This is probably one of your top videos all time. Great job on all the work and explaining of everything. Super informative and easy to follow along. Now back to the Teg lol
Nice video. Just a tip, you can get an aftermarket cold air intake and on the rubber tube between the cold air intake and throttle body you can drill a hole in I'd say 3/8 get a PVC grommet and connect the iat to that without every having to cut any wires. The o2 sensor you can buy extensions on ebay.(get a 5 spd ex harness and you can bypass the iacv), you wont have to do the iacv mod but you will need to do the ckf bypass because the stock wire wont reach either. This is for everyone doing a swap that wants to avoid cutting wires, overall great video
It'll be like right off the show room floor. To get some extra power on your new motor and trans you should try the water meth hack. Just run the gas tank to empty and refill with the garden hose. You'll get at least 100 extra hp. Lol
Question, I have a 1996 Midori Hatch i just got with a B20B set in the bay that I have been piecing together to make work and finish. I have the 96 Harness in the car still and for the most part its plug and play as far as I can tell but what do I do with the CRANK plug? do I just tape it up and leave it unplugged as the B20B doesn't have a crank sensor on the oil pump. Also running an OBD1 distributor so i need to do the jumper harness you showed in this video as well as injectors. I have never done a honda swap so this is all new to me.
I love the videos but for the love of Pete it's idle air control valve (iacv) not air idle. idle air! I'm done with my stupid rant. keep up the good work. lol.
how was that rustoleum 2x spray paint? Ive heard mixed reviews on it but I plan on just using your method of spraying engine bays since my bay is scratched up to death.
I have a 97 dx ek hatch with a b18b1 p75 ecu I’m using a 2000 manual harness all the grounds are good and also relays and fuses are good but I’m not getting power to the ecu any recommendations thanks in advance
I have code 9 changed dizzy 3 changed wire harness and I got stock one watched this wiring install and I did it with a good stock one still code 9... 96 Civic 4 door DX with b20B HeLP
great video and it is helping me a lot! i swapped my 99 ek with b20 and just ran into this iacv plug problem and now i can get that taken care of.. swap came with no dizzy and i was told i can use d series dizzy... any info on d series dizzy on b series ?
I have a 97 civic ek. D18y8 I’m using a 97 civic dx computer with a b18b1 engine. I’m currently getting a iacv code, and a rpm fluctuation code, and a 02 sensor. Is there any info on this? I’m using a civic dx ecu also.
my d16z6 harness was a complete mess I pulled a wire out and it was not connected to any thing. I went a head and got a rywire for my crx like damn I over paid for the car problem after problem but I love my 1990 crx . ha Funny how the video came out at the same time I decided to do this
ya you definetly can use quick connects and butt connects like i do, but i would think its definetly worth noting that snce you have for almost everything else that you thinkthere is a better more correct way, is that its not as clean or correct as soldering it because soldering ensures a good connection the butt connects you cannot visualy see the connection its covered, pluss there ugly and and come apart and soldering is definetly in my opinion the better way of the two others you had mentioned
Very ironic. I just got a DB8 (GSR) with a b20b in a trade. The harness is so hacked, i dont know how it even runs. My question is, would it be an issue using an LS engine harness? I've seen a few GSR harnesses for $250-$350 and LS harnesses for $50-$80. i figure i can later add the vtec wires (when I decide on swapping the head) and save a good amount of money. Oh it's OB2
any possible way to use to stock ls integra harness? I bought a whole integra thinking is have everything but the civic si dohc mounts until I looked at the plugs on the driver side that go into the cabin. I got the 97 civic and 2000 integra ls with 99 ls ecu.
What do i have to change,build or modified to put a OBD0 B16A with a cable tranny in my 1996 Honda Integra with OBD2A wiring harness (What do i have to do so the obd0 engine fit in a obd2a chassis?) Any replied will very appreciated
crappy thing for me is i literally just did this in november but didnt know i could just switch plugs for the most part and took the whole fornt of the inside of my harness from my 91 manual accord lx to make that motor work in my 92 ex from a auto to manual couldnt get my temp guage to work so iinstalled onand the speedo doesnt work but i have a light for the speed senson so i hope thats all i have to fix for the speed to work but as for the temp guage i couldnt figure it out oh ya and the horns and fans i had to wire manually so i really need to consider a solution to fix up my wiring cause so far when something hasnt worked i just add more wires and directly wire it myself so for now i have fan, horn,and coolant temp gauge wiring going through my bay on top of all the original stuff so....
