Thanks for the video, you have shown me it is really very simple to change pressure if you are careful. This is similar to my engineering work. Thanks for taking the time to show us
It seems the same kind of design as Theoben use. Remove regulator, install a fast flow valve and increase hammer spring tension! Find the sweet spot and you'll have a good 20 full power shots before the power starts to curve along with a massive increase in power.
I own FX Gladiator MKII,6.35, 600mm barrel, regulated. I think the factory output pressure is set to 130-135 bars, not 160 as you've said. FX Boss is set to 160bar.
Any chancenof doing a video like this for the boss owners... we have been left out when it comes to these types of videos... I'd like to know exactly what I'm doing to adjust and repair my regulator.. and gun
So if I turn hammer spring clock wise my fps will go up? I have the fx bobcat mk2 in 30 I would like it to shoot between 850 and 900. How many full turns should I turn it?
Thanks for the video Ernest. Do you know of resources such as this for working on FX guns? I have both a Indy and Verminator Extreme and would like to do my own work when the warranty runs out.
hi there will the bobcat tube fit into the royal block adapter? my bobcats brass fill tube has failed at the welds which is common so id like to put the royal tube adapter on instead but remove the foster nipple in place of a microbore air hose to the rear filler and guage
Hi nice video my fx royale 400 air loss from the little hole next to the manometer i ask arizona airguns and is said need to replace the dowty seal but i dont where is locate that part can u explaint please or some body thanks
Is there a regulator for the royale 400 with the power adjustment or is the same for both models? Also where can i find one of those that eliminates most of the bell curve?? Thank you very much
Hello. how to unscrew the bronse regulating part? i need to take the whole regulator apart for replacing the o-rings inside - it leaking air throught the ventilation hole
All vidio footage on adding/ removing power from regulators on Fx Impact. Seem to already have a blank removed fron the screw. Mine has one and I am unsure if I am allowed to remove it to add preasure. Currently reading 25 on reg pressure. Any Ideas? Please
What a pain in the ass to do this. I guess things have changed a little bit since 2013... On the Impact you can do this without taking the gun apart. Right? Too bad I cannot do this "on the fly" with my 2016 Bobcak Mk2... Anyhow, thanks for posting.
Hello, my Royale 400 only about 850 w/ 16 gr. pellets. disappointed. What you say to do is loosen the loctite & turn the screw clk wise to increase the fps , is this correct. thanks.
Yes, this will change the power of your gun, but do not expect extreme changes in fps rates. Perhaps you can increase the speed up to 20-30 fps, which I did, however, if you need more speed you need more air pressure for more speed and the hammer spring of FX is not strong enough to push the valve harder.
This is only for fine tuning the velocity. If you want to increase the speed for 100m/sec or more ,you have to unscrew the locknut that holds the cup-washers tight, on the back of the regulator. Then fine tune with the hammerspring.
tornhill have you already installed it? i have a kit intstalled on my rifle as well. i bought my royale in Sweeden so it was 10j. Now is full power. if you need help i can help you
Thanks for the video, you have shown me it is really very simple to change pressure if you are careful. This is similar to my engineering work. Thanks for taking the time to show us
As always great videos. I look forward to your posts, they're extremely informative and very well made, thank you so much.
It seems the same kind of design as Theoben use. Remove regulator, install a fast flow valve and increase hammer spring tension! Find the sweet spot and you'll have a good 20 full power shots before the power starts to curve along with a massive increase in power.
I own FX Gladiator MKII,6.35, 600mm barrel, regulated. I think the factory output pressure is set to 130-135 bars, not 160 as you've said. FX Boss is set to 160bar.
Any chancenof doing a video like this for the boss owners... we have been left out when it comes to these types of videos... I'd like to know exactly what I'm doing to adjust and repair my regulator.. and gun
Great informative video, do you have any other suggestions on improving FX royale models?
So if I turn hammer spring clock wise my fps will go up? I have the fx bobcat mk2 in 30 I would like it to shoot between 850 and 900. How many full turns should I turn it?
