How to Safely Drill Holes in Sheet Metal Using a Twist Drill
Вставка
- Опубліковано 21 кві 2022
- Drilling holes in sheet metal can be dangerous due to the tendency for the material to spin uncontrollably or to climb up the drill bit unexpectedly. This can lead to severe hurty hurty! Often the hole will be distorted and the edges of the hole can be heavily burred. In this video I will demonstrate how to use a common or garden variety drill bit to safely drill neat and accurate holes in sheet metal. It works on any type of metal and some rigid plastics.
Check out Everett's videos here
/ everettsworkshop
Check out Haxby Shed's videos here / haxbyshed - Наука та технологія
That was the 1st time I heard of this technique, and I'm blown away by how well it works! Thanks for sharing that Mark.
Ditto, thanks!
I agree. It's a super tip I never knew I needed.
Same, but still not sure I would hold that by hand with my luck though.
That's great tip. I have never seen that in any books.
You won't. It is dangerous shop-practice.
This is a very old machinist trick that I learned years ago.
Good to see that this is still being taught to the younger generation ;-)
I'm 60 yrs old,,,,and just learned this,,,,hehe
Same. I was taught this by an old engineer when I was an apprentice. The cloth helps with absorbing vibration and preventing drill chatter too.
Great tip, which I've never seen before. I used to clamp the sheet metal between two pieces of wood while drilling, but your method is much simpler and quicker.
Sandwiching the metal between two sheets of plywood or MDF is safer and probably gives a slightly better result but it can be hard to position the drill bit over the marked out centre. I guess if you are very careful not to move the stock you could start the drill and then clamp the top layer of sheet material over the stock to be drilled. It would probably require three hands though! The cloth method allows you to start the hole exactly on a centre punch mark and then it's a simple matter to drape the cloth over the same point and keep drilling.
Regards,
Mark
@@Preso58 If you have a piece of plywood on the bottom, then a piece of plywood with the hole already drilled for the top, you can put the metal with the center punch mark in between and you'll be able to visually line up the center punch mark in the hole that is already drilled in the top plywood. Clamp the sandwich together and then you can put it on the drill press.
66 years later, I've finally learned to drill a hole thru metal. Where were you in the 70's? Thank you.
Even though I knew you would not drill , I was still having a heart attack!!!! Great demo on safety, danger, and how to do it properly.
Heart rate now back to normal.
Yeah, sorry about that. I wonder how many people switched off early?
Regards,
Mark
@@Preso58 : Certainly one of the best horror intros I've seen! I didn't switch off early, but I was entirely expecting you to drill it and produce a horrifying mess. (I would have guessed you to be holding it with a pair of long pliers just out of frame, and have your hands well clear, so it would only be unsafe for the metal ... just like you actually did later.)
Mark, your tip reminded me of one of my parents' neighbors having a workshop accident back in the '80s. He was a commercial airline Pilot that loved to build & work on "street rods." He was making or modifying some kind of sheetmetal bracket/box that already had it's final form, but needed more holes drilled in it. He made the mistake of not only holding it by hand (I don't know if he was also using a drill press vise), but also had one or two fingers that went into a hole. Needless to say, the drill bit grabbed the part and it caught him before he could get untangled. He ended up with his hand & arm wrapped around the chuck/spindle before the motor fortunately stalled out. He was *barely* able to reach the power switch to kill power and was lucky to not pass out from shock (he was working alone in his basement garage). He _almost_ lost the end of one finger and was in major pain as his finger slowly healed (set back in place with a pin & stitches) over the next few months. As a professional Pilot he was grounded until he could prove that he was fully healed. And, while the throbbing finger was healing, the most comfortable position was to lean back in a sofa with his hand leaned back above his head -- their housecat had a bad habit of needing to slap the ball on the end of the pin holding his finger in place while it healed! He said that didn't feel very good either....
Oooh! That sounds nasty. He was lucky not to lose one or more fingers completely. Perhaps there should be some sort of register or a case study forum to document these sorts of accidents. I am guessing you would need a strong stomach to read such a document but it would serve as a way to warn others about the consequences of these types of incidents. I know that in the aviation industry, every aircraft incident is investigated and the findings are published. My father in law was an aircraft mechanic working on propellers and he had industry publications with three of four accident reports in each one. It was fascinating reading. Not all the incidents were serious but sometimes the most innocuous circumstances led to disaster.
Regards,
Mark
@@Preso58 there certainly used to be medical textbooks on all sorts of industrial accidents (my dad was an FRCpath (path = pathology) and had lots of them which I used to thumb through as a kid - gruesome!
