Shes a bit sluggish off the line but I hear the motor RPM only is nearly the same throughout the entire pass along with a large amount of tire smoke. That tells me you're applying too much initial start power. Maybe try a lower punch setting in the ESC adjust your transmitters throttle speed or start power point setting. If the tire is slipping enough to have visible smoke in the daylight you can't get maximum traction
My buddy & I did a beautiful pass 132ft @ 1.330 Arrma 1/7scale That information we will not share ! We race to win cash & prizes it’s all in the fun& games but the competition is real! We respect the hard work we put in thousands of dollars to finally build super cars 132ft drag racers
This is the reason why the hobby i united states 🇺🇸 is falling off . Because of people like u @fabbo60 .that want to keep secrets 😂. Its all in fun who hold secrets with toy cars . Great video @uae rc addicts i share all the information. A bro im a tell u what to run bro go get a 4000 cordova motor bro gear it 2 the 1 and u can get to 1.3 go up on your kv on that car and u will run 1.3 . U welcome 🙏🏾bro . Im watching u guys , having fun thats the beauty not holding secrets.
I have always wondered why do larger scale rc cars stick to the 132 ft drag racing measurement. This is for 1/10 size cars and is a true scale representation of a real qtr mile drag strip. Technically, a 1/7 car should run around 188 ft to make it a true representation. In the end, I guess it really doesn't matter as its all about having fun. Great car BTW!!!
I work hard at this sport with trial & error it’s expensive & time consuming…. That’s too much information Good looking build keep up the good work but keep the secrets
Those info should not be secrets in my opinion because newbies are having very hard time and loosing money on wrong setups some one should put them in the right direction also i didn’t share the 1.6 sec setup at least i am trying to help and growing the hobby
Is the 1.6 setup different gearing or remote tune.. without giving exact info can u point is in the rite direction to lower times? Higher or lower on gears ? 1/2/3 stage on remote to get. It? That will be very appreciated without exact info.. keep up the good work!💨💨🚀
@@dwightclemons9921 I use a Futaba 10px so most of my adjustments are all in the “tune” if u hit 1.7 then u prolly have the correct gearing to do a 1.6 or a 1.5 … Best advice I can give is keep trying & a 1 stage can be just as affective as a 3 stage. Depending on your surface but most people put too much power & think more power is faster but it’s NOT
The happiness is all we are looking for! Great info video. It was much needed!
Thanks for the sweet words
Shes a bit sluggish off the line but I hear the motor RPM only is nearly the same throughout the entire pass along with a large amount of tire smoke. That tells me you're applying too much initial start power. Maybe try a lower punch setting in the ESC adjust your transmitters throttle speed or start power point setting. If the tire is slipping enough to have visible smoke in the daylight you can't get maximum traction
My buddy & I did a beautiful pass 132ft @ 1.330
Arrma 1/7scale
That information we will not share ! We race to win cash & prizes it’s all in the fun& games but the competition is real!
We respect the hard work we put in thousands of dollars to finally build super cars 132ft drag racers
Exactly
This is the reason why the hobby i united states 🇺🇸 is falling off . Because of people like u @fabbo60 .that want to keep secrets 😂. Its all in fun who hold secrets with toy cars . Great video @uae rc addicts i share all the information. A bro im a tell u what to run bro go get a 4000 cordova motor bro gear it 2 the 1 and u can get to 1.3 go up on your kv on that car and u will run 1.3 . U welcome 🙏🏾bro . Im watching u guys , having fun thats the beauty not holding secrets.
Adrenaline and happiness!!! Love it! thanks for all the good tips on setup.
Most welcome
Great video appreciate the run down thank you.🙏
My pleasure!!
@@UAERCADDICTS 🙏
Nice car and great info as always!!
What A Beast. 😈💪🏼Awesome Build Brother...✅️🔥💥🥇🏆... Alhumdulliallah..🙏
Great video mi friend
Thank you 👍
Great Video and Information Brotha!! And thanks for always answering my questions!!
💪🏾Thanks for making this video and building a beast
It's amazing my friend .
great info. been wondering how i can improve suspension for drag.
do you have the rear lower than front?
