Thanks for this video. Fixed one of my SL-B202s today after picking up glue from Midwest. Another thing I learned is that flipped upside-down, they sit nicely on top of a 5-gallon bucket.
I can’t believe you posted this 3 days ago - and I just found a SL-B101 with this exact issue at the local recycling center/electronics dumpster! I snagged it before the trash attendants caught me. 🤣 Thank you sir for the awesome video! I’ll be doing this little project asap/tomorrow!
Update on my previous comment. I managed to open up my Technics SL-J11 motor. However, my motor was a much more simple design. Two things I noticed. The shaft bearing had a bit of play, but still manageable. The noise on mine seemed to come from the spindle bearing that was on the plastic motor cover. I couldn't manage to get those brushes out of the way without bending them, but they still work so it's fine. In the end it significantly reduced the grinding noise my motor had and it's very quiet now. Not silent, but night and day compared to what it was like previously. Those metal tabs are an absolute pain in the ass to open/remove and I didn't even bother with glue when mounting the motor back, it seemed to fit in there very tightly.
ARE YOU KIDDING ME? Wow, I have a Technics SL-J11 linear table that I wanted to gift to a friend, but the motor was making a similar noise. No matter how much I oiled the spindle the noise didn't seem to go away. It's very similar to the noise in your clip and I'm positive that this is the issue. I'll have a look at it tomorrow, but man, you're a lifesaver!
Great Vid, doing this now, i has some noise but I also have a very fast table almost 75RPM, you think changing that Hall IC chip also will help with why it’s running way too fast ?
Thanks so much for this instructional video! I do have a question about a small issue I am having with this repair. There is some friction in the motor housing. Is it possible that the glue that I applied to the underside of that metal washer raised the height slightly, causing it to rub against the inside of the white plastic motor housing after reassembly? The motor turns so smoothly before I reassemble it. And then there is friction and resistance and it doesn’t spin very smoothly after I snap the housing back together. Any advice or insight you can offer me? Thank you!
Ah, nevermind. I discovered the problem. One of the little brushes popped down when I resoldered the motor onto the board. It was rubbing against that washer. I didn’t realize the end of that brush was actually the solder point of the motor and can move somewhat freely within the plastic cover once you clean the solder off of it. Problem solved and it works great! Thanks again! 😊
Great video. I did this operation to mine a few years back and it still works well to this day.
100% correct. I discovered this fix myself (the hard way), you've made it easier for everyone else. Nicely done!
Thanks for this video. Fixed one of my SL-B202s today after picking up glue from Midwest. Another thing I learned is that flipped upside-down, they sit nicely on top of a 5-gallon bucket.
I can’t believe you posted this 3 days ago - and I just found a SL-B101 with this exact issue at the local recycling center/electronics dumpster! I snagged it before the trash attendants caught me. 🤣 Thank you sir for the awesome video! I’ll be doing this little project asap/tomorrow!
Update on my previous comment. I managed to open up my Technics SL-J11 motor. However, my motor was a much more simple design. Two things I noticed. The shaft bearing had a bit of play, but still manageable. The noise on mine seemed to come from the spindle bearing that was on the plastic motor cover. I couldn't manage to get those brushes out of the way without bending them, but they still work so it's fine. In the end it significantly reduced the grinding noise my motor had and it's very quiet now. Not silent, but night and day compared to what it was like previously. Those metal tabs are an absolute pain in the ass to open/remove and I didn't even bother with glue when mounting the motor back, it seemed to fit in there very tightly.
Thank you. I just got the same turntable and its making the same exact noise. Now i know how to fix it.
This helped with my b202. Much thanks
ARE YOU KIDDING ME? Wow, I have a Technics SL-J11 linear table that I wanted to gift to a friend, but the motor was making a similar noise. No matter how much I oiled the spindle the noise didn't seem to go away. It's very similar to the noise in your clip and I'm positive that this is the issue. I'll have a look at it tomorrow, but man, you're a lifesaver!
Wildly informative video! Excellent how-to tutorial.
Great video! Mine had the exact same issue and I was able to fix it in no time thanks to this video!
This is amazing. You are the man.
Great Vid, doing this now, i has some noise but I also have a very fast table almost 75RPM, you think changing that Hall IC chip also will help with why it’s running way too fast ?
Very good
Thanks so much for this instructional video! I do have a question about a small issue I am having with this repair. There is some friction in the motor housing. Is it possible that the glue that I applied to the underside of that metal washer raised the height slightly, causing it to rub against the inside of the white plastic motor housing after reassembly? The motor turns so smoothly before I reassemble it. And then there is friction and resistance and it doesn’t spin very smoothly after I snap the housing back together. Any advice or insight you can offer me? Thank you!
Ah, nevermind. I discovered the problem. One of the little brushes popped down when I resoldered the motor onto the board. It was rubbing against that washer. I didn’t realize the end of that brush was actually the solder point of the motor and can move somewhat freely within the plastic cover once you clean the solder off of it.
Problem solved and it works great! Thanks again! 😊
The turntable is a 1980s
model from Technics, right?
Yes
My turntable goes in reversr now, could it be the plastic piece on the motor put on the wrong way or the magnet flipped
I have the same issue, did you manage to fix it ? Thx
@@quentinbernaudon3193 yea I flipped the magnet but it was already damaged because of the chip
Sh**, that doesnt sound good for me… i’ll try tommorow
Thanks