Yes this is proof that an accident that takes less than a second can have consequences that last months, years or life long!
Great tip Mark. Thanks. Both improved safety and accuracy. No more triangular holes!
Never appologize for scaring people. They should be scared. I love your video, good work.
Well, this must be the most useful How To video I ever stumbled upon.
I just recently obtained a chinesium step drill but this tip is worth its weight in gold. It just so happened I today got me a very nice, German made Metabo drill which has the power to do all sorts of hurt... And few weeks ago I found me an old Black&Dekker which is technically restored by now. The Metabo just needed cleaning. Now that I have two nice drills with a 1/10th mm runout- good enough for the girls I go out with.
Thanks Mark, You are a fine instructor, I´ll put this to work...
I am glad you found it useful. Like I say, you won't use the method every day but if it saves your fingers it is worth knowing.
Regards,
Mark
Thank you mark.
Every day is a school day i never imaged this would work,many thanks
Been metal working all my life, I just learned something thanks.
I am about your age. I have been reading shop tips since I was 9, and I have never seen this one before. My jaw literally dropped when I saw how simple it was and how amazingly well it works.
Grant. I used to read and re-read those old Model Engineer magazines. A model engineering club I belonged to had boxes of the really old volumes and they were filled with all sorts of gems. Sadly, I cannot remember them all but this method worked the first time I tried it so I guess it has stuck with me.
Regards,
Mark
OMG......I have been drilling holes for 60 years.....I am flabershausted that I never knew this. Thank you Mark :))
Never heard that cloth/twist drill tip. Thanks Mark
This is an amazing trick! I hadn't seen it before, but definitely will be using it in the future.
Good morning, I had this technique explained to me by my master once in 1984. I have never forgotten it and always enjoy using it. Warm greetings from Germany. Jens
You are the second viewer from Germany who has reported being taught this technique. Maybe it's a regional thing but having read lots of text books on machining and metalworking (mostly English, American and Australian texts) I have never seen it described.
Regards,
Mark
I've been fabing over 50 years and I can still say ya learn something new everyday , GREAT finer point Thanks.
This seems to be a common observation. I guess I would have missed it too if I hadn't read that obscure letter to the editor in the old ME magazine.
Regards,
Mark
9 stitches through the center of my thumb for drilling almost that exact shaped piece years ago
Hi Mark very useful and practical information. The style of the tin snips and the tin plate shaper take back to manual training at school (I still have both styles that family handed down to me). In my day metalwork/woodwork was done in grade 8 (and later at high school if students pursued an industrial course). These subjects set you up for life no matter what area a person chooses to work in. Thankyou
What a great tip! "There's no way that can work" describes my initial reaction, followed by "it's kind of late for an Aprils Fool's joke..." But wow, it actually works. Color me flabbergasted.
👍
I know it seems like an unlikely technique but it has worked every time for me.
Regards,
Mark
I will admit I had not heard of doing this for sheet metal until you had mentioned it. Still not sure I'd grab on to the work piece, but I'll definitely be using this trick! Thanks for the shout out (and I'm VERY sorry the response was so late!), and for "virtually" hanging out in my shop with me, lol!
Thanks Everett. I wouldn't normally hold the stock in my fingers either. I was taking a risk for artistic merit! However you have to work hard to make the drill bit catch when using the cloth technique.
Regards,
Mark
Excellent trick!
Trained and experienced machinist, and mechanic, 30+ years experience, never heard about this great tricks. I used to place the thin metal sheet, between 2 scrap aluminiun thicher sheet. less accurate. thanks for the tip. From QC Canada.
Fabulous technique, so useful, practical & economic. The number of times I have shed blood with thin stuff spinning on me tells me that I am a slow learner, but this is so swift & convenient that I will use it. Thank you for sharing!
Потрясающе. Если бы сам не увидел, не поверил бы. Я сам пару раз пострадал при сверлении тонкого металла. И сейчас смотрел с замиранием сердца.
Единственное что меня успокаивало так только то, что UA-cam не пропустил бы видео с плохим концом.
Большое спасибо, вы открыли мне новый и безопасный способ сверления. 👍👍👍
Пожалуйста. Я рад, что вы нашли это полезным.
Mark
@@Preso58 Очень полезным. 👍👍 Спасибо
I have been around for a while and also watched far too many hours of UA-cam machining videos, read a lot of magazines and books and this is totally new to me. Just goes to show, thanks for making my workshop a safer place.
The older you get, the more you learn. As long as you can retain it you're golden!
Regards,
Mark
Who says "an old dog can't learn new tricks"?......brilliant tip Mark, thanks for sharing!
