Awesome job with your rc sub. Will you release stl files and pdf instruction for sell in the future? There are so many things to learn from your channel.
I get that pulling the syringe cylinders in draws water into the syringe sleeves to create negative bouyancy. Where does the air go that’s pushed out? Into the compartment with the servos, batteries, and receiver. Is that air just compressed. Because, more importantly, where does the air that replaces the water that was pushed out of the cylinder to surface come from? Subs use compressed air for this. Is your compressed air what’s in the electronics compartment? Very nice build btw! Well done!
Seems like it has an initial buoyancy higher than its weight and by taking in water, it increases its weight and decreases its buoyancy so it sinks. When the water is pushed out again, the initial buoyancy is restored and brings it up to the surface again.
@@doubleT84 That part is obvious, but where does the air in the other side of the syringes go? Is it compressed in the syringes or is there a vaccum in the syringes?
@@coolbionicle The other side is open to the compartment. Pressure inside the compartment might increase slightly ... but so does it by being under water.
So if I understand correctly, it uses water instead of air to control the weight of the submarine. Opposed to how it's done in real life, in which compressed air is used.
First off, I like how you did this. I am using the same 1:72 Revell Type VII submarine model as a basis for an RC-submarine. You will need around 350ml to submerge it fully from it's original water line. If you thin out the parts above the water line you need even less. That is if your air tight compartment is completly below the water line. I propose that you test this out in a bath tub without any internals first. Now the problem that I see (and I have been there before). When you submerge you compress the air in the water tight compartment (where all the electronic is). That does not sound like a problem since you uncompress it when ascending. However with the small scale of the submarine it's quite hard to make a pressure vessel that is air tight enough for even the small amount of pressure that you will build up. You will leak air when descending and pull in water when ascending. Maybe you can manage that better than I did, but I couldn't get it to hold the pressure. Another problem is the force to move the syringe. You might want to calculate it first or else you could end up in a situation where your small motors don't have enough power to evacuate the syringe against the water pressure. Since this video is somewhat old and I don't see any further videos with a working model I am assuming that you have noticed the same issue. Good luck.
For now, the submarine is working very well and there is no strong pressure or water flowing back in when the dive comes to the surface. A total of three torpedoes will be fired and a vertical missile will soon be completed. Thank you for sharing your advice and experience. There are more detailed photos and short videos on my Facebook page. Information shows my Facebook address.
When you build it with Quadcopter Flight controller or add an Gyroscope then you could fill the Tanks inependitly then the Uboot can dive and breathe level. Without lesty Metall leveling
hello mr I have the same model Revell 05166 Model to build German Type IX C submarine, scale 1/72 did I carry out a conversation with you in rc did you do it in 3d the ballast after this you had STL file thank you cordially
Wow - amazing job, really impressive. Flashforge should be sponsoring you. This inspires me do do more stuff on my printer. Thanks for such great vids, amazing work.
이거보다 스케일업한 버젼은 그냥 아예 엑츄에이터를 양쪽 시린지에 하나씩 달아서 엑츄에이터 드라이버를 그냥 RC에 연결하면 되겠군요. 근데 함정은 물에 깊이잠수할수록 RC 시그널이 똥이된다는거... 뭐 자율주행 알고하고 기압측정기 (바로미터) 하나 달아서 깊이 측정하게 하면 될거같은데... GPS는 시그널이 잡혀야되니 안될거같고, 엑셀로자이로 한 3개 달아서 측정값 보내게 하고 배드시그널 나오는애는 그냥 데이터를 안받는 (majority vote) 시스템으로 하면 될듯 시중에 나오는 셀피캠 잠수함들은 그냥 줄이 달려있는데, 그럼 재미없죠.
hello mr how are you I bought this model Revell 05166 Model to build German Type IX C submarine, scale 1/72, Gray and I want to modify it in rc like you and what it would have possibility of help is this that the batteries I can change them to install a Lipo and know which amperage variator for the motor pushes propellers I await your return cordially thank you
This submarine kit was bought 15 years ago. I don't know if it's still available, but if I were to make it again, I would probably print the entire hull with a 3D printer. Want to help me with my build? Send me lots of pictures and descriptions of your submarine to the email posted on UA-cam.
