ZPAP M85/M92 Peep Install Guide
Вставка
- Опубліковано 8 вер 2024
- Khyber Customs Dual Peep and V-Notch Peep compatible with the ZPAP M85/M92. Please visit our website for more details: khybercustoms....
Visit our sponsor Third Pin Threads at thirdpinthread...
The Crescent wrench was a nice touch. Looking to get one of these.
Installed mine today, fairly easy. Best upgrade you can do! I actually have a sight picture now. Helpful hint..once old sight out lay new one in to get a ideal where the holes will line up than set up pin and tap away. comes with extra pin and bb detent.
Sweet! Done and done,and thanks for the sticker.
To anyone wondering, a mid to late 2021 zpap92 had a standard pin that was peened on each side retaining the sight, not a roll pin. Lucked out and one side was peened poorly, so drove it out to that side and this video made it easy. Due to the size of the rear sight hood, the factory sight would flip under recoil. I test fit this with a slave pin and it seemed a little easily flipped, too, so put one of the ball bearing under and on top of spring. Being a tighter fitting roll pin, probably would’ve been ok, but I KNOW that sucker won’t move under recoil now.
Good suggestion here. Ball bearing, spring, ball bearing for a tighter detent engagement.
I have the one sided peened pin... So your saying to use a punch on the peened side? Or the other side to come out from the peened end? Im having trouble right now.and it's frustrating.
@@whatsgrowingon one side wasn’t peened enough. If only one side is peened well, drive it out TO the well-peened side. Otherwise it wouldn’t come out.
ETA: the tip of the punch will touch the poorly peened side. It will drive right out to the well peened side.
@@09cjonescj ya I've been hitting the side that is not peened to push out towards the side that is and it's still Jammed in there. Really tight . Then again I'm not using a good punch nor do I have it on a sturdy table so it wobbles a bit.
@@whatsgrowingon hahaha well brother get the correct size punch and stabilize the dang thing. It very likely won’t work without those two things 😂
Mine will be here Tuesday and I’m looking forward to it. Been creeping your website for a long time for them to come back in stock 👍.
When did they come back in? I was on their restock email list and somehow I missed it.
@@mcmutty680around 2 weeks ago
You explained it that easy, a caveman to do it. I dont have one, but I do have a aftermarket peep sight on my ras 47
Thanks, that went smoothly!
Just got my zpap92. Be talking to you soon! Good video👍
You should make a rear sight with windage and elevation quick adjust sight with high side to side of the front sight through rear visability.
Heck just one that does windage would sell like hotcakes!
Mine didn't install so clean either. Both pins bent. Was using both the plier method and the hammer and punch method. Grease on pins both times. Almost like the roll pin is too big. bent my punch in the process so had to drill pin out and damaged my khyber sight. Wasted $40 bucks.
Its way easier and less hassle to just not buy this product at all
Installing new pivot pin sucks !!!!!!!+
I wish I would have found this first. I fubared my sight. The roll pin got stuck in the blade. I was able to get it out of the sight leaves but not remove the pin from the blade. Even trying to drill it out was to no avail.
Just installed mine, simple enough, but that roll pin was a b**** to tap in. Hammers away. Loving the sight picture though.
The installation was significantly more difficult than the video. I've done this install multiple times and it gets easier but boy, between bending the pins and losing the ball bearings, its annoying. Love the sight picture.
got the sight installed easy enough, with only one ball bearing. the detent is so tight that a small punch is needed to depress the ball. to change positions. is this a common issue?
Same with my zastava zpap92 it’s very frustrating.
Yeah same here, I was using 1 ball bearing as the detent. One position is not quite tight enough, and one position requires a small punch to depress to get it to move. There is also some play in the whole sight, I wonder if the sight base holes are two different sizes. I may try with 2 ball bearings like someone said on another comment. I have a Zpap as well
@@drooknight5454 on mine I tried the 2 ball bearings which made it too tight. so I just stored a small punch in the grip. with a bore snake so it wont rattle around. bear in mind I have a friend with a zpap that has had none of these issues. so I am guessing it is an issue that only arises with certain production runs
@@blinkventure6497 Ok thanks for the reply. I noticed I could push the sight to one side (direction perpendicular to the barrel, pushed towards the safety) and it would flip that way, and this could be done by hand, maybe something you could try. Yeah I think you're right about the different production runs. I bought mine early 2021 I believe from a distributor. I may try to find a very slightly bigger ball bearing to prevent it from going as deep into the sight base hole and hope that helps. We'll see...
@@drooknight5454 happy to help, never thought of pushing to one side being a solution. Ill try that out
Does anyone know if the roll pins that come with the Khyber sights fit/work with the stock ZPAP sight? Just curious. Thanks!
This won't work for a zastava ZPAP92 alpha.. it has a peened pin so these punches will not work. It's frustrating.
Just found that out wish they would warn ppl about that.
@@painter4769 i know my master obi won. They must have sith tendencies.
We've got one on order and will check it out. This is the first I've heard of a change to the factory pivot pin.
@@khybercustoms did you guys figure it out just order one today 😅
Thats why the pin keeps rotating out. I've tried to JB weld it in but it's not a permanent solution.
I am hitting the pin pretty hard with the 1/16 punch. So far I've tore up the back of the punch but the pin hasn't moved. Does it only come out in one direction?
Make sure the firearm/topcover is secured in place with some kind of vise or gunsmithing puck. Pin should come out either direction.
@@khybercustoms I don't have a gunsmithing puck but everything is clamped down with several sturdy clamps.
how did you get that dust cover off
So I couldn’t get the pivot pin removed from my gun with the hammer and punch. Is there an additional step I missed?
Make sure the punch is lined up and the firearm is secured tight and not flopping around.
@@khybercustoms I did both of those, secured the gun using a bench vise and lined the punches up best I could used a small hammer then a larger one. Is it possible that they are peening both ends of the pivot pin to keep it from walking out?
@@RiflemanReveiws That has not been my experience, but the pivot pins are in there tight. No shame in seeking out a reputable gunsmith to help with installation of aftermarket parts. AKs are not as simple as ARs, they are built using very crude methods to loose tolerances. Some are tighter than others.
@@RiflemanReveiws I don’t know if you got your answer but mine is either not a roll pin, or is one with the ends peened, if it’s not then it’s a solid pin with the ends definitely peened. I’m going to try to center punch and the drill out the middle. I’ll let you know.
Any chance you can adapt that design to work for Arsenal pistols with the flip sight
The pivot/detent are totally different, and Kvar already sells a top cover with factory peep.
@@khybercustoms I’m sure for Kvar pricing too
@@Scott079 Still much cheaper than designing, prototyping, manufacturing, and producing one.
Can you swap that dust cover on to an m70?
No
I know whos ak that is lol. I see you clayco.
A bunch of our rifles have made appearances on the Klayco47 channel, including this M92 Underfolder.
Will this work on mpap?
These are for ZPAP M85/M92 Pistols
Will this work on my z pap m90 full size
No, its for M85/M92 hinged top covers
I highly recommend Not using the wrench it Will make this 10X harder I lost 2 ball bearings trying it this way. The sight won’t switch between the 2 different sight pictures easily no idea why redid this 2 times on the same side once on the other still nothing kinda bummed.