pocket with buttons facing the rear of the vehicle. The transmitter pocket is inside the center console storage area between the driver and front passenger seats. The storage area will need to be opened to access the transmitter pocket.
5. Press the ENGINE START/STOP button. When the transmitter is learned, the DIC display will show that it is ready to program the next remote key fob.
6. Remove the transmitter from the transmitter pocket and press unlock or lock on the transmitter.
To program additional transmitters, repeat Steps 4-6. When all additional transmitters are programmed, press and hold the ENGINE START/STOP button for approximately 12 seconds to exit programming mode.
I have a 2015 Cadillac CTS this video really helped me a lot I appreciate it thank you
You're Welcome! Glad it helped
I did this and it worked but I got some unexpected bonus material. After programming FOB1 the car prompted to program FOB2. I think maybe I didn't hold the start/stop button for an honest 12 seconds to exit programming mode.. After that, when I get into the car it doesn't want to start unless I once again hold the start button for 12 seconds. I can sit in the driver seat and repeatedly stop and start the engine. After I get out of the car, shut the door and the auto lock engages, then I unlock with the remote and get back in, it's the whole 12 second thing all over again along with the 'service theft deterrent system' message. So I'm having two minor inconveniences. The 12 second thing and trying to figure out how to reset the theft deterrent system.
programming a second remote should resolve both issues
Thank you for the video🙏🏼. I’m trying to work with these steps on my 2016 Cadillac CTS (a bit different than the model in your video). I finally got a new battery in my car after it sat for 2 years. The car will turn on while the fob is in the center console transmitter spot, but not with the fob buttons nor will it lock or unlock. SO I’m trying to reprogram the key, BUT because I have to open and close the door to get the dash to turn on, the alarm starts going off and it doesn’t seem to stop with a specific technic, it just stops eventually 🥴😩. I’m gonna take the fob to a key person tomorrow to see if something is wrong, but I’m just reaching out for help of anyone has had this issue.
It sounds like the battery is dead in the fob
I have a 2019 XTS an I have a key fob from a 2018 I previously owned how can I clear it, reset or put the 2018 key fob in pairing mode so I can program it to the 2019 XTS as spare key fob
These fobs lock to a vehicle once programmed and need to be unlocked by someone with the correct equipment before they can be programmed to different vehicle.
Is there a video for an additional fob if I already have one working fob?
You can use this procedure. If you look at the instructions that are in the description box for video, you will just repeat steps 4-6 for each remote. You will need to have your working remote far enough away from the car so it cant be read to get the vehicle into programming mode.
@@cad1995 You need to do the whole procedure just like the video and then when you get to step 6 ( but before you hold down the stop/start button to exit programming mode), go back to step 4 for each remote.
Hey there. Do you guys have a phone number? I have a mine boggling issue that would be best described over the phone. TIA
I bought my 2014 CTS V-Sport (same 3rd gen CTS and key fob as yours) with one remote only. This one remote seems to not be assigned a driver as my memory seats do not automatically go to position like they should. I have to manually push or hold (if in drive) the seat position number I want every time I drive the car. The easy exit feature works as expected. Should I follow this and essentially wipe and start over or is there another way to just tell the car my sole fob is for driver one?
You can use this procedure to re-program the remote that you have and it will set it as driver 1 as all previous remotes will be erased.
@@PYR-Auto So I just got a second key fob to have as a backup and was going to reset and have my first one as driver one and backup as driver two. When I did the five key swipes to the left, I got this message, "Ready for remote 4" How do I wipe out the current three which I do not have in my possesion?
How do you add a key programmed to a 2011 Cadillac cts coupe? I just want to add a spare to the original one I have. Thanks!!
We don't have a video for it yet but you can find the text instructions below. I believe on the coupe you need to use the key cylinder on the trunk instead of the drivers door. www.programyourremote.com/classified/2011-cadillac-cts-keyless-entry-remote-fob-smart-key-programming-instructions-listing-6800.aspx
I bought a '16 model and it only came with 1 fob witch works fine. I bought another one (used) on Ebay to have a spare, do I go through the same steps to program it as well?
