2017 and newer V8 mopars come with a pretty solid exhaust system and better intake than that older car you used....it should be a better bolt-on mod for newer cars.
I've got one on my 2011 R/T with a mopar intake and a corsa extreme cat back. The car does bog a bit at low rpm, think it's creating too much airflow even with the mods. I have no tune on the car as well.
@@ullysesramirez9577 it runs fine and drives good, pulls good. If you're going to tune it I'd say go for it. They say it adds a little power but I haven't noticed much of a difference from stock on my car
Judging by everyone else’s comments, you’ll get more air, but may not a bit at lower rpm’s. Look into a pcm swap kit with Diablo, or any brand of you don’t want Diablo, but I haven’t found any other pcm swap kits, and then tune it
i just bought this i have a 2019 challenger scatpack but the factory throttle body bolts don’t fit the new one and didn’t even come with bolts, i don’t even know where to buy these bolts can someone help?
I have a 2015 5.7 Hemi it has magnaflow exhaust and Airaid cold air intake. I’m considering the 85 mm throttle body. Will this cause any issues with the car, bogging or stalling, or should I just keep it as is?
@@Chris00088 no but I’m still interested, Im worried, don’t want to sabotage the reliability of the car by messing with the throttle body set up, and smog inspection hassles.
@@Chris00088 I got a 2020 Charger scat with borla n K&N intake just bought this and made the car a lot quicker pulling in a lot more air intake temps are down 5-10 degrees
Yes the throttle body is bigger but manifold inlet is still the same and you will need more fuel if more air is put in engine so you will need to tune or it will be too lean might even throw a code. For the money you won't see big Hp jump. Sorry.
I'm going to install the Injen Evolution cold air intake when I install an 85MM throttle body. Will the connector hose from the intake to the throttle body fit the 85MM throttle body? Thx Dave
When driving normally a new throttle body will definitely give you slightly better gas mileage due to it being easier for your engine to draw in air. However, I wouldn't expect more than a 1 or 2 mpg increase. -Zach
So. If I do a cold air air filter set up and modify the exhaust? This 88 intake is a good upgrade? Or will it bog it down. I live in Cali. So I don’t want to put headers on it.
So I installed this on my 2020, and while everything runs good, when I start the car, I see a lightning bolt that goes away after starting but it still shows up. I tried to do throttle reset with on and off with the pedal, now a red light appears when I start along with lightning bolt. They both disappear but it bothers me. Help
We may be able to cut a little bit of a deal, but we don't have a specific discount for that haha we can't do too much about exchange rates. Give our customer service team a call at 1-877-887-1105 if you'd like. -Zach
FASTMAN uses a brand new TB directly from Chrysler. No way of telling by just looking when it's all bolted up. Factory TB that he ports. True Port all the way through.
I tried a 90 mm on my 6.4L Challenger and wasn't able to get the throttle pedal working. Re-installed the factory 80 mm - still dead in the water. Had to take the car to the Chrysler dealer to get the gas pedal working again.... 90 mm is too big... Now looking to use a 85 mm.
Check out the following link! BBK makes an 85mm and 90mm throttle body that will fit both 5.7L and 6.4l HEMIs! -Zach www.americanmuscle.com/bbk-85mm-throttle-body-0812-v8.html
What size was the original throttle body i have a v6 2013 im pretty sure mines is a bit smaller so I'm trying to put a 85mm throttle on myself will I need an adapter
This specific throttle body will not fit on a V6, but BBK does offer a 78mm one that does fit 11-19 3.6L that you can find at the following link. Thanks for watching! -Zach www.americanmuscle.com/bbk-78mm-throttle-body-1118-36l.html
Subscribe for Daily Challenger Videos: muscle.am/2TXrfwf
Shop This Throttle Body: muscle.am/2ChG3yJ
So you never had to disconnect the battery terminal or do a relearn?
Thank you man! You just saved me probably hundreds of dollars taking it in the shop! Iron sharpens iron.👌🏽👍🏽👍🏽
Thanks for watching, John! -Zach
i got a 2014 shaker, i cant wait to get a throttle body.
Thanks for watching! -Zach
Keep up the challenger content it’s great 👍
Thanks for watching! We really appreciate it! -Zach
Check out FASTMAN throttle body. Best in the game. True ported TB all the way through. Then let Jay Greene write you a tune.
2017 and newer V8 mopars come with a pretty solid exhaust system and better intake than that older car you used....it should be a better bolt-on mod for newer cars.
Check out FASTMAN throttle body. Best in the game. True ported TB all the way through. Then let Jay Greene write you a tune.
Will this throttle fit with my kn cold air Intake system?