I'm about to do a k-swap and I got everything down besides the ECU and wiring harness..I have a 94 Honda Civic obd1 and a k24a2 is obd2..any suggestions for anyone would be helpful...fun fact I broke a breaker bar and a torque wrench trying to get the axle bolts out with heat on em🤣🤣🤣🤣🤣🤣🤣🤷♂️🤦♂️
Bro you need head up to chitown and throw down on my Honda lol I don't have time to work on it just have tons parts for it just sitting .. you know you're shit bro 👊😎
Man I got so many questions for you guys on my car, 2000 civic hatch b20b who ever did it didn't do a good job. Anyway I can get into contact with you guys?
Hey if I wanted to put in aftermarket engine mounts could I do it with just a jack and jack stands and if so where should I put he jack I'm barley beginning to work on my car and don't wanna mess anything up
I have 2000 CRV 4WD manual transmission with a b20 high compression motor swap and my OBD doesn’t seem to be connected also how do I know if it’s OBD2 or OBD1 please help
I got a question I have a 89 civic si hatchback with a 97 dx Y7 motor ok when I unplug my iacv my radiator cooling fan shuts of can the plug from the radiator housing be backward because I have a check engine light and my machine says it's the iacv
bro I have a swap equal to the beginning everything worked well but now that I handle it it has a failure as a cut but then when accelerating to high it works well without faults but in low acceleration it grabs a cut ....?
Hi guys..I have a 01 civic ex,5Speed manual.I had to get new engine..Ended up with good find..Found vtec engine with a little over 50,000 miles for 450$... Son's friend installed for free but didn't get to do wire harness..I have heard of jumper wire.Or maybe just show my friend this video!! Lol..I am going to check with junkyard first for ecm,heard that are very expensive new!!Sorry guys...Thank you in advance for any info comes my way!!☺️
HI MARK. I have civic 4door sir vtec. sunroof. it have d16y8 harness and computer. i swap it with b20b non vteck. its working but getting ideling. Rpm is going up, down, each 3 second. how i can fix the issue?
Please help, I have a 93 hatchback and a wanna mount a b16 motor , so I need to know witch hardness I can use for my b16 motor , also I need to know what post mount I can use,,,,,,, and also what engine mounts I can use ......please anybody help me , will appreciate it the help
@@HondaStreetGarage thanks bud.. could that also stop my gauges from working i can't tell speed rpm gas or coolant everything went out all at once. Thank you again 🍻
Hey how can I wire in the crank position sensor from a obd2 d16 harnes that is normally down low by the crank pulls too a pbd1 b18 that has it I'm the dizzy plz anyone help
You have choices go to school and learn how to repin the right way or buy jumper harnesses but always save your old connectors so you have options to go back I built an entire b20 harness for my eg but I wish I had money for the rywire harness for the looks knowledge can be a substitute for money in some circumstances but it’s up to you to make sure you do your research before you do that to a harness I destroyed one first then I nailed it the second time knowledge also cost money keep that in mind
hey where exactly do you live I live in Tampa Florida and I'm looking for a reputable Builder that can help me with my Acura Integra can you recommend anyone that you trust
Been out of the Honda game for a while and have bought a b20 swap ek for cheap. The wiring is a hack job. This video is so helpful!!
This is probably one of your top videos all time. Great job on all the work and explaining of everything. Super informative and easy to follow along. Now back to the Teg lol
eating cereal and watching your guy's stuff more than satisfies my mornings. thanks again!
Bro if im the one who own that car i gonna be happy on what you did on it. Keep up the good work.
Nice video. Just a tip, you can get an aftermarket cold air intake and on the rubber tube between the cold air intake and throttle body you can drill a hole in I'd say 3/8 get a PVC grommet and connect the iat to that without every having to cut any wires. The o2 sensor you can buy extensions on ebay.(get a 5 spd ex harness and you can bypass the iacv), you wont have to do the iacv mod but you will need to do the ckf bypass because the stock wire wont reach either. This is for everyone doing a swap that wants to avoid cutting wires, overall great video
Great vid. I'm doing b20b swap into my ek hatch. Using p75 obd1. Will definitely refer to your videos if i run into trouble!
What harness did you use for your b20b swap?
This is one of the best informative videos you've done man. keep it up
Just bought a B20b about to swap it into my ek hatch great video helps a lot !