Hi, you did a really great professional job. Your suggestions are gorgeous and really impressiv! Do you offer somewhere the stl files for wtc and gearbox? Btw cool kid :-)
이해가 안되는 부분이, 주사기 내부에 물이 들어가면 잠항이고, 빠지면 상승입니까? 자체무게로 주사기 내부에 물이 빠져도 그대로 가라않을것 같은데. 아니면 반대로 주사기 내부 공기가 채워져 있고, 잠항시 주사기 내부 공기를 빼면 잠항이고, 공기가 채워지면 상승입니까? 그러면 잠항시 빼낸 공기는 따로 저장해야할 산소탱크가 필요한데, 그렇게 되면 결국 양쪽 주사기 내부 공압이 빠져도 산소탱크에 에어가 차있으므로 잠수함은 잠항이 안될것인데, 어떤원리로 잠수함모형이 상승과 잠항이 되는지 알고 싶습니다.
처음 말씀한 부분이 맞습니다 주사기안에는 공기가 있어 부상중인 상태에서 모터를 돌려 물을 채우면 있던공기는 잠수함내부로 압축되고 물이 들어와 부력이 약해지고 무거워지니 잠수하게 됩니다. 다시 물이 빼면 압축된 공기가 주사기로 채워지고 가벼워지고 부력이 증가하니 상승합니다^^
가변저항을 보면 서보조종기판으로 연결된 3개의 선이 있는데 com이 아닌 두개선에 저항을 연결해줍니다. 그렇게 연결하면 횡거리 변화가 증가되니 주사기 길이가 길때 유용합니다. 적정 k옴을 달아보세요 의미는 횡거리 증가입니다.저항을 올리면 조종스틱의 최소최대 조종시 서보의 회전 거리를 더 증가시켜 줍니다. 슬라이드저항은 3개선 위치가 어떤것이 중간인지(com) 파악하기 힘든데 카탈로그를 보거나 하나씩 변경 해주면 파악이 빠릅니다
![LaLaRC [라라RC]](http://yt3.ggpht.com/ytc/AIdro_k_yqsr6uuqWva1B_q4tVSzwi3lgLez4ei9y8CJW0dqqX0=s48-c-k-c0x00ffffff-no-rj)
![Lp. Сердце Вселенной #60 РОЖДЕНИЕ ЛОЛОЛОШКИ [Финал] • Майнкрафт](http://i.ytimg.com/vi/YoR0pAV9FVQ/mqdefault.jpg)
구독과 좋아요 부탁해요 다음편이 빨라집니다ㅎㅎ
Subscribe and like, please. The next episode will be faster.^^
Awesome job with your rc sub. Will you release stl files and pdf instruction for sell in the future? There are so many things to learn from your channel.
Thank you, I shared some STL files with only 100cc syringe in the UA-cam description section. I also shared it with my account at www.thingiverse.com
Torpedo is a great detale and all the details on the submarine are so good
Good job 👍
@@LaLaRC 마지막에 F-35 B 수직이착륙기 엔진 노즐 이네요 👍
도대체 얼마나 천재여야 이런걸 할수있는거지
아우 저거 톨러런스 맞추느라 골나갈듯
미래 인재가 자라고 있습니다.
감동적입니다.
보는 것만으로도 힐링이 되네요. 어렷을때 참 좋아했는데 이젠 아재가되어 굳어버린 손과 머리. 영상을 보면서 덕분에 힐링합니다.
와 진짜 멋있는 작품입니다!!!! 진짜 대단하세요
I get that pulling the syringe cylinders in draws water into the syringe sleeves to create negative bouyancy. Where does the air go that’s pushed out? Into the compartment with the servos, batteries, and receiver. Is that air just compressed. Because, more importantly, where does the air that replaces the water that was pushed out of the cylinder to surface come from? Subs use compressed air for this. Is your compressed air what’s in the electronics compartment?
Very nice build btw! Well done!
Seems like it has an initial buoyancy higher than its weight and by taking in water, it increases its weight and decreases its buoyancy so it sinks. When the water is pushed out again, the initial buoyancy is restored and brings it up to the surface again.
@@doubleT84 That part is obvious, but where does the air in the other side of the syringes go? Is it compressed in the syringes or is there a vaccum in the syringes?
@@coolbionicle The other side is open to the compartment. Pressure inside the compartment might increase slightly ... but so does it by being under water.
So if I understand correctly, it uses water instead of air to control the weight of the submarine. Opposed to how it's done in real life, in which compressed air is used.
아무리 봐도 미쳤음 ...
천재가 분명 합니다
ㅅ.ㅅ
어뢰발사에서 빵터짐. 대단하십니다. 최고!
