2:33 is salvagable. clean it the best you can and look for the D point, and check if its shorted to gnd. Flood it with uv mask, cure it, and slowly scrape to the d point. Check if the short is gone. If not, redo the process again.
hey, do you do international orders or just US? ive been trying to install a modchip for weeks on my switch lite, i accidentally bridged the two sides of the cap on the right of the cpu, i think i can remove it with solder wick but after practising for a bit on other electronics im having trouble getting it to reliably remove the solder
Hello brother Is it possible to help me with the same problem? I do not have a resistor of this size I have a slightly larger resistor 0401 How did you install it Thank you
I hope you can tell me what appropriate resistor you put, I have a purple screen and I can't with a 4.7k one. above they get in diode mode with red probe to ground, 290, under the pad where point A is soldered (CMD) they get the value of this video. What's wrong with it that gives me 290 and not 302? What can it be? Can you help me?
Hello, very good, what resistance is placed at point A (CMD)? I mean the impedance value, is it a 4.7k or a 10k? Spero possiate dirmi che resistore adeguato avete messo, io ho schermo viola e non riesco con uno da 4.7k. sopra ottengono in modalità diodo com sonda rossa a terra, 290, sotto il pad dove si salda il punto A (CMD) ottengono il valore di questo video. Cosa c'è che non va sopra che mi da 290 e non 302? Cosa può essere? Potete aiutarmi?
I faced this nightmare of purple screen of death and get rid of it by removing the picofly ship clean everything and put some solder on A point on where this capacitor is located by miracle the switch works again and i ressamble everything back to normal state and giving back to customer ..''what a nightmare .
I love watching people repair stuff, but your iron needs cleaning and the flux you’re using is horrible, other then that I don’t mind watching your content
Purple screen almost always means theres a problem with that 4.7k ohm cmd resistor. Nice repair 👍
Absolutely right. Thank you for the input.
That was it for me too. Resistor looked fine. No missing pads. Replaced with 4.7 ohm resistor and switch is back to life. Thanks!!!
@@brianone23Hi, do you mean a 4.7 kohm or 4.7 ohm one?
Have same issue with my switch lite..where this resistor located on switch lite?..thanks
2:33 is salvagable.
clean it the best you can and look for the D point, and check if its shorted to gnd.
Flood it with uv mask, cure it, and slowly scrape to the d point. Check if the short is gone. If not, redo the process again.
Much appreciated. I’ll look into it.
I think I read somewhere that the capacitors from a RP 2040 chip fit to the Switch Nvidea chip
hey, do you do international orders or just US? ive been trying to install a modchip for weeks on my switch lite, i accidentally bridged the two sides of the cap on the right of the cpu, i think i can remove it with solder wick but after practising for a bit on other electronics im having trouble getting it to reliably remove the solder
Only us at the moment my friend. Thank you for your inquiry and your support.
Thank you for the video, I had the same problem, I put a 4.8k resistor a little bigger, but it works fine, the switch came back to life👍
Glad it helped. Stay tuned for more vids.
Hello brother
Is it possible to help me with the same problem? I do not have a resistor of this size
I have a slightly larger resistor 0401
How did you install it
Thank you
That resistor is tiny, were you able to solder that by hand or did you end up using hot air?
I used the solder iron. No need for heat gun.
I hope you can tell me what appropriate resistor you put, I have a purple screen and I can't with a 4.7k one. above they get in diode mode with red probe to ground, 290, under the pad where point A is soldered (CMD) they get the value of this video. What's wrong with it that gives me 290 and not 302? What can it be? Can you help me?
I have error blue and yellow then yellow light - how fix it please - version fw_2.73.uf2
Hello, very good, what resistance is placed at point A (CMD)? I mean the impedance value, is it a 4.7k or a 10k? Spero possiate dirmi che resistore adeguato avete messo, io ho schermo viola e non riesco con uno da 4.7k. sopra ottengono in modalità diodo com sonda rossa a terra, 290, sotto il pad dove si salda il punto A (CMD) ottengono il valore di questo video. Cosa c'è che non va sopra che mi da 290 e non 302? Cosa può essere? Potete aiutarmi?
Nice job. But you should use a smaller solder tip
I appreciate the input.
isopropyl alcohol?
Thank you.
My switch lite has a purple screen after installing RP2040, any idea what could be the problem?
Resistor on point A
@@Wayayeo Thank you, I appreciate your help.
mine is a switch lite backlight is not workimg after the mod. what could have gonne wrong
Check your fpc connector pins.
I faced this nightmare of purple screen of death and get rid of it by removing the picofly ship clean everything and put some solder on A point on where this capacitor is located by miracle the switch works again and i ressamble everything back to normal state and giving back to customer ..''what a nightmare .
I too found a bad chip can cause this issue. Replaced chip and no more purple screen.
I love this videos, restore a Nintendo is relaxing
Glad you enjoy it!
You could save so much time and hassle by just cleaning things with isopropyl alcohol instead of using whatever scraping tool you are using.
Appreciate the input.
I love watching people repair stuff, but your iron needs cleaning and the flux you’re using is horrible, other then that I don’t mind watching your content
Thank you for the input.