One of the best drilling tips I've ever seen. Thankyou so much for sharing this technique.
Great tip, Metalwork teacher with 35 years of experience but you taught me something new today! thank you.
This old trick has been known in good engineering shops for decades, but with governments destroying manufacturing skills, I'm glad you're showing these things in this platform. 👍
I had someone tell me that it was commonly taught in German trade schools but I had never been shown the technique when I was training as a shop teacher.
Regards,
Mark
That sticker collection is just so adorable. That's a wonderful way to build community. I like that you put push pins in the map to show where they come from.
Well I'm straight out to the shed to try that out....
Back, no blood, and the best holes I've made in thin sheet. A lot quicker, and better results compared with the sandwich between two bits of wood I'd used.....up until now :-)
Thanks for the video Mark. Great stuff.
Cheers
Pete' New Zealand.
I'm glad it worked for you. Thanks for watching.
Regards,
Mark.
I'm 72. A kiwi. Your never to old to learn. Thanks for the tip cobber. Wish I had known that many years ago.
Sir, I've worked with metal in fab shops and at home for some 48 + years and have never seen this trick! This is Brilliant. thank you for sharing. Can't wait to try it out in my shop.
This is the most useful video on UA-cam, amazingly simple solution to a well known problem!
Teenage me did in fact attempt to drill a piece of sheet metal in shop class and got my palm opened for it.
Dear Mark, thanks for sharing this brilliantly simple but elegant idea. I’ve had that problem of metal catching & spinning but I still have all my fingers & thumbs.
Incredible results. Magic before our eyes. Thank you for sharing 👏👏
65 years of building, machining, and drilling holes and this is new to me. Even after reading 40 years worth of Popular Mechanics starting in the 1920's.
That’s absolutely excellent I’m very impressed with that technique, that is most definitely logged in my mental tool box now ! Thank you
Good idea !!!
Thank you and hugs from Brazil.
Your house and garden are the picture of paradise!
Congratulations.
Thanks for watching and the compliments!
Regards,
Mark
Wow! it took me till now to learn this,no more doing it the wrong way,Thanx Preso.
I've heard the 'use a bit of cloth' tip before, but never with any explanation. Your video made it perfectly clear. Thank you.
Oh! What a technique. What surprises me is how does wisdom evolve and work.
Very clever, simple yet effective, thanks for sharing.
I have never seen this technique before, and I'm going to try it out soon
On some clamps that are WIP.
I've always been wary of drilling sheet since seeing a fellow
Apprentice slice his thumb through,
That was over 50 years ago, so your never to old to learn.
Thank you
Thanks Michael. It is certainly a useful technique especially for those jobs where you need a large but clean hole in thin stock.
Regards,
Mark
I'm 54, all my life in metal shops and I did not know this trick.... very good... thanks
G'day Presso. I knew from the start it was a set-up but it still sent shivers
shivers down my spine. I've read about the use of a piece of cloth but never seen it done, thank you.
Cheers Peter
Thanks for that tip Presso,, been drilling triangular holes in sheetmetal for as long as I can remember,, used the plier or clamp method but still had a few get away from me. Must try
this trick next time. Thanks for your continued great content.
Brilliant! I’ve been a Machinist since 1967 and never seen this before. I’ve always used the step drills, Brad point or punches.
Brilliant- I’m 65 and I’m only learning this now
Great tip, thank you. Also a big Thank You for referring to where we all work as a Workshop.
AWESOME! Sending to lots of metalworkers here in South of Brazil!!
Funny note: I played the video and started eating without watching, just had it as a background, then I heard the crows at the beginning of the video and I immediately knew you must be an aussie youtuber :D
This is a great tip Mark. I wish I knew this long ago. It would have saved me from all of those drill press helicopter episodes that I have had in the past...
It's definitely a finger saver!
Regards,
Mark
That's a wonderful technique! Thanks for sharing.
Hi Mark, great video. A couple of years back I had to make a new anchor hole in an old French mantle clock main spring. Very hard, very thin and narrow. The recommended method was to punch a hole but not having the appropriate punch I made a sacrificial tool from two pieces of flat strip welded together at one end with the appropriate size hole drilled through, placed the end of the spring between and clamped down as close to the spring as possible. It worked perfectly but it took a lot more time than your technique and left burrs on both sides of the work piece.
Gary, I have seen people punching holes in clock springs. They seem to be unwieldy and difficult parts to work with. Not for the fainthearted! Drilling would be a real challenge.
Regards,
Mark
You are a life saver!
Thank you so much for being so clear with your explanations.