4 cylinder I6 = Hedder, singular
V6-V8 = Hedders, plural
You always say "Hedders" other than that I find the content very entertaining
FZT Motorsport *header *headers lol
Timothy Cherrier Yeah... No!!! look it up playboy
he can't say it, and you can't spell it. haha
You know, me and my 11 year old son, enjoy hanging out at your shop. Thanks for teaching us :)
You guys do some awesome videos! Keep it up man👍
Nice work! Car Lot Special FTW...
Actually looks really good..👀👍™
You guys washed it without the distributor?
Edward yes to clean the inside of the motor. you just gotta leave the intake manifold open too. make sure to fill it with water. lol
popanollie1 ill make sure to do that to my trans too, i need a flush lol
It'll be like right off the show room floor. To get some extra power on your new motor and trans you should try the water meth hack. Just run the gas tank to empty and refill with the garden hose. You'll get at least 100 extra hp. Lol
popanollie1 you're telling me I can get another 100 HP just from my front lawn?? Boy oh boy im gunna be blowing fucking doors off!!
yes. lol. that made my day, i'm subbing to you too. lol
damn son watch the revs almost blew these iPhone 6 speakers cuh 😑 lmao
Saw the red hatch at cars and coffee this past weekend.
Been using solder wire connectors from Amazon. Only a heat gun needed.👌
Question, I have a 1996 Midori Hatch i just got with a B20B set in the bay that I have been piecing together to make work and finish. I have the 96 Harness in the car still and for the most part its plug and play as far as I can tell but what do I do with the CRANK plug? do I just tape it up and leave it unplugged as the B20B doesn't have a crank sensor on the oil pump. Also running an OBD1 distributor so i need to do the jumper harness you showed in this video as well as injectors. I have never done a honda swap so this is all new to me.
You can jump crank sensor wire to pick up signal from dizzy. You have to splice two wires at ecu plug.
I love the videos but for the love of Pete it's idle air control valve (iacv) not air idle. idle air! I'm done with my stupid rant. keep up the good work. lol.
how was that rustoleum 2x spray paint? Ive heard mixed reviews on it but I plan on just using your method of spraying engine bays since my bay is scratched up to death.
Oh man why spray paint the a/c connections 🤨 I love your content though it’s the best Honda channel by far
Yup..i agree...
I have a 97 dx ek hatch with a b18b1 p75 ecu I’m using a 2000 manual harness all the grounds are good and also relays and fuses are good but I’m not getting power to the ecu any recommendations thanks in advance
awesome job id be thrilled with the work if that was my car.
man you do some good work to that car.
Thank very much you help me a LOT .. mine is a h22a wish you can help in the ignition thank hope you see this
I have code 9 changed dizzy 3 changed wire harness and I got stock one watched this wiring install and I did it with a good stock one still code 9... 96 Civic 4 door DX with b20B HeLP
Sh8 way better job then some of these “shops” in south, FL for sure.
love the videos,nice job👍👍💪💪💪
great video and it is helping me a lot! i swapped my 99 ek with b20 and just ran into this iacv plug problem and now i can get that taken care of.. swap came with no dizzy and i was told i can use d series dizzy... any info on d series dizzy on b series ?
I have a 97 civic ek. D18y8 I’m using a 97 civic dx computer with a b18b1 engine. I’m currently getting a iacv code, and a rpm fluctuation code, and a 02 sensor. Is there any info on this? I’m using a civic dx ecu also.
my d16z6 harness was a complete mess I pulled a wire out and it was not connected to any thing. I went a head and got a rywire for my crx like damn I over paid for the car problem after problem but I love my 1990 crx . ha Funny how the video came out at the same time I decided to do this
Im changing my intake manifold & i need some kind of help with hose placement?
I think I connected my hoses wrong need a video on the hoses
All you need is one hose for the PCV , one hose for the brake booster , one small vacuum line for the FPR , the rest you can block off
perfect im throwing a y8 in my 97 dx coupe needed some help w wiring
Man how do you get them things to fire up?!!
My crx the seatbelt light stays on! Any ideas on where to start? I'm waiting for the electrical service book in the mail.
Hear some good grunge in the background. I thought I heard Alice in chains once?!
perfect info, can I use some of this going from obd0 to obd1 into my DA?
