I spend 39 yrs in glass industry in Dubai ....we had glass cutter from mp India, Mr nooral he was uneducated, but never seen glass cutter like him, who can beat intermac waterjet machine whc can cut any shape or thikness, he use to say bhai sahab Mai glass kattata nahi khata hu,. Means i don't cut glass i eat glass, seen him cutting any thickness....any shape like child plays with scissors cut paper.....great born talent
Thank you, I was able to cut to size a thick mirror following your technique using the hammer. A bit unerbing but it worked!! Great simple way of cutting very thick glass with simple tools, down to earth. I really like that, just using your hands, even wearing sandals 😊 Some people get over killed with so much gear and tools. From all the videos I watched, this was the most helpful. Thsnk you
jugaad technology: Thank you for this video. I see now that it is important to develop a "feel" for how hard to tap. This technique allows people to cut glass with simple tools and a little patience and perseverance. Thanks again for sharing your high level ninja glass cutting knowledge. 😊
One of the things novices do when cutting glass is using too much pressure with the cutting tool. You know when you have done it right by the sound. It should be a light hiss and the score is a fine line , almost hard to see. Too much pressure and the sound is crunchy with score looking like a deep scratch. The deep scratch are tiny fractures running radially from the line and at best will result in a rough cut and at the worst not cutting at all or running everywhere but where you wanted the cut. Also make sure you have cleaned the glass first and the cutter is not nicked and/or dirty. My humble experience.
Been cutting glass for 42 years now and thicknesses up to 19mm by hand and only time I used a tapper was to start the scores of 10 and 12mm circles. Never on straight lines.
1. use more big table to cut 2.after the first hit by hammer you use that pen under the cuting line 3.push down the glass ......then the cuting line more smooth than this
When I was kid we used to to the same, but we made sure both ends were tapped fist, then we used to tap o the middle. That way we would guarantee the cut would be uniform end to end.
Just Use a brush to apply the oil on the glass before you cut it with the glass cutter and then place the sodden back part of the brush under the glass on the end of the cut and snap it pushing down.
@@johnbernardvillamarin452yes I cut really big sheets of thick glass (3/8”) like that at my shop! There are a few ways that work nicely and this is just one of them!
This is also a method of cutting thick glasses ....nothing wrong in it . All methods are almost same only diffrence is how you apply force after scratching the glass .👍👌
That would be risky when tapping a large piece which would fall because of its weight. A support would be needed on both sides of the glass, and a ball pen hammer would have been better because of the round head as it would give softer taps, thinner glass can just be snapped after one tap to run the line, Thank You
IF it was a large piece, but it wasn't. The fact that the guy's made his own hammer from re-bar says to me maybe he doesn't simply have access to a plethora of tools so he makes do (& well) with what he has.
That's amazing, I just scored a 1/4" piece of glass that won't break, I tried tapping it with the ball on the end of the cutter, I guess I need something heavier to tap it with?
I tried this method several times on a Shower Glass 3/8” but the Glass won’t break !!! Any advice ( I have 72” L that I have to cut it to 48” ). Thank you in advance!!!
I spend 39 yrs in glass industry in Dubai ....we had glass cutter from mp India, Mr nooral he was uneducated, but never seen glass cutter like him, who can beat intermac waterjet machine whc can cut any shape or thikness, he use to say bhai sahab Mai glass kattata nahi khata hu,. Means i don't cut glass i eat glass, seen him cutting any thickness....any shape like child plays with scissors cut paper.....great born talent
Hats off to Mr Nooral...
That's not the good way to cut thick glass.Im a glass cutter for 36 yrs .
Uneducated?
Really!
@@alfredosantiaguel5784 please teach me. I want to learn thick glass cutting Sir. Thanks in advance. 💐😇
No sirve
Thank you, I was able to cut to size a thick mirror following your technique using the hammer. A bit unerbing but it worked!!
Great simple way of cutting very thick glass with simple tools, down to earth. I really like that, just using your hands, even wearing sandals 😊
Some people get over killed with so much gear and tools.
From all the videos I watched, this was the most helpful.
