Slipping Clutch Kickstart - Clutch Adjustment Semi Auto Honda Engine CT70 Z50 Mini Trail Monkey Dax

Поділитися
Вставка
  • Опубліковано 24 гру 2024

КОМЕНТАРІ • 66

  • @dannilaser16
    @dannilaser16 Рік тому +3

    Awesome video.
    One of the best on UA-cam.
    Thank you for sharing.

  • @wildman3541
    @wildman3541 28 днів тому

    Thanks for showing this. My 81 kick starter is very easy to kick and not moving piston. Going to try this procedure. Wildman RG3

  • @DougieeStyle
    @DougieeStyle 2 роки тому +1

    6:50 you meant to say *clockwise*. Thank you for the video very helpful!

  • @michaelandmariedownes6070
    @michaelandmariedownes6070 4 місяці тому

    Thank you. I had no idea that JASO-MA was pertaining to wet clutch suitibility.

  • @jasonhendrie5411
    @jasonhendrie5411 4 роки тому +3

    This is just what I need my 83 ct70 kickstarter is slipping

  • @keithstewart4750
    @keithstewart4750 3 роки тому +2

    Thanks. New clutch fibers and my clutch grabs so it won’t idle. I turned it back CCW to resistance and it’s better, not great, but shifting get sticky. Also when shifter is held down or up I can still feel some clutch engagement . Any other ideas it could be?

    • @nealblackburn8628
      @nealblackburn8628 2 роки тому

      it is probably revving too much on idle when that happens the cen trif e cal weights are starting to do there job so if you can't slow the idle down a bit you need to start looking at motor tune

  • @seffdog1177
    @seffdog1177 3 роки тому +2

    Good tip about the car oil compared to bike oil

    • @katkylekim
      @katkylekim 2 роки тому +1

      True ,not many can give a good explanation especially when some say just put any oil in it and it will still go !!!

    • @markhaney3994
      @markhaney3994 6 місяців тому

      Almost. The motorcycle oil has a friction modifier, not the other way around.

  • @opinion4246
    @opinion4246 2 роки тому +4

    Thanks very helpful👍

  • @stevebuckmaster13
    @stevebuckmaster13 2 роки тому +2

    Josh , Another great video, my bike is doing the same thing, sometimes it has compression and sometimes not , i will try these and see what happens . Did you get my tip i sent you ?
    Thanks again

  • @irocss85
    @irocss85 2 роки тому

    I just bought a used pit bike 110cc I've heard there all the same. My stud WILL NOT TURN either way with the nut completely off. I wanted to adjust it because it bangs into gear hard from neutral even after lowering the idle. I did change the oil. And possibly at some point it had the wrong oil in it. But that wouldn't explain why the stud is stuck. How do you replace that? Mines a tao tao pitbike. Not sure where to get that part and the side cover gasket.

  • @chavasrt4428
    @chavasrt4428 Рік тому

    helo any idea why my z50r wont move under its own power even on first gear ?

  • @SergeoGabrielloGomez
    @SergeoGabrielloGomez 2 роки тому

    Best way to replace that little adjust stud ?

  • @johnsn10
    @johnsn10 10 місяців тому

    My 2017 crf50 moves on its own when put in gear and the idle is set correctly. It sat for 2 years so could it be stuck clutch plates? If I put the bike on a stand and put it in gear the rear wheel starts spinning and I can’t stop it.

    • @megastick9324
      @megastick9324 4 місяці тому

      Does it stop when you push the shifter down and hold it down? That engages the clutch, letting off engages it, that how it works. It disengages the clutch and shifts at the same time, when you let of it engages , like letting out the clutch on a standard shift.

  • @MrMasterFlash
    @MrMasterFlash Рік тому +1

    6:50 You said counterclockwise when you should've said clockwise, right?

  • @troycotsenmoyer6736
    @troycotsenmoyer6736 2 роки тому

    Can you tell by looking at the adjusting screw for the clutch if your clutch plates are worn?

    • @VintageHondaMinis
      @VintageHondaMinis  2 роки тому +1

      New plates adjusted, are a 1/4 turn out from ccw full lock on adj stud. As clutch fibers wear you make cw turns to adjust for wear. If you are almost all the way cw with adjustment stud and have slipping etc...time to replace clutch fibers.

    • @troycotsenmoyer6736
      @troycotsenmoyer6736 2 роки тому

      @@VintageHondaMinis Thank you sir

    • @troycotsenmoyer6736
      @troycotsenmoyer6736 2 роки тому

      Will the adjustment stud show more threads with new friction plates?