Awesome video! 👍
ya you definetly can use quick connects and butt connects like i do, but i would think its definetly worth noting that snce you have for almost everything else that you thinkthere is a better more correct way, is that its not as clean or correct as soldering it because soldering ensures a good connection the butt connects you cannot visualy see the connection its covered, pluss there ugly and and come apart and soldering is definetly in my opinion the better way of the two others you had mentioned
"dawn" dish soap is the best and cheapest for grease (or just dish soap in general) they even advertise it for cleaning oil
With the baby duck lol
Hey mate.. can you make some videos on how to delete the evap system.. what happen if we do so?
Can you do a video how to chipping the ecu to get rid of the o2 sensor cel, please. And how bad if we dont have a o2 sensor works.
Very ironic. I just got a DB8 (GSR) with a b20b in a trade.
The harness is so hacked, i dont know how it even runs.
My question is, would it be an issue using an LS engine harness? I've seen a few GSR harnesses for $250-$350 and LS harnesses for $50-$80.
i figure i can later add the vtec wires (when I decide on swapping the head) and save a good amount of money.
Oh it's OB2
any possible way to use to stock ls integra harness? I bought a whole integra thinking is have everything but the civic si dohc mounts until I looked at the plugs on the driver side that go into the cabin. I got the 97 civic and 2000 integra ls with 99 ls ecu.
Maybe I missed it, but is there a reason why these plug wires are not soldered?
Dude the song you use I love it I comment all the time what is it 😂
Braxton Rosas which song?
Honda Street Garage at 1:45
What do i have to change,build or modified to put a OBD0 B16A with a cable tranny in my 1996 Honda Integra with OBD2A wiring harness
(What do i have to do so the obd0 engine fit in a obd2a chassis?) Any replied will very appreciated
crappy thing for me is i literally just did this in november but didnt know i could just switch plugs for the most part and took the whole fornt of the inside of my harness from my 91 manual accord lx to make that motor work in my 92 ex from a auto to manual couldnt get my temp guage to work so iinstalled onand the speedo doesnt work but i have a light for the speed senson so i hope thats all i have to fix for the speed to work but as for the temp guage i couldnt figure it out oh ya and the horns and fans i had to wire manually so i really need to consider a solution to fix up my wiring cause so far when something hasnt worked i just add more wires and directly wire it myself so for now i have fan, horn,and coolant temp gauge wiring going through my bay on top of all the original stuff so....
I'm about to do a k-swap and I got everything down besides the ECU and wiring harness..I have a 94 Honda Civic obd1 and a k24a2 is obd2..any suggestions for anyone would be helpful...fun fact I broke a breaker bar and a torque wrench trying to get the axle bolts out with heat on em🤣🤣🤣🤣🤣🤣🤣🤷♂️🤦♂️
great vids brother
When this hatch was bought did it have a B16 block with an ls head ?
Bro you need head up to chitown and throw down on my Honda lol I don't have time to work on it just have tons parts for it just sitting .. you know you're shit bro 👊😎
Man I got so many questions for you guys on my car, 2000 civic hatch b20b who ever did it didn't do a good job. Anyway I can get into contact with you guys?
no_go_alpha thanks for the tutorial! just need a b20 head for my b series
Hey if I wanted to put in aftermarket engine mounts could I do it with just a jack and jack stands and if so where should I put he jack I'm barley beginning to work on my car and don't wanna mess anything up
What impact tools do you use I'm lookin into buyin some
If I have a 89 crx with b20z2 what engine harness should I use??????
Jesus Zavala non vtec?? use obd1 ls harness from integra
xCalixn1t3xdawgx ok thanks yes is non vtec
an unhacked harness.
I have 2000 CRV 4WD manual transmission with a b20 high compression motor swap and my OBD doesn’t seem to be connected also how do I know if it’s OBD2 or OBD1 please help
I got a question I have a 89 civic si hatchback with a 97 dx Y7 motor ok when I unplug my iacv my radiator cooling fan shuts of can the plug from the radiator housing be backward because I have a check engine light and my machine says it's the iacv
It might be a stupid question but how do you connect the ckf?
love the colour combo. actualy its the same as mine too. silver engine and trans with a wrinkle black valve cover.
maybe its just a honda dick thing
I have a question as to timing belts can u use my stock b20b gates timing belt for my b20vtec conversion??
bro I have a swap equal to the beginning everything worked well but now that I handle it it has a failure as a cut but then when accelerating to high it works well without faults but in low acceleration it grabs a cut ....?
