Watch This Before You Upgrade Your CVT Variator/Pulley.. ADV 150
Вставка
- Опубліковано 8 лют 2025
- theres many variator out there.. which one is the best??.. measure them before you install them on the bike.. no more guessing...
I ONLY gave dimension for ADV 150.. you need to calculate your own dimension to get the lowest possible ratio and highest possible ratio at the same time for your bike model
there is a way to calculate the required angle and dimension to get the best of both world..
ADV 150 riders can get the pulley with my dimension by letting Kenzo know " Malex ADV 13.8 ".
Kenzo matic facebook:
/ happy.handoyo
Do like, share and subscribe if you like to see more of my videos.. im thinking of doing " Full CVT Tuning Tips" with every single part explained in detailed what it does and how it affects the bike performance.
Music : Fwends by Reed Mathis
Hi Sky. you are right, on bigger primary pulley for upgrade. let me share current cvt. before buying matic, i heard about dragging. now, after over a year with beat esp and adv, the dragging issue is more prevalence on bigger cc but with same (simple) cvt set up. as more and more dyno service are available, put my adv on the mill. on hp/rpm chart, dragging showed as camelback graph line. the clutch bell wasnt round after hot runs. kevlar carbon clutch line, or zoomer clutch springs couldnt react the 1 mm or less discrepency at 5000 to limit rpm (limiter was not shift due engine began to stutter). factory reinforced clutch bell with thick plate but could cope with buildin heat after hard run. safe drive...
Peak power is at 8.4k rpm for adv.. as long as you tune your cvt to shift around 8k-8.5krpm you will see a flat line on the dyno...
In your custom setup from kenzo matic, did you also extend the roller path by making the end softer?
Hey bro, it's me, Takehow, Guang's fren, lastime TDM got f/I issue, went to ur school workplace & check. Very 👍🏼👍🏼💪🏼& interesting video u have!
Riding PCx now, mayb need ur help/link to get Kenzo matic stuff. 😅😅
What is the angle of kenzo pulley?
can your setting also be use if with pillion of 70kg? Total of 150kg. Also, your clutch bell bought from thailand is what brand?
my body weight is 50+kg. im using kenzo 13.8 pulley, kenzo clutch bell and the rest are stock. what roller weight do you recommend?
Udh pernah coba uma dan tdr blomm ?? Katanya lebih lebar diameter nya dan akankah lebih enak ??
What is the best angle 13.5 or any angle better than 13.5
13.8
Bro, do you recommend 13.7 degree pulley?
Depends on how high you want your rpm to be at low speed.. comfort and power is 14 degree.. 13.5 is like max pick up and very draggy low speed ride.. do take note that the angle will affect the roller weights you use..
@@mlxnrzhr thanks, for a 13.7 angle can you recommend the 12 grams? or 10grams? does higher constant RPM will give you more top speed?
No, you need to keep the rpm in the peak power rpm.. if your are running adv 150 standard, its 8.5 krpm.. top speed will also depends on your tallest cvt ratio..
@@mlxnrzhr bro jus tested a 14grams flyball, ive reach 8000rpm. but my speed is still 107kph. should i lower the flyball weights? im using 13.7 degree pulley modified ramp.
@@mlxnrzhr bro, Ive bought kenzos pulley just like yours, Im 60 kilos guy, I try to put 14grams dr. Pulley but for a 1.5km run, my top speed is around 108kph. what could be the cause? do i need to add more weight on the flyball/roller?
I own shortly a ADV 150, want get a better acceleration. Increase your recommend pulley this. Is the 12 g rollers the stock weight. I’m a 100 kg driver and hills around me here in Phuket/Thailand.
Stock weight is 20g.. you will need 12g with the 13.8 pulley..
Best is to get dr pulley sliders.. they last very long..
Clutch bell 690 g also useful?
@@hms1314 the 690g clutch bell from yuminashi are terrible. You can consider getting this type of bell.
cf.shopee.sg/file/d4f229f7c795a83ca4eba0365b9e923d
The most important part is the holes on the bell where the pads touch. They help dissipate heat..
cf.shopee.sg/file/4d2e04d9c0b21b15b9adcce67a59caf5
Many thanks, I try to get this clutch. Pulley ordered already 👍
When changing variators, do you need to change your clutch springs and contra springs, that is, do you need to change them to stiffer ones?
No. Stock spring still the best.
For 13.8 degree pulley stock springs are still the best?
Yes
What is your average gas consumption with your setup now?
43km/l... i dont go easy on the throttle.