On my bobcat I thought my regular was in the tube? I want to turn it up some.
Is it possible a review for the regulator and other parts on the fx wildcat 22 high power?
Thanks a lot.
Thanks for the video Ernest. Do you know of resources such as this for working on FX guns? I have both a Indy and Verminator Extreme and would like to do my own work when the warranty runs out.
hi there will the bobcat tube fit into the royal block adapter? my bobcats brass fill tube has failed at the welds which is common so id like to put the royal tube adapter on instead but remove the foster nipple in place of a microbore air hose to the rear filler and guage
So what is regulator pressure setting for .25 cal Royale?
Thank you 👍🏻👍🏻👍🏻👍🏻
Hi nice video my fx royale 400 air loss from the little hole next to the manometer i ask arizona airguns and is said need to replace the dowty seal but i dont where is locate that part can u explaint please or some body thanks
Your videos are cool and I see you know a lot about airguns,regulators etc.. thumb up
I have FX bobcat MK2 in.25 cal, can i remove sylender with out degas the airgun
Is there a regulator for the royale 400 with the power adjustment or is the same for both models?
Also where can i find one of those that eliminates most of the bell curve??
Thank you very much
Hello.
how to unscrew the bronse regulating part?
i need to take the whole regulator apart for replacing the o-rings inside - it leaking air throught the ventilation hole
please show us how to adjust the fx regulator. I need to adjust my wildcat regulator
All vidio footage on adding/ removing power from regulators on Fx Impact. Seem to already have a blank removed fron the screw. Mine has one and I am unsure if I am allowed to remove it to add preasure. Currently reading 25 on reg pressure.
Any Ideas? Please
is this the same princaple on a fx varminator
Hi, can you tell me the exact dimensions of the FX Boss block?
Length, height and width please.
Thanks so much
Hello friend
How do you take the stock off of the my 2 Bobcat please ?
is there a way to take off the stock ldc?
Hi. can I shoot my Bobcat mkII below the reg pressure? 145 bar. Or will it damage the system ?!
Thanks!
What a pain in the ass to do this. I guess things have changed a little bit since 2013... On the Impact you can do this without taking the gun apart. Right? Too bad I cannot do this "on the fly" with my 2016 Bobcak Mk2... Anyhow, thanks for posting.
thank you for share :) keep it up please
help me please
i have FX royale 500 6.35 its too slow and week even on the maximum power
power adjuster is not a solution
does this regulator work for FX Gladiator? thanks
Good job!
Hello, my Royale 400 only about 850 w/ 16 gr. pellets. disappointed. What you say to do is loosen the loctite & turn the screw clk wise to increase the fps , is this correct. thanks.
Yes, this will change the power of your gun, but do not expect extreme changes in fps rates. Perhaps you can increase the speed up to 20-30 fps, which I did, however, if you need more speed you need more air pressure for more speed and the hammer spring of FX is not strong enough to push the valve harder.
This is only for fine tuning the velocity. If you want to increase the speed for 100m/sec or more ,you have to unscrew the locknut that holds the cup-washers tight, on the back of the regulator. Then fine tune with the hammerspring.
Useless. How do I adjust the regulator on my Bobcat. You only showed how to remove it. I need to bring it back to 130 bar as it is 120.
Hi. Just got a FX Royale 500 and looking for instructions how to mount the high power kit I got. Anyone know a good tutorial?
tornhill have you already installed it? i have a kit intstalled on my rifle as well. i bought my royale in Sweeden so it was 10j. Now is full power. if you need help i can help you
If you need help let me know, i'm sure i can help you. I've installed it myself on my Royale 400
Jag har inte installerat det ännu. Tänkte göra det under helgen. Alla tips är välkomna då jag inte hittat någon instruktion.
lol i did not understood anything. i'm not Swedish. I just bought the rifle there but i can help you anyways
done!
Does anyone knows the size of the o-rings??
11,6x2,4mm