FrSKY GPS Advanced Sensor. FBUS and logs
Вставка
- Опубліковано 7 сер 2024
- FrSKY GPS Advanced Sensor with FBUS and logs.
Ethos Tandem X20 Archer GR8
www.frsky-rc.biz/ws/sensors/f...
Like, Subscribe & Ding the 🔔 - bit.ly/ANsubscribe
🔎 More information 🔍
► Newton Airlines Uncut - bit.ly/NewtonAirlinesUncut
► Newton Airlines blog - newtonairlines.blogspot.com.au
► Links for my build materials - newtonairlines.blogspot.com/20...
► Andrew Newton UA-cam - / andrewnewtonaustralia
► My portal - anewton.net
► My Thingiverse - www.thingiverse.com/andrewrcn...
► iNav Basics and FAQs - newtonairlines.blogspot.com/s...
► All my iNav CLI Dump files - bit.ly/2t2OPz7
► Depron Armin Wing build - • Depron wing build
► Skyshark P4X spars - www.kitesandfunthings.com/Pro...
► GBC EZLOAD laminating film (May be discontinued) - shop.quadient.com.au/products...
► Alternative 75 micron laminating film (not tried by me) - www.boundtoimpress.com.au/sho...
► Depron and foam board - My 6mm and 3mm depron came from www.tradewarehouse.com.au But from 2020 it seems they no longer sell proper depron. I have not found another supplier yet.
👌🏽Support this channel 👌🏽
This is a fun hobby for me, not a money making venture. I don't have a Patreon account, and choose the minimum possible advertising option. However if you would like to support this channel here are some options -
►Direct donations to Paypal.Me - paypal.me/apnewton
►Affiliate links - BANGGOOD RC - bit.ly/3mMnJ93
If you use the affiliate link to make a purchase I may receive a commission at no extra cost to you.
👀 No single review will tell the whole story. Be clever, watch other reviews and shop around before making any purchase.
#AndrewNewton #FrSKY_GPS_Adv #FBUS
Videos are always great source for the state of our hobby. I don't use these components but enjoy keeping up on things.
I have the s-port gps sensor, haven't used it in a while because it took ages to get a sattellite lock. Also speed readings were inconsistent, maybe because of low refresh rate. Wonder how this new 'advanced' one performs.....
Nice, I've been using mine but wasn't successful with getting gps positioning done, but I am going to try your setup and see how it works. Thank you for sharing.
Nice video, thanks Andrew.
Thanks. You talked me into getting one, or maybe even two. regards
There is a program called ‚dataexplorer‘ that can also open the logs. I didn’t know it and thought I share it here
thenks
Andrew, with these sorts of videos where a product is being promoted/commented on/reviewed, you must make it absolutely clear whether you are doing what you are doing because the product was either supplied to you discounted or free of charge. These are the basic rules of ‘influencers’ these days. Keep up the good work. Cheers
Thanks for your thoughts Peter. You can assume all products on my channel are supplied free unless I say otherwise. My personal rule is that videos must be watchable, entertaining and informative.
@@M-H433 Influencer etiquette mate. If it’s a freebie or a heavily discounted product the influencer should declare this every time. Andrew’s videos are genuine and down to earth which we all appreciate and there is no doubt that he may ‘influence’ what we buy or don’t buy. Simple as that.
@@peterhancox5268" INFLUENCER ETIQUETTE"........🤣🤣🤣 what a lot of BS. Your the only one who wants to be advised where the goods came from. Think you've got your hand on it.
@@davidwatkin1484 while "influencer etiquette" is a crock of shit, the FTC actually *_does_* require disclosure when reviewing and/or even going over how to use a product that was given to you by the manufacturer.
I think Andrews an informer he's not out there in his dickstickers covered in oil flying.
Boy seems a generational thing, seems handholding needs to continue into middle age for some.
Ciao Anddrew come sempre ottima spiegazione vado ad ordinarlo al più presto, quando hai tempo mi potresti insegnarmi una programmazione per aliante F3K e F5j. Ti auguro un Buon Natale
Thanks Rodolfo. I have done videos on full house and DLG programming.
Interesting point at the end: is there a way to use this with a Matek flight controller, for example?
No, this is designed as a receiver connected sensor.
After reading the error Message I think it should be possible to edit the Log file to get google eath to work...
Is there a way to set an altitude offset for flying at other then sea level
Reset Telemetry does that I think.
Hi Andrew, nice to see you moved to the better state 🙂. Have you joined a model flying club in SA? there are some nice clubs in the south.
SA is excellent. Have visited a couple of the clubs.
@@AndrewNewton I have the first gps frsky had via s-port, I found that from when I flicked a switch to tell me the speed it was about 5 seconds delay. example if I flick a switch to read out the speed at the fastest past of the dive then pull up it would give me the speed about 5 secs before. how fast is the updates to the transmitter now?