Bravo monsieur, merci beaucoup pour votre travail honnête et courageux car il permet l'inspiration et l'assurance pour les futurs ingénieurs 😉👍
대단한 열정과 천재적인 감각이라는 말밖에 안나오네요 재관둥이님이 한번 소개해주시면 구독자 떡상할 듯요...
네 천재까지!!! 칭찬 감사합니다 대한민국인의 긍지와 자부심 한번 보여주려고 합니다 재관둥이님 개인적으로 팬입니다
미쳤습니까 휴먼? 3D 프린터 활용 잘하시네요
If you were to make these into kits somehow, I honestly think people would be willing to pay hundreds of dollars for them.
I was thinking the same thing. We should talk offline
Try closer to $1000, this is hardly a toy, I’m sure the maker knows this
try thousands
I paid your hardwork with never skipped the ads
You better send him money
First off, I like how you did this.
I am using the same 1:72 Revell Type VII submarine model as a basis for an RC-submarine.
You will need around 350ml to submerge it fully from it's original water line.
If you thin out the parts above the water line you need even less.
That is if your air tight compartment is completly below the water line. I propose that you test this out in a bath tub without any internals first.
Now the problem that I see (and I have been there before). When you submerge you compress the air in the water tight compartment (where all the electronic is). That does not sound like a problem since you uncompress it when ascending.
However with the small scale of the submarine it's quite hard to make a pressure vessel that is air tight enough for even the small amount of pressure that you will build up. You will leak air when descending and pull in water when ascending.
Maybe you can manage that better than I did, but I couldn't get it to hold the pressure.
Another problem is the force to move the syringe. You might want to calculate it first or else you could end up in a situation where your small motors don't have enough power to evacuate the syringe against the water pressure.
Since this video is somewhat old and I don't see any further videos with a working model I am assuming that you have noticed the same issue.
Good luck.
For now, the submarine is working very well and there is no strong pressure or water flowing back in when the dive comes to the surface. A total of three torpedoes will be fired and a vertical missile will soon be completed. Thank you for sharing your advice and experience. There are more detailed photos and short videos on my Facebook page. Information shows my Facebook address.
Nice, like to watch 💪👍 greetings from Germany Bro 👍
Your grand grand grandfather probably the designer of those things 😂
@@jasonnnnnnnnnnnnnnnn8352 big mother of nope, he never served in the military.
Hay hai L.J
당신은 미친사람인듯... 탐이나요 당신의 재능~ㅋ 구독은 필수^^♡
감탄입니다 와우~~
맥가이버가 울고갈듯요.
진짜 감탄했습니다.^^
새로운 문물에 눈을 번쩍 뜨고 갑니다
잘 보고 갑니다
헉 우리나라에는 아직 모르시는 분들이 많지요 ㅠ 시청 감사합니다
사람이… 이런걸 제작 하는게 가능 하군요!!!!!!!!!! 대단 하십니다!!!!!!
This honestly showed me how a submarine works lol.
I've always wondered how they could rise after submerging. I feel dumb now
우와 역시 세상은 넓고 고수는 많네요.
3D 프린터 상용화 되기전에는 일일히 포멕스 1.5T부터 3T짜리 사서 깎아 만든 추억이 있는데 요즘은 그냥 잠수함 헐부터 벨러스트 탱크까지 전부 뽑을 수 있어서 편하겠네요. 만들어볼려고 레벨제 1/72 유보트랑 트럼페터 1/144 시울프 사려고 돌아다녔던 기억이...
슬라이드 가변저항은 진짜 생각도 못했네요~오~!!
유튜브상 최고인듯 합니다!
where does it get the air to displace the water that was pushed out? wouldn't electrosis be a better source to push the water out.
Cool build man. I like the sound track
와 신기하다 이거 하려면 전기도 잘알아야겠네요 ㄷㄷㄷㄷ
정말 대단 하십니다. 완성된 모습 보고싶어지네요!~~~
저도 완성을 해야하는데,,ㅠㅠ 뭘해도 서강진님 보다야 못만들지요 ㅋㅋ
와 .. 미쳤다 ㄷㄷ 장난아니시내요
보고있으면 다음편이 설레서 콩닥콩닥 거림 ㅋㅋㅋ
Awesome build bro your very smart just joined the rc family 😎👊👍
Mate how much the price with shipping to germany??? I ask for a friend
I don't have any sales plans. Sorry, thank you for watching.