Hey dude i have a 00 civic ex with b20 and rpm jumps after 3200 to 5k and stay there the motors in like limp mode
U reuse the valve cover gasket and the exhaust gasket?
keep up good work more integra video's
Anyway I could PM you about a a Honda issue??
wow That's What A Dominican with a country accent sounds like
Hi guys..I have a 01 civic ex,5Speed manual.I had to get new engine..Ended up with good find..Found vtec engine with a little over 50,000 miles for 450$... Son's friend installed for free but didn't get to do wire harness..I have heard of jumper wire.Or maybe just show my friend this video!! Lol..I am going to check with junkyard first for ecm,heard that are very expensive new!!Sorry guys...Thank you in advance for any info comes my way!!☺️
i replaced my alternator on my stock ex 99 and now the battery light is dimly on. do you have any idea of what it could be ?
I got a 98ek ex and I’m doing a ls swap tha vtec plug I have to pin it out from tha ecu
HI MARK. I have civic 4door sir vtec. sunroof. it have d16y8 harness and computer. i swap it with b20b non vteck. its working but getting ideling. Rpm is going up, down, each 3 second. how i can fix the issue?
Hms Alkashri I would check your idle air control wiring
Please help me! What changes do I need to make to a d16y5 harness to swap a b18c1 engine into my hx.
I have a 2000 Honda Civic ex what all I need to do a b18 swap with a automatic tran
you rly clean engine with water ... and without dizzy ? :D lol
3 to 2 CKF sensor is there any other way rather than bypassing it
Good video men
Please help, I have a 93 hatchback and a wanna mount a b16 motor , so I need to know witch hardness I can use for my b16 motor , also I need to know what post mount I can use,,,,,,, and also what engine mounts I can use ......please anybody help me , will appreciate it the help
Bro so I have to use my ek stock harness in my b series motor?
I'm here relax!
B18 swapped ek
my alternator not charging
Bro my rpm and my speed odometer not working and my radiator fan and my v tech? What do you think?
how much to fly HSG out to Colorado to work on my eg?
6 HALO why do that when you have BoostedBoiz near you lol
Bro I got engine wiring harness y8 do you think is work on my b18c1?
Thanks
I can usea the scanner in the obd2 port with obd1 ecu?
I have an 88 honda crx 1.5l I want to make a swap with an H22 I want to know what I need to do this swap
very useful 👌
Hello is that a ls hardness?
Do I have it right that anything 01+ ain't cool civic wise?
thornygravy pretty much, few exceptions
I have a 04 EM2.. it's slow but damn sexy. I proudly have no 'tuner' mods on it because well.. it's a d17.
My dash lights in my 98ek suddenly went out and also my tail lights..... my break lights still work.. what could it be?
A fuse or ground.
@@HondaStreetGarage thanks bud.. could that also stop my gauges from working i can't tell speed rpm gas or coolant everything went out all at once. Thank you again 🍻
@@HondaStreetGarage thank you again its working I found quite a few fuses blown. Even the dash fuse too.. I put new ones in and now work.. 🍻👍🏽
And tha Iacv valve in tha 98ex I have to corect tha Pins on tha ecu too
Hello guys...
I want to know how do you modify wiring..
Can u help me.
Thanks you
Hey bro I need help wiring up a b20b in a 1992 integra gsr
What can wire harnesses you used
Hey how can I wire in the crank position sensor from a obd2 d16 harnes that is normally down low by the crank pulls too a pbd1 b18 that has it I'm the dizzy plz anyone help
You have choices go to school and learn how to repin the right way or buy jumper harnesses but always save your old connectors so you have options to go back I built an entire b20 harness for my eg but I wish I had money for the rywire harness for the looks knowledge can be a substitute for money in some circumstances but it’s up to you to make sure you do your research before you do that to a harness I destroyed one first then I nailed it the second time knowledge also cost money keep that in mind
hey where exactly do you live I live in Tampa Florida and I'm looking for a reputable Builder that can help me with my Acura Integra can you recommend anyone that you trust
BlackBirdFPV I'm about an hour and a half away what do you need help with?
Damn, that hatch is beat. Poor thing.
MONEY saver
I have a question do anybody knows this to straight wire the big plug on the right under the hood from obd1 to obd2 please help
Nice
I'm assuming it's cause the previous owner didn't maintain it properly