When the pins are shorted my lLED light does not flash.... also what happens if the transmitter button has been held for more than 15 secs.... how do you get it reset
Good morning dear Sirs, I have a problem with my Nice 300 stepper motor, it presents an error “ES” whenever I configure the beam limits before reaching the end of travel it stops and displays this error I would like to know how I can solve it . Tanks
After bridging the BT which should cause a flashing Led, what's next? I assume the system is on learn mode and you simply press a button on a receiver for a certain amount of time?
I know it's a bit late and you probably have it sorted by now, but for anyone else asking the same, you short the pins, hold the button you want to pair down about an arms length away, and then for me I heard two beeps indicating it was paired.
@@chipanddip790 Good morning dear Sirs, I have a problem with my Nice 300 stepper motor, it presents an error “ES” whenever I configure the beam limits before reaching the end of travel it stops and displays this error I would like to know how I can solve it . Tanks
The video above refers to products incorporating the 3 pins for its receiver function It sounds like you're referring to the DCBLUE Advanced, here is the link - ua-cam.com/video/gPUsBVk2SGc/v-deo.html
Good morning dear Sirs, I have a problem with my Nice 300 stepper motor, it presents an error “ES” whenever I configure the beam limits before reaching the end of travel it stops and displays this error I would like to know how I can solve it . Tanks
@@Lil0Kevin14 Good morning dear Sirs, I have a problem with my Nice 300 stepper motor, it presents an error “ES” whenever I configure the beam limits before reaching the end of travel it stops and displays this error I would like to know how I can solve it . Tanks
Good day. When setting the gate opening and closing limits, you need to press the stop button before the wheel hits the end stop on the track. This is when the gate is in the open position. Once its stopped, use the arrow buttons to fine tune the adjustment and then confirm. It will then verify the set up and then be saved. Hope this is the answer to your question. @@jbtsservicos
Hey can I please have your email address I tried adding 1 it worked only for a while I held on a button and now it transmitted buy doesn't move garage door
Worked perfectly. Thank you!
Quick and simple, thanks 😍
Works perfectly
You Deserve a Bells 😎 🙏
Where do I find the control card?
When the pins are shorted my lLED light does not flash.... also what happens if the transmitter button has been held for more than 15 secs.... how do you get it reset
How do i add a master remote to a receiver if I can't find the main master remote.
Quick and easy i got it to work thank you 🙏
Good morning dear Sirs, I have a problem with my Nice 300 stepper motor, it presents an error “ES” whenever I configure the beam limits before reaching the end of travel it stops and displays this error I would like to know how I can solve it . Tanks
Where can I learn how install a motor
After bridging the BT which should cause a flashing Led, what's next? I assume the system is on learn mode and you simply press a button on a receiver for a certain amount of time?
I know it's a bit late and you probably have it sorted by now, but for anyone else asking the same, you short the pins, hold the button you want to pair down about an arms length away, and then for me I heard two beeps indicating it was paired.
Nice
@@chipanddip790 Good morning dear Sirs, I have a problem with my Nice 300 stepper motor, it presents an error “ES” whenever I configure the beam limits before reaching the end of travel it stops and displays this error I would like to know how I can solve it . Tanks
Hi my door move down the other day but don't want to go up again
Hi I tried but now when I press my remote I only hear a click sound but it doesn't move
Please do a video on what to do when it reads “Learn Remote Comms Error”
My pins won't short out. Wat does that mean?
Kindly demonstrate to someone how to DIY by showing where the control card is located and how to access it
It's not it just show a P on the garage motor . What do you do after that ???
The video above refers to products incorporating the 3 pins for its receiver function
It sounds like you're referring to the DCBLUE Advanced, here is the link - ua-cam.com/video/gPUsBVk2SGc/v-deo.html
How do I add another remote I have done this step main remote works
Wrong video Yongama - I've sent you the link to the correct video.
@@nicegroupsouthafrica8683 please send me your email address
after me
after him
Hi, will my ET remote work on centurion D5 gate motor ?
No. You have to install a et rx2 micro receiver unit to the d5 motor. its a small hand unit that you can place inside the motor with no problem.
Good morning dear Sirs, I have a problem with my Nice 300 stepper motor, it presents an error “ES” whenever I configure the beam limits before reaching the end of travel it stops and displays this error I would like to know how I can solve it . Tanks
@@Lil0Kevin14 Good morning dear Sirs, I have a problem with my Nice 300 stepper motor, it presents an error “ES” whenever I configure the beam limits before reaching the end of travel it stops and displays this error I would like to know how I can solve it . Tanks
Good day. When setting the gate opening and closing limits, you need to press the stop button before the wheel hits the end stop on the track. This is when the gate is in the open position. Once its stopped, use the arrow buttons to fine tune the adjustment and then confirm. It will then verify the set up and then be saved. Hope this is the answer to your question. @@jbtsservicos
ua-cam.com/video/4PJRMGG0lnQ/v-deo.html
It didn’t work 😐
Ackicia Basson same here
Yah me too. What could we be doing wrong. Does holding it at arm's length make a real difference?
break on take
Ko9
Does not work
My garage motor beeps and shows 1 3 1 3 13 Etc. What is wrong
Hey can I please have your email address I tried adding 1 it worked only for a while I held on a button and now it transmitted buy doesn't move garage door