On a 2016 CTS there is shorter procedure you can use if you already have 1 working key. You can find that here www.programyourremote.com/classified/2016-cadillac-cts-keyless-entry-remote-fob-smart-key-programming-instructions-listing-8575.aspx
I’m trying to work with these steps on my 2016 Cadillac CTS (a bit different than the model in your video). I finally got a new battery in my car after it sat for 2 years. The car will turn on while the fob is in the center console transmitter spot, but not with the fob buttons nor will it lock or unlock. SO I’m trying to reprogram the key, BUT because I have to open and close the door to get the dash to turn on, the alarm starts going off and it doesn’t seem to stop with a specific technic, it just stops eventually 🥴😩. I’m gonna take the fob to a key person tomorrow to see if something is wrong, but I’m just reaching out for help of anyone has had this issue?
you know that I have a little problem when I use lock button some doors donot close and the same problem when I use unlock button some doors donot open how can I solve this one?
Thanks for showing me how it's done. Very easy to follow your steps. New sub
Glad it helped, thanks for the sub!
What if you don't have the cut key? Can you still somehow enter programming mode to add a fob?
My friend lost hers but she has the second fob that works and only wants to add a new one.
You will need the emergency key to use the onboard programming procedure otherwise a dealer or locksmith will be needed
This might be dumb but I want to check -- let's say I have my original key fob key but my actual fob is trash, I do not need to get a new key cut correct? I can use that key but just a new fob?
Correct, you can just use your old emergency key with a new fob.
Not to keep beating a dead horse but since I have on remote already programmed, do I just start with steps 4-6 with the new remote and if so how do I get to the learn part in step 4 or do i need to start all over. Because when I put the new remote in the pocket, the screen is reading "No remote was detected".
Do the procedure just as its done it the video. When you get to step 6 (according to the instructions in the description box) but before you hold down the stop/start button to exit programming mode go back to step 4 for your "old" remote, you need to reprogram it back in. then when you're done adding remotes hold down the stop/start button for at least 12 seconds to exit programming mode. If you are already doing that and getting a message that says "no remote detected" during the procedure, then there may be an issue with the remote.
Will this work if I have a key fob from a salvaged vehicle?
No - these fobs lock to a vehicle once programmed and need to be unlocked before they can be programmed to a different vehicle.
Remote only works while in the transmitter. How can I get it to work without it being in there? Also remote will not lock or unlock the doors
The first thing to try would be to replace the battery in the key fob
What do I do if my car is not reading the fob. I have a 2016 CTS
If you are following the procedure closely, there could be an issue with the fob you are using
Hello, will this work for a 2015 CTS V with a built in ignition rather than a push start
If you're vehicle is not push button start, i don't believe it would work.
Will this process work also on a 2015 push start STS model
Are you sure that's what your vehicle is? looks like 2011 was the last year of the STS
What about adding a second key fob
There is a shorter procedure you can use if you already have at least one working fob. You can find that procedure in your owners manual or here www.programyourremote.com/classified/cts-browse-168.aspx
I had one of my key fobs stolen. If I do this will the stolen key have access to my car?
No - this procedure erases all previous keys
Does this work with a key fob I buy from Amazon
it can - if its the correct key fob
Would this work on a 2014 cts4??
This should work on a 2014 CTS sedan - but not coupe. Also, this will only work on a CTS that was built in the U.S.
How do i get the key cut?
automotive locksmith or delaership
How can i add remote for CTS 2015
as i turned the key 5 times to the left i won’t launch remote learning
This would be the only procedure - some vehicles only show that message for a few seconds right when the door is opened
@@PYR-Auto ypu mean even i don’t see the message i should continue the procedure?
Yeah - I would try just going off of the time rather than the messages. Also, if you have at least one working key there is a shorter procedure to add another one you can find those instructions here www.programyourremote.com/classified/2015-cadillac-cts-keyless-entry-remote-fob-smart-key-programming-instructions-listing-8574.aspx
You gotta know how to do it if it’s separate, there’s a certain way that you have to do it
seperate?
I know this is an old video. I hope you still check in on these comments though. My key is destroyed all I have is my cut key from it.
Does this mean I can buy a new remote transmitter and follow your steps and it should be fine? (It's a 2016 cts vsport) I'd hate to buy a transmitter and it not work for me.
Yes - you can use the emergency key out of an old key fob to program new key fobs
How do you program which remote number it is, like 1 or 2?
The order in which you program the fobs in determines what number the vehicles recognize them as. ( first remote programmed is driver one, second remote programmed in is driver 2, etc.) If you look at the steps in the description box of the video, you need to repeat steps 4-6 for each remote, after the first remote is programmed.
@@PYR-Auto yes but if you're replacing remote 1 because its malfunctioning how do you do that?
This procedure erases all the old remotes so whatever remote you program first will be the new driver 1