    • @VintageHondaMinis
      @VintageHondaMinis  2 роки тому

      @@troycotsenmoyer6736 yes, b/c you turn it out CCW to set inital grab

  • @johntucker9346
    @johntucker9346 2 роки тому +9

    why are your finder nails painted

    • @markhaney3994
      @markhaney3994 6 місяців тому

      Mind your business son

    • @johntucker9346
      @johntucker9346 6 місяців тому

      @@markhaney3994 son ffs look kid grow up

    • @monkeysbnb529
      @monkeysbnb529 5 місяців тому +1

      Why do you have a problem with it?

    • @patdttr225
      @patdttr225 Місяць тому

      @@monkeysbnb529lighten up, he just asked a question. Guys don’t normally wear nail polish, hence the reasonable question.

  • @bensmith8125
    @bensmith8125 3 роки тому

    What if the stud won't turn to the left or right?

    • @VintageHondaMinis
      @VintageHondaMinis  3 роки тому +1

      If you loosen the 14mm nut It should. Maybe time to pull cover and see what is going on.

    • @bensmith8125
      @bensmith8125 3 роки тому

      @@VintageHondaMinis i just rebuilt the clutch. Loosened all the clutch cover bolts and it freed up. Thanks.

  • @notagain8661
    @notagain8661 2 роки тому +7

    Dude, at least touch up with nail polish when making a video. 😒

  • @Jonesie170
    @Jonesie170 2 роки тому

    Should you do the adjustment after the engine is warmed up? thanks

    • @VintageHondaMinis
      @VintageHondaMinis  2 роки тому

      Baseline adjustment cold is fine. Make a fine adjustments as needed.

  • @johnsn10
    @johnsn10 2 роки тому +5

    The painted fingernails are distracting

  • @5yri5
    @5yri5 2 роки тому

    Thank you

  • @myleslong9326
    @myleslong9326 4 роки тому +8

    What’s with the fingernails

    • @VintageHondaMinis
      @VintageHondaMinis  4 роки тому +16

      My 5 year daughter old painted them. No shame LOL

    • @Jack_DeRipper
      @Jack_DeRipper 4 роки тому +5

      As the father of a daughter, I absolutely believe you. 🙂

    • @jimg2885
      @jimg2885 3 роки тому

      @@VintageHondaMinis I thought the left hand was the red 69 z50 and the right hand was the blue z50. You do need to touch them up. lol

    • @patdttr225
      @patdttr225 Місяць тому

      @@VintageHondaMinisright on!

  • @mmetz1877
    @mmetz1877 Рік тому +1

    Dude, what’s with the nail polish?

  • @simmosimmo100
    @simmosimmo100 Рік тому +3

    Stop with the nail varnish.

    • @VintageHondaMinis
      @VintageHondaMinis  Рік тому +2

      Don't worry I didn't transition, I snapped out of it.

    • @simmosimmo100
      @simmosimmo100 Рік тому

      @@VintageHondaMinis Glad to hear it. Good response.

    • @monkeysbnb529
      @monkeysbnb529 5 місяців тому

      You have a problem with his way of life? Move on

  • @jamesbeaumont1202
    @jamesbeaumont1202 3 роки тому +22

    Painted nails what's all that about

  • @NshsShdh-jx9ob
    @NshsShdh-jx9ob Рік тому

    ♥️👍🥰🥰🥰🥰👍👍👍👍

  • @bradjohnson8100
    @bradjohnson8100 7 місяців тому

    Very clear instruction but the fact that a man is wearing fingernail polish is weird. Hope that the Lord grants you repentance.

    • @monkeysbnb529
      @monkeysbnb529 5 місяців тому

      What does the “lord” have to do with anything? F off

  • @chadcourt4211
    @chadcourt4211 4 роки тому

    dude your 14 mm is 13mm

    • @VintageHondaMinis
      @VintageHondaMinis  4 роки тому

      Yeah this nut is not a factory nut. Should of said something but didnt think my camera would pick it up so clearly - Oh well. You'll need a 14mm for the factory nut.

  • @prcaroo1
    @prcaroo1 8 місяців тому

    Y do u have painted nails 🤔

  • @MrMasterFlash
    @MrMasterFlash Рік тому

    4:28 you say 14mm nut but then the wrench says 13mm on it. No big deal but I thought I'd point it out.

    • @VintageHondaMinis
      @VintageHondaMinis  Рік тому

      OEM is oversized 14mm hex nut, this bike had a standard 13mm installed