스트리퍼 없이 니빠로 기양 피복 벗겨버리고,
서보를 저렇게 이용할지는.. 리니어 포텐쇼미터 서보 포텐쇼미터랑 연계.. 천재 입니까!?
하....’ “” 아따마..”” 아 시
잘하시네요 재능 낭비하시네 ㅋㅋㅋ 짱이시네 굿 👏🏻👏🏻👏🏻👍🏻👍🏻👍🏻 와우
정말 멋지십니다 판타스틱
f35 제작하시는거보고 영상 다보고있습니다. 찐 금손 대단하십니다 bb
구독, 좋아요, 알람설정 박고갑니다~^^진짜 멋지십니다~^^
영상 첨보는데요. 대단한 기술이십니다.
저도 못쓰는 드론이나 rc카로 만들어보고 싶었는데 실제로 만드시는건 첨보네요.
칭찬 감사합니다^^ 저도 몇년간 생각만 하다가 끝까지 만드는 끈기를 내보려구요~
와 진짜볼때마다놀랍니다
예전에 설레임 아이스크림 포장지로 부력장치 만들었는데 요샌 3D프린터 덕분에 아예 주사기 자체로 부력장치를 만드네요 미세조정까지 되니 상환적이네요.
설레임ㅎㅎ고수시네요 그시절급 설레임만큼 좋은건 없었다고 한것 같아요. 스틱으로 탱크용량을 알수있어 더욱 발전되었지요^^ 칭찬 감사합니다
What an amazing works! The details is awesome woah
대단하십니다 존경합니다
Amazing work... new ideas too. Your boat has more features than the last two of mine combined!
모형전함함선카페 보고왔어요. 대단합니다!! 구독했어요!! 화이팅!!!
헉 구독 감사합니다^^ 힘이 엄청 납니다~!
well done, it could be the central brake system, it could be the handbrake, have a nice day.
When you build it with Quadcopter Flight controller or add an Gyroscope then you could fill the Tanks inependitly then the Uboot can dive and breathe level. Without lesty Metall leveling
채소 금손이시네요...
Great video editing! You are a great engineer! Nice brain 🧠
와~~~대박!
존경스럽습니다
Pretty entertaining,hi from Honduras :-).
Ох ты и заморочился)супер
알수없는 알고리즘 덕분에 구독 누르고 갑니다. 그냥 최고네요!!!
Ванная для людей или для собак? Больно маленькая
это человек Длина подводной лодки 1 м.
@@LaLaRC ясно. У вас талант, всё шикарно получается. Удачи.
Clever!!!!!!!!!!!! 👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼
hello mr I have the same model Revell 05166 Model to build German Type IX C submarine, scale 1/72 did I carry out a conversation with you in rc did you do it in 3d the ballast after this you had STL file thank you cordially
Will it receive signal under some meters of water?
I haven't actually done it, but since it's 72mhz, it looks like it can be five to eight meters deep.
Wow! 😳 You are talented!! 👏👏👏👍
السلام عليكم ،very nice work ,thanks
Yeh, if you would offer it as a kit to buy for assembly- I would be first in line to get 2 kits.
Hi :) Love your videos. You have mad skills and are really funny. Super cool that you also show failure and when thing go wrong. Enjoying allot :):):)
Awesome work! Big hug from Colombia
Wow - amazing job, really impressive. Flashforge should be sponsoring you. This inspires me do do more stuff on my printer. Thanks for such great vids, amazing work.
다음편은 정신나갓...... v2ㅋㅋㅋㅋㅋ미사일 ㅋㅋㅋㅋㅋ
ㄷㄷ
@@pistol_sniper 여기서도 보네
@@SUKHOI-57 어디서 보셨나?
@@pistol_sniper 트위치
@@SUKHOI-57 아하
This is amazing. Great job!
Какой диаметр нажужний? У самой пластиковой трубы
Самый большой акриловый трубка имеет наружный диаметр 60 мм и внутренний диаметр 54 мм.
I'm your big fan sir ❤️
와,대단한 금손 이세요,ㅎㅎ
이거보다 스케일업한 버젼은 그냥 아예 엑츄에이터를 양쪽 시린지에 하나씩 달아서 엑츄에이터 드라이버를 그냥 RC에 연결하면 되겠군요.
근데 함정은 물에 깊이잠수할수록 RC 시그널이 똥이된다