How To Make Cooling Plates + Increase Production & Make More $$ Soft Plastic Bait Making

Purchase- pineoutdoors.s...
My Info
Facebook - www.facebook.c...
Instagram - @pineoutdoorsok
Discount Codes For Soft Plastic Bait Making
Baitplastics.com promo code pineoutdoors5%off must be all lower case as shown
Pouryourownworms.com Mf Manufacturing pineoutdoors10 for 10% off
Fatguysfishing.com promo code PineOutdoors exactly as shown
Amazon Affiliate Links
For Cooling System
Male Straight 1/4 Inch Tube OD x 1/2 Inch NPT Thread Push to Connect Fittings - What you'll use to connect the 800 gph water pump to 1/4" hose - amzn.to/41Fc4e0
Water Pump - VIVOSUN 800GPH Submersible Pump - amzn.to/3SK5HSD
Tubing - amzn.to/3y3FYuZ
Tap & Drill -1/4" Carbon Steel NPT Pipe Tap and 7/16" - amzn.to/3KNKntq
1/4" OD Quick Connect Fittings - 10 Pack Push to Connect Tube Fitting, Air Tool Fittings Straight Push Quick Release Connectors Tube Quick Connect Fittings, Male Straight 1/4" Tube OD x 1/4" NPT Thread - amzn.to/3ZdUKeE
Caps - 1/4" NPT Plug Brass Pipe Fitting Countersunk Thread Internal Hex Head Style Male - amzn.to/3EOiDkL
Long drill bit - DWDDL8X1/4 1/4" x 8" High Speed Steel Extra Long Drill Bit, DWDDL Series - amzn.to/3ZbfN1f
Not The Vise I Used Irwin Makes Quality Though - IRWIN Drill Press Vise, 4.5” - amzn.to/3IJWSDW
What I use to de-gas my plastisol - BACOENG 5 Gallon Vacuum Chamber - amzn.to/3wGZigW
Amazon affiliate link for 12" pegboard hooks - amzn.to/3Z0l6jI

[@darinblackburn6023]

Great way to DIY those plates. Would be cool to see the air vice sometime. Sure a person could save a load of cash.

[@danielspotten8213]

I did a different style air vice and finished it last week. I did use larger air pistons than the one I was looking at premade. I did spend about half as much cash as it would have cost to buy it. I do love to tinker so that is fun, not work, for me.

[@damianoffthegrid]

Like to see that 👍

[@danielnies7144]

Thanks for sharing brother and a little bit as good a whole lot better I agree my mono too

[@The_Next_Cast]

Another great video as always! Thanks for sharing!

[@Arrigo_Outdoor_Adventures]

Nice thanks for sharing

[@ecfd16]

Yes to the air vise let’s gooooooo! Thanks

[@tatehay3381]

Sweet! I would like to see a air vise video

[@michaelcobb1141]

If you use a dowel rod centering kit. it will give you a guide to keep it straight and its self centering. Plus it clamps tight. Norther tool and Harbor freight has it.

[@ronniecrook6313]

How did you make your air vice. Would like to see a video on it

[@josephthaxton4768]

I would like for you to make a veido on a air vise. Thanks for all the great videos you make and GOD Bless.

[@danielspotten8213]

Also, interesting to see you use your crescent wrench to torque your hex bit. That is a new one for me.

[@mikekimball9853]

This was a great video, would really appreciate the air vice

[@damianoffthegrid]

Great info appreciate it 🇺🇸〰️🦅

[@danielspotten8213]

Good timing on the video. This is my project for next week. I ordered my plates online and they shipped yesterday. I do need to get a vice like you have. I did like how you step on it to hold it in place and drill with a hand drill. I was trying to figure out how I could do it with my table top drill press but it can only do 3" at a time. I will probably start my holes on the drill press hoping to keep them straighter than I can with a hand drill then finish like you did. Thanks.

[@derrickdutton3785]

lets do it