Thanks for sharing this very useful information. Tried it this afternoon by drilling a 5/8 inch (15.875mm) hole in a piece of 0.6mm galvabond without a pilot hole. Worked perfectly with minimal burring, although the drill was very sharp and only run at about 180 RPM. Thanks again.
I am glad it worked for you.
Regards,
Mark
Amazing, absolutely great tip, I'll never forget it.
wow! mind blowned! that was a really good hole in sheet metal. can not wait to try that myself! thanks for sharing Mark!
Wow, I'm blown away, will use this trick for sure, thanks!
Ok I admit it! You totally got me with the drill bit moving toward your piece of metal!! Haha - I was sitting there thinking 'wait, that's a terrible idea - is he actually going to be able to hold that?'
Yeah, sorry about that. If you know, you know!
Regards,
Mark
That's absolutely amazing. I drill holes in sheet metal on a daily basis and this will save a lot of time and trauma.
Every day is a school day. I never knew that. Thanks Mark.
Great tip there Mark, thanks for sharing.
Great tip there Mark. I had heard about it some time ago but had never seen it demonstrated. Like you I was sceptical but now cant wait to try it. You have some interesting wildlife there too.
Guys, we just witnessed one of the last few tricks that haven't been propogated across social media. Help Mark out and make this thing go viral!!!! This thing should have 2.5 million views by the end of the month if we help him out. Share Share Share
Awesome advice Mark.. thanks .. more of these tricks please!
Great Video Mark. Thank You
I had always problems with drilling thin metal sheets. Looks so easy when you doing it, I'll try that tomorrow at work :D
Greetings from Poland!
Awesome trick, I've never seem that before. I originally came here for your engine build series. Glad I stuck around.
Great tip, thanks for sharing your knowledge and experience.
That is one I have not seen in machining! I usually just suggest sheet metal drills and/or proper clamping and/or fixturing. Great tip sir!
Nice technique Mark! I don't do much sheet metal but it's worth remembering. Thanks for sharing 👍
Beautifully clean hole. Neat.
Thank you Mark for that useful tip. I don't know if I will ever need it, but it's good to know.
Brilliant Sir !! You saved my Life today 👍🏻👍🏻👏🏻👏🏻
Damn! That's brilliant! Definitely the most useful video I've seen in months
Good Show Mate: I knew about this method. I've never had the need to use it. That could change tomorrow. Good reminder. Thanx.
Yes yes! The old cloth trick. I heard about this some 35 years ago from an old guy. Went through a tech school and it was never mentioned. Priceless lessions for younger generations. Keep em comming 👍
sir what kind of cloth.?
kindly reply
a. can we use cotton waste available in workshop!
@@sureshshree any cloth. Old jeans, cotton, towel...
Thank you Mark !!! That is such a helpful tip, I am going to teach that to everyone I know, Thank you again !!
God bless you for sharing with us your useful tips and tricks. Very useful
Excellent tip, I've spent pretty much my whole life in shops and never heard this one. Would have saved me at least two nasty scars!
I trained for three years at college and never heard of this technique either. Nor have I seen it in any text book!
Regards,
Mark
Thanks for that Paul....Smashing safety tip
Thanks for the tip. Very useful.
I loved the nature shots.
Dave.
After all these years. Thanks for the great tip!
Awesome technique. Many thanks for sharing!
Awesome tip! Thanks for making this video!
I have never heard of this. It's impressive!
New technique to me. As it happens in installing a double DIN radio I need to drill the sheet metal mounting brackets to mount the radio a bit lower. It struck me as dodgy business to drill the holes without the drill grabbing it and bending and hurting my hand. Thanks for the tip. Nice roo shots. I’m in Perth and we have quite a mob of Roos at a local monastery.
Wow, that is a really useful tip. Thanks. I always have trouble when drilling out clock pivot holes when re-bushing.
Thanks for sharing this. It looks like a very effective and useful technique.
Never seen that before, excellent idea. Thanks for sharing
Fantastic Tip, I'd never seen this before. In the past I've always used clamps and progressively larger drill sizes and/ or a Step Drill bit. I will definitely use your method in future. Thanks Mark
Thanks for watching. Step drills are great but the big advantage with this method is that you can drill any size you have a fractional or metric drill bit for.
Regards,
Mark
Amazing ! Never seen this before. It's almost magic.
Great shop tip!
Very keen to see the start of your next project Mark
Me too! It is sitting on a shelf awaiting some attention but other jobs keep getting in the way!
Regards,
Mark
@@Preso58 My wife is getting sick of me going straight to your channel to check for a start every time I turn the TV on.. LOL
Great tip , thanks for your knowledge!
Fantastic! What a great tip. Going to try that real soon.