Thsnk you
jugaad technology: Thank you for this video. I see now that it is important to develop a "feel" for how hard to tap. This technique allows people to cut glass with simple tools and a little patience and perseverance. Thanks again for sharing your high level ninja glass cutting knowledge. 😊
Jeez weez, I would not even attempt it. Thank you for your expertise, and for sharing it with us.
Great job!!😊
Thanks. Sounds like Planning and Patience are key.
I have no idea how I got here but this was so cool to watch, clearly a craftsman at work
Well done!
thanks much for your experience leaning something here for you sir_ as a glass man
Техникээ хуваалцсанд баярлалаа.
Your are a great crack, thanks so much.
One of the things novices do when cutting glass is using too much pressure with the cutting tool. You know when you have done it right by the sound. It should be a light hiss and the score is a fine line , almost hard to see. Too much pressure and the sound is crunchy with score looking like a deep scratch. The deep scratch are tiny fractures running radially from the line and at best will result in a rough cut and at the worst not cutting at all or running everywhere but where you wanted the cut. Also make sure you have cleaned the glass first and the cutter is not nicked and/or dirty. My humble experience.
Thank you for the information.
Nope. Too much time just learn from another experienced person
I like your cool hand-made hammer!
بہت خوبصورتی سے شہشہ کاٹ دیا
Excelente video
Hadir nyimak boss ku suksesselalu 👍👍👍
I always say. " you can't control glass but you can tame it." I love my occupation and it seems as if you do too.
Been cutting glass for 42 years now and thicknesses up to 19mm by hand and only time I used a tapper was to start the scores of 10 and 12mm circles.
Never on straight lines.
Que usabas entonces en línea recta?
On utilise une equerre et pas une baguette de bois et du petrole ainsi qu une boule a detonner des tutos par des bricoleurs du dimanche .@@OuyaYouyo
Lovely,👌👌👌👌🏹🎯
Brilliant. Thank you so much for sharing.
Thank you for sharing your technique. 🙏🏾
1. use more big table to cut 2.after the first hit by hammer you use that pen under the cuting line 3.push down the glass ......then the cuting line more smooth than this
Thank you for the demo!!
Cutting glass in sandals… this could turn into a whole different type of video.
awesome idea it so effective.
Amazing!!
Wow that awesome I'm amazed nice n cool jugaad thx for sharing. 😍🌷
Que marca e modelo de cortador vc usa nesse vídeo ?
Good job
That"s a nice clean cut, excellent.
What an incredible skill
I need to do this to a 10mm table top. How do I smooth the edge and make it look neat once the glass is cut ?? Thanks great video 👍🏻
By using belt sanding machine u can make the edges smooth.
When I was kid we used to to the same, but we made sure both ends were tapped fist, then we used to tap o the middle. That way we would guarantee the cut would be uniform end to end.
Thanks so much! Can I use any other type of oil before the cut?
I was trying to same glass in small pieces but failed. I will trying your technique. Thanks for sharing
Good work
Does your technique work for cutting tempered glass? Thank you for sharing your experience.
No, tempered glass cannot be cut without annealing it again.
you cant cut tempered it will brake
Mantap bos
Puedes usar un pincel o un vaso he introducir el toyo. asi se lubrica mejor.
holy crap cutting glass in sandals friggin crazy
thanks alot...
Learned something today 🙏
Glass cuting ke liye konsa oil use karna hai
Aap kerosene ya diesel use kar sakte ho
Beautiful
Wonderful. Like 👍.
Good job.....
Giive him a applause......
Gracias
could you cut both sides ?? would that be better ?
Cut at one side is better
Just Use a brush to apply the oil on the glass before you cut it with the glass cutter and then place the sodden back part of the brush under the glass on the end of the cut and snap it pushing down.
I see this technic of the masters ,in the bigest size's,,and it really amazing with sudden loud sound,,,👍☺️🤣🇵🇭it works..
@@johnbernardvillamarin452yes I cut really big sheets of thick glass (3/8”) like that at my shop! There are a few ways that work nicely and this is just one of them!
Excellent 👍
Thank you
ua-cam.com/video/D0epZC3rxfk/v-deo.html see my video of glass cutting
Nice ❤
I have a project I'm doing to replace my patio glass. I was curious what should I do to make a center circle cut for my umbrella?
next, teach me how to make hole on the glass. thanks 😊
Please check my other video for drilling hole in glass...