No the front should be lower always
We always put the thicker tire in the rear it will make the nose down without adjusting factory settings
@@UAERCADDICTS thanks. I weren't sure when you said "-1 on rear". 1/7 drag is not very popular here in UK so learning from what I see 🙏
Make the rear higher than front bu 0.5 cm
Would this setup work on the felony almost the same car
Yes but unite rear and front diffs
I wanted to get a Tp motor 1700kv and run the same castle to bash and drag lmk what you think
Raise up the kv a little bit above 2000
But won’t I have heat issues I was thinking 2200kv 8s one I’ll runn huge fans on it but just wondering
I have always wondered why do larger scale rc cars stick to the 132 ft drag racing measurement. This is for 1/10 size cars and is a true scale representation of a real qtr mile drag strip. Technically, a 1/7 car should run around 188 ft to make it a true representation. In the end, I guess it really doesn't matter as its all about having fun. Great car BTW!!!
We know that but it is fear enough if you will do the acceleration science
Thanks for the info!
What gears do u recommend for kill mode 2900kv?
This is a 6s motor only it will over heat on 8s
Hi bro, what if FSR using mmx8s TP4060 2000kv. Any suggestion for gearing, diff, tire, suspension etc?
Your kv is too low for 132 ft
But i can help somehow on your fsr stock spur use 24 pinion. On 8s
@@UAERCADDICTS im using 43spool 22pinion is it good?
@@UAERCADDICTS and what the best setup on mmx8s like
Punch level
Power
Etc
@kelvinchia4750 to be honest i love them on default and do some adjustments from remote only
جزاك الله خير بس انا حطيت ورى ١٢٥ الف و دفريشن امامي ١٠٠ الف
ليش تنصح فقط ١٠ ؟
عشان ما يشاوح عزيزي
@@UAERCADDICTS اشكرك عالمعلومة.. هل للسرعات العالية اللي انا سويته صح ولا غلط ؟
اذا توب سبيد عادي لو ثقلت الاويل
how you line the rear tires?
0 camber
How much should the mph be when gearing
125
what do u mean by - 1 droop at the rear
I mean to tight the droop screw more in front and minus one in the rear this will make car nose down more
Good build.
very nice!
Thanks!
Thanks brother 🙏🏾
very good very nice!
I work hard at this sport with trial & error it’s expensive & time consuming….
That’s too much information
Good looking build keep up the good work but keep the secrets
Thanks and most welcome
Those info should not be secrets in my opinion because newbies are having very hard time and loosing money on wrong setups some one should put them in the right direction also i didn’t share the 1.6 sec setup at least i am trying to help and growing the hobby
@fabb60 As if any of us will be racing each other lol relax he's helping a lot of people out. It's not that serious bro.
Is the 1.6 setup different gearing or remote tune.. without giving exact info can u point is in the rite direction to lower times? Higher or lower on gears ? 1/2/3 stage on remote to get. It? That will be very appreciated without exact info.. keep up the good work!💨💨🚀
@@dwightclemons9921 I use a Futaba 10px so most of my adjustments are all in the “tune” if u hit 1.7 then u prolly have the correct gearing to do a 1.6 or a 1.5 …
Best advice I can give is keep trying & a 1 stage can be just as affective as a 3 stage.
Depending on your surface but most people put too much power & think more power is faster but it’s NOT
What is ur times with this setup
8s prep 1.7
@@UAERCADDICTSvery nice man
Are you running that motor on 6s or 8s?
Both depends on the race
So the 2700kv can handle 8s. Thank you for the response. I wasn’t sure if it can handle 8s.
@emersonsiapo8094 for 1 to 2 runs yes then let cool down distance 132f donot over gear max 26pinion
Ok thank you for your advice.
I got the 2700kv kill mode. What diff gears are you using? 3.3 or 2.8?
Nice🎉🎉
AWESOME VIDEO 👌🏿🔥🔥🔥🔥🔥🧯⚙️💯
Great video thanks for the tips and info. 👍🏽🤙🏽💯
Question what did you mean by gearing should match kv ?
I meant dont over gear your motor remember this is drag not top speed
@@UAERCADDICTS ok thank you
no need gyro???
Yes you need
what type of gyro??
Kafuuuu🎉
I know the 1/10 scale drag is 132 feet so wouldn’t 1/7 scale car need more feet to be in scale with the car? Just a thought.
Yeah its 188ft but everyone has always just used 132ft as the standard.
Yep
سولف عربي حنا ندور عرب يفيدون هالهاويه
المشكله تعليقاتهم سلبيه وعددهم قليل
🫣🤫🫢🤐