I didn't notice any delay, but you can call out maximum speed rather than current speed
Can this sensor be used with other receivers and is it only compatible with F-BUS? what about S-BUS? I have a flysky IA-10b receiver.
It is an S-Port sensor (not SBUS). FBUS is SBUS + S-Port. Confusing I know, but S-Port is only FrSKY
Lol...No shorts on today matey...😮😀😏🇬🇧 I'm sorry, I'll get my coat shall I..?.
Yes it was as wild and cold as an English summer
@@AndrewNewton Oh, Andrew, that hurt....😮😳....too near the truth...lol.
🇬🇧🇬🇧🇬🇧🇬🇧
I have this sensor
Unfortunately, the time is shown with a 2-hour delay
Have you had such a situation?
I will be grateful for your help
I have a Taranis X9D +
Don't know sorry. Might be a setting available if you click on GPS in the sensor list and then edit.
Would it serve this receiver for long range?
About 3km.
Hi Andrew. I'm having massive confusion getting my FrySky FLVS advanced Lipo Voltage sensor with FBUS cable from receiver connected up to the voltage sensor itself.. The FBUS cable i have has 6 coloured wires. Black, red, yellow, which splits off to a black 3 pin connector, then there are 3 other green, white, blue wires going off to their seperate single black connectors. I figured out from other videos that the black, red, yellow connector goes into the lower set of 3 pins on the lipo sensor with yellow on ground and black minus and red positive. I do not have a clue where the green, white, blue seperate connectors go. Its confusing. I have a FrySky Tarranis X9D Plus with a RX6R receiver in a Volantex SR65 RC Boat. Can you help or please make a video showing how to set up this FBUS green white blue cable. They come off the white FBUS connector and are going to nothing. I notice on the back of my receiver , the green is listed as Aux, white as SBus_Out and blue as SBus_In. I still don't know what these do and whether i need them ?
You probably dont have FBUS on your receiver. Yellow would be S-Port, so just plug that 3 pin connector (black red yellow) into the sensor (either set of pins, they are the same) The other three wiress are for other uses and can be just tucked out of the way. AIN2 is Analog IN (for an analog voltage sensor) SBUS OUT is for connecting to a flight control board, SBUS IN is for connecting a backup receiver. This older video shows the connection ua-cam.com/video/ztDvA_FFcfE/v-deo.html
Hi
Tried to compare the speed with that of DJI drone, came out it showed only 1/3 of the dji speed. Wrote to the supplier while still no response. Any glues from you
That's odd. Mine have both been pretty accurate compared to other GPS sensors.
I notice at 2:38 Andrew shows the Firmware download page which notes V1.7 "Fix the issue of having the abnormal telemetry value of GPS speed". You may want to check your firmware version.
Sure let me check
Indeed one could use DIY sensor to modify using ratio…. Anyway will explore your idea first. Thank you
Hello! I have a fiber glass glow sport airplane (150+ mph), can I install the GPS inside the plane? Will I get the signal? I can't install in the outside
Also, can I see the max speed that my plane reached on my radio after each flight? I have the X20s, I just want the gps to see the max speed that my plane gets
Yes to both. FG is transparent to GPS. Long press on GPS Speed to get Min or Max options
@@AndrewNewton Tyty!
Buongiorno Andrew ho comperato il nuovo GPS frsky ma non riesco ad impostare la distanza fra la radio e l aereo ho una radio Horus 12S con il nuovo programma Ethos ti ringrazio ciao
Yes you set it up in Calculated Sensor in the Telemetry page
First mate !!!;🍻💪
Legend!
the main power wire for these frsky recievers is so fine, how can it power all these servos and sensors? guess it must be enough, it's finer than the wire that goes to an individual servo
Power wire would come from your ESC or BEC so you can choose how thick it is. You might be thinking about the sensor wire?
@@AndrewNewton look at the archer SR10+ reciever, the power in wire you connect to is really fine, I soldered a servo connector to those wires and connected to the BEC 5V but I changed that and just plugged into an unused channel pins. But what if you're using all the channel plugs for servos? then how would you power it?
Use a Y lead to share voltage in with one of the servos. But if you're using 10 servos you should be powering them directly from a big BEC rather than through the receiver
@@AndrewNewton how do you wire them directly to the BEC? only run the signal wires to the receiver? That's a lot of soldering.
I only added two more servos for a camera gimble, maybe it wont overload the receiver
Regarding the cables and connectors: how long will it be before society considers using the terms 'male-to-male' and 'male-to-female' to be a hate crime?🙄
INies and OUTies maybe?
So it's only access? Can't use with just fport on r9m slim on old protocol I take it? All my gear is so old. Think elrs and a radiomaster boxer may be a better option then QX7 with r9 2019.
Lol.... I still have the radio you graciously sent......... It got good use
Works with S-Port