Thanks for the tip
*_Keren Sekali_*
Thankyou sir
This is also a method of cutting thick glasses ....nothing wrong in it . All methods are almost same only diffrence is how you apply force after scratching the glass .👍👌
Fine sir
That would be risky when tapping a large piece which would fall because of its weight. A support would be needed on both sides of the glass, and a ball pen hammer would have been better because of the round head as it would give softer taps, thinner glass can just be snapped after one tap to run the line, Thank You
Why watch a video if you already know everything?
@@christianscustoms6429 That's what we call a dumb question ! Jignesh Tailor's advises are important .
You just earned a dislike .
Turn it over.
IF it was a large piece, but it wasn't. The fact that the guy's made his own hammer from re-bar says to me maybe he doesn't simply have access to a plethora of tools so he makes do (& well) with what he has.
many technic learned from this glass cuttng shows
That's amazing, I just scored a 1/4" piece of glass that won't break, I tried tapping it with the ball on the end of the cutter, I guess I need something heavier to tap it with?
Sir apne kach per line khichte samay kon si liquid dala h batao
Kerosene oil
If you scratch both sides of the glass with cutter it will become very easy
I tried this method several times on a Shower Glass 3/8” but the Glass won’t break !!! Any advice ( I have 72” L that I have to cut it to 48” ).
Thank you in advance!!!
If it is tempered glass, it cannot be cut
عمليه معقدة قديمه . فيه ادوات اكثر فاعليه واقل تعب
Nice
Hi. Can I use sandpaper to smooth the edges?
It is better to use emery stone when u try to smooth edges manually.
Will teak oil work for cutting fluid?
Hallo etnha time kathna ma lagha ga to farha to banha gya karegarh
will this method work with curves?
Yes, but you have to be patient while tapping glass
Does that work with tempered glass?
No, this trick will not work
U cant cut tempered at home dude
@@shiyamaifrad8933 I found out the hard way.. lol
But can professionals/companies do it or is it just impossible to cut?
@@BlackFaceTrudeau it is not impossible cause u can get custom sizes from companies i guess they cut it with some heavy duty machines
Tempered glass CANNOT be cut. Glass companies cut holes, dog doors, handles etc BEFORE tempering. Do not attempt it as it will explode.
Semmaaa
Pa comme ça
Mashallah
Bhai itte der me customer chale gaye ho gye hm 😂😂😂😇
What is the glue (gum) are you use ,reply me
Its not glue it is kerosene oil, as I mentioned
@@jugaadtechnology449 thanks ,koheda tiyenne
유리 참 힘들게 절단하네요 요즘 어떤 세상인데 아직도 유리에 오일발라서 절단을 하는곳이 지금도 있네요 주소알려주면 오일칼 선물로 보내주겠습니다 이 나라는 장갑이 비싸서 안쓰나요?
thanks for your appreciation.
Berapa kilogram tekananya?
keran bos ku 🙏🙏 salam kenal bos
pueden ponerlo en el piso y colocar un clavo en la linea de corte y hacer presión en ambos lados con los pies.. y zuazzzzz
I never knew this
👍
How can I buy a cutting blaide, and average price.
Very good👍
De hamer is te breed, gebruik een puntige hamer
👍👍👍
How to cut a tampered glass???
Tempering is the final process for a glass .So it would not be possible to cut it.
Tempered glass is a different animal. Think of tempered as a bubble and you end up popping the bubble when you break the surface.
Thank you
Aurino
Awesome
Where to order?
itu minyak nya apa bang
Wow
Come here in tubod glass... We will show you how to cut 12mm thickness of glass.. That is so basic...
Good
Thank you bhai
I thought the end would be all smooth, but was wavy. Not what I'm looking for. Also, do you think it's wise to be wearing sandals when cutting glass?
Aap ye bhi likhe ki sirf glass wale expert hi ka te warna hath me lag sakta he bhai
Hadir
glass per miti lagaker cut kite hai yards kuchen aur?
No tiene ni idea como se corta un vidrio ese es un aprendis