@@mlxnrzhr ok. What is your average speed when you have that gas consumption? Mine is 70-100kph speed on 44.6km/L
Same as yours
Do you recommend the Kenzo Matic Bell for Adv? I just purchased kenzo matic pulley and drive face.
Bell yes, get those nmax shoe while youre at it..
Hey sir, it turns out my purchase of kenzo matic got cancelled. So I just purchase a 13.5 pulley and drive face. What cvt set can you recommend with this degree?
Next video clutch please haha 😛
Does Putting bigger Variator pushes my Throttle response and speed high. Or just another factory settings?
Theres 4 things that will affect your throttle response..
1)Variator face angle
2)Rear pulley helix angle
3)Roller weights
4)Contra spring
Top speed is all about engine peak power rpm..
Hi, I would like to ask if I could change my pulley even during break in period?
Just stick with stock during breaking in.. anything happens, the shop got nothing to blame..
What was your speed after testing your new pulley?
On a bad run 123, on a good run 127.. this pulley sets your peak power around 120km/hr.. power is actually dropping after 120..
@@mlxnrzhr ano full set up mo sir sa cvt mo ?
What's your set up sir? And what is your recommendation on my adv rollers, my weight is 85kg
So what roller weights were used?
Im using 12g.. really depends on your pulley angle.. aggressive angle will make your roller feels heavy...
How many degrees the size of your ratio??
You mean the drive face angle?
Berat rollernya? Atau sudut pulleynya?
@@mlxnrzhr the pulley
13.8
im currently using rs8 pulley set. and i lost the start acceleration. im thinking to change to race99 pulley set. any tips??? the first acceleration will be back???
Rs8 pulley angle seems aggressive with no top end.. aggressive pulley angle makes the flyball heavy.. you need to go lighter flyball.. i havent check out Race99 pulley..
@@mlxnrzhr thanks
@@mlxnrzhr i use 15grams im really loving it because i had acceleration in the middle. but its very frustrating when yung start throttling half in the beginning
I suggest you install rpm meter or install obd2 bluetooth reader... the obd2 reader like mine can datalog on the phone... send the datalogged file to me so i can tell you exactly what is the problem..
Without rpm reading i cant really tell if your spring is too hard or your rollers is too heavy... im still in the process of making CVT full tuning guide video..
Is it okay to use 13.8 degree pulley with a stock fylball for adv? And the rest all stock too.
No, the stock weight on 13.8 will feel 3-4gram heavier..
@@mlxnrzhr may I know your body weight? . My wt. is 81kg. Is it okay to use 12g flyball?
Yes 12g is good with your weight on the 13.8.. im 70kg..
@@mlxnrzhr whats the difference with other 12g flyball brands to the dr. Pulley?
Dr pulley can last a long time..
Love from Bangladesh. Here ADV just started to import from Indonesia so mechanics dont understand anything. Can you make a video on it please?
Will work on it
did you change the clutch canvas?
Nope
@@mlxnrzhr can you tell me the right cvt settings for adv 150?
Hey man, was wondering if i could DM you on obtaining some of these items for malaysia, please? I'm sick of dealing with the lazy ass sellers here who cant even give me basic info on what they're selling. Was thinking perhaps i could get a friend in Jakarta to help me source these items and ship them to me.
Im facing the same issue here, the local seller doesnt have the basic knowledge. i message the indo seller directly for parts.. some are willing to ship directly to you.
@@mlxnrzhr unfortunately I still can't find any 690g clutch bells in Malaysia. I did find a 715g one. Do you think that'll make much of a difference?
Not much difference..
Any recommended setups for adv.
Im using 13.8 pulley, 12g dr pulley, 690gram clutch bell.. the rest all stock..
@@mlxnrzhr where to get the spares? U install yourself?
Pulley and rollers i got from indo.. clutch bell from thailand..
Yes i install myself
Cvt is actually very easy to diy, maybe i should make a video on it..
Full cvt tuning po sirr
Coming soon
please for Indonesian translation?
akan membuat video dalam bahasa indonesia jika saya punya waktu
@@mlxnrzhr oke siap.. terus maju ya
ua-cam.com/video/V6ZhUFDnTek/v-deo.html
Sok ke Inggris an
hi, any tips on how safe is customizing stock pulleys? im planning to customize mine at a shop and tell them its its for daily use, but i have fears about customized pulleys breaking or causing other cvt issues.
Its very safe.. My pulley is customized from the stock pulley and ive done at least 25,000km of harsh riding.. i would usually try to max out the variator working range and tune the rollers weight for daily use..
@@mlxnrzhr thanks for the reply! it seems it will still be reliable so im definetly customizing mine