I've got one on my 2011 R/T with a mopar intake and a corsa extreme cat back. The car does bog a bit at low rpm, think it's creating too much airflow even with the mods. I have no tune on the car as well.
vic_dsm does it still perform good? Thinking about buying one but all I have is a K&N cold air intake
@@ullysesramirez9577 it runs fine and drives good, pulls good. If you're going to tune it I'd say go for it. They say it adds a little power but I haven't noticed much of a difference from stock on my car
@@FPSItaliaA you may need a better tune bro
Definitely need a tune, tour mods are doing nothing
Will this fit a 3.6L pentastar? It shows on the website that it will but just making sure?
Do you need a tune after install
I have 2023 Durango RT Premium 5.7 and looking to see if this will do a performance gain as stock?
Will an 85 mm make a difference with my 2017 5.7 it’s got the mopar cold air intake and Borla Atak catback exhaust. Without a tune ?
Judging by everyone else’s comments, you’ll get more air, but may not a bit at lower rpm’s. Look into a pcm swap kit with Diablo, or any brand of you don’t want Diablo, but I haven’t found any other pcm swap kits, and then tune it
Bog a bit* sorry
i just bought this i have a 2019 challenger scatpack but the factory throttle body bolts don’t fit the new one and didn’t even come with bolts, i don’t even know where to buy these bolts can someone help?
What is that extension weird tube attachment to the intake tube bend? Because mine doesn't have that? Its above the alternator.
Why doesn't or do Edelbrock have a 92mm throttle body to go along with their intake manifold for the 5.7/ 6.4
I have a 2015 5.7 Hemi it has magnaflow exhaust and Airaid cold air intake. I’m considering the 85 mm throttle body. Will this cause any issues with the car, bogging or stalling, or should I just keep it as is?
Check out FASTMAN throttle body. Best in the game. True ported TB all the way through.
Did you ever buy it? Did you have any issues? I just bought one waiting for it to get here.
@@Chris00088 no but I’m still interested, Im worried, don’t want to sabotage the reliability of the car by messing with the throttle body set up, and smog inspection hassles.
@@tappan48 I’ll let you know how it goes once I get mine.
@@Chris00088 I got a 2020 Charger scat with borla n K&N intake just bought this and made the car a lot quicker pulling in a lot more air intake temps are down 5-10 degrees
Can I get this for a Dodge GT?
Yes the throttle body is bigger but manifold inlet is still the same and you will need more fuel if more air is put in engine so you will need to tune or it will be too lean might even throw a code. For the money you won't see big Hp jump. Sorry.
He said that in the first 45 seconds.
So will this work with my 2016 5.7 challenger. HC airbox and bbk shorty headers and hurst 3” cat back exhaust no turne thanks
I'm going to install the Injen Evolution cold air intake when I install an 85MM throttle body. Will the connector hose from the intake to the throttle body fit the 85MM throttle body? Thx Dave
I’m looking at the 90 mm throttle body for my 2021 charger rt do all the same rules apply ? In the website it says it fits just making sure
That was easy 👍👍would they have them for a 2021 ?
This kit actually does fit 2021 models! Check out the following link! -Zach
muscle.am/2ChG3yJ
Will a 87mm throttle body upgrade & a cold air intake hurt my 2018 Dodge Charger rt ?
Check out FASTMAN throttle body. 84mm with Jay Greene tune.
He says you don’t need a tune but you def need one or it runs rough on low rpm
That part
What about the 2019 Scat Packs? Their exhaust and intake are pretty solid from factory, would this be a good mod to start with?
Embidd No
Check out FASTMAN throttle body. Best in the game. True ported TB all the way through. Then let Jay Greene tune it. It will be power you can feel.
Could this fit a 2014 dodge challenger sxt
Besides the throttle response, DOES IT GIVE YOU BETTER GAS MILEAGE?
When driving normally a new throttle body will definitely give you slightly better gas mileage due to it being easier for your engine to draw in air. However, I wouldn't expect more than a 1 or 2 mpg increase. -Zach
Is a body throttle spacer required separately?
So. If I do a cold air air filter set up and modify the exhaust? This 88 intake is a good upgrade? Or will it bog it down. I live in Cali. So I don’t want to put headers on it.
Wont do anything; stock components outflow the engine
I added a Volant cold air intake with straight exhaust in the rear should I be looking into a 85 mm throttle body?
Check out FASTMAN throttle body. Best in the game. True ported TB all the way through. Then let Jay Greene write you a tune.
So I installed this on my 2020, and while everything runs good, when I start the car, I see a lightning bolt that goes away after starting but it still shows up. I tried to do throttle reset with on and off with the pedal, now a red light appears when I start along with lightning bolt. They both disappear but it bothers me. Help
Take it to a mechanic and or go to advanced and check codes.. even if it goes off they can or you can read it..
You didn’t disconnect the battery? First.
Probably just did a throttle body relearn procedure.
Will these work on my 2010 ram r/t
Do you offer a discount to Canadian customers who had a 34% exchange rate 😝
We may be able to cut a little bit of a deal, but we don't have a specific discount for that haha we can't do too much about exchange rates. Give our customer service team a call at 1-877-887-1105 if you'd like. -Zach
Is it ok for Chargers
Do you need to disconnect the battery to install?
Yes
Does changing your throttle body have an affect on your warranty for your challanger
FASTMAN uses a brand new TB directly from Chrysler. No way of telling by just looking when it's all bolted up. Factory TB that he ports. True Port all the way through.
No because it doesnt interfere with the engine itself
I’ve got a shaker is there a specific one I need to buy ?
Nope it will work with a shaker I have 2015 shaker my self.
Check out FASTMAN throttle body. Best in the game. True ported TB all the way through.
Would it do more harm then help to install the 90mm instead
I tried a 90 mm on my 6.4L Challenger and wasn't able to get the throttle pedal working. Re-installed the factory 80 mm - still dead in the water. Had to take the car to the Chrysler dealer to get the gas pedal working again.... 90 mm is too big... Now looking to use a 85 mm.
Check out FASTMAN throttle body. Best in the game. True ported TB all the way through. Then let Jay Greene write you a tune.
I got a 2015 scat pack. With mopar cold air intake, and mid muffler delete. Will the 85mm work better for me than the factory one. ?
This 85mm throttle body will definitely help open up your airflow more than factory! -Zach
@@AmericanMuscleDodge do you have to charge out any hoses. Or will it bolt direct without any adapters or tubing change.
Check out FASTMAN throttle body. Best in the game. True ported TB all the way through. Then let Jay Greene write you a tune.
What do the 4 throttle body bolts get torqued to ?
I've read so many answers on this. I asked Jay Greene and it's best to go by feel. He said he's seen them strip even at factory spec. at 108 in-lbs.
Will this TB work on a 2020 scatpack?
Go with FASTMAN throttle body. Oversized 84mm with a Jay Greene tune.
@@davidsmith4186 I been seeing a lot of ppl say Jay Greene tune but my local tuner uses HP 🤔
Got anything for a 2011 challenger 6.4
Check out the following link! BBK makes an 85mm and 90mm throttle body that will fit both 5.7L and 6.4l HEMIs! -Zach
www.americanmuscle.com/bbk-85mm-throttle-body-0812-v8.html
Check out FASTMAN throttle body. Best in the game. True ported TB all the way through. Then let Jay Greene write you a tune.
Does this work with a SRT8 6.4 2012?
This will not work with that 2012 6.4L unfortunately. -Zach
Check out FASTMAN throttle body. Best in the game and a TRUE ported TB.
@@AmericanMuscleDodge Bbk claims is fits for 2012 except CA for certain emissions. Do you know this doesn’t fit ?
Why does this not fit a 2009 Challenger R/T?
Check out FASTMAN throttle body. Best in the game. True ported TB all the way through. Then let Jay Greene write you a tune.
45 minutes to do this?!
Give or take! -Zach
...as he puts it on a vehicle with a stock non-cai intake.
exactly what i was thinking
This was for demonstration purposes. There was no need to slap a CAI on it.
ryathoma Donaldson Power core filters in corsa closed box cia does more than just create nice deep sound.
Why cant all mods be this easy? 😅
Wish they could be for everyones sake. 😅 Thanks for watching! -Zach
What size was the original throttle body i have a v6 2013 im pretty sure mines is a bit smaller so I'm trying to put a 85mm throttle on myself will I need an adapter
Check out FASTMAN throttle body. Best in the game. True ported TB all the way through. Then let Jay Greene write you a tune.
Does any of this cause the check engine light to come on?
Nope! If installed properly, you won't have any issues with check engine lights. -Zach
But can you put it on a V6? All us minions need to know
This specific throttle body will not fit on a V6, but BBK does offer a 78mm one that does fit 11-19 3.6L that you can find at the following link. Thanks for watching! -Zach
www.americanmuscle.com/bbk-78mm-throttle-body-1118-36l.html
You can, bit it's like 8 grand and comes with a Hemi.
You need to buy the two extra cylinder expansion kit to make it fit
Bad reviews on this on amazon
Check out FASTMAN throttle body. Best in the game. True ported TB all the way through. Then let Jay Greene write you a tune.
Do you need to disconnect the battery first?
I would highly recommend disconnecting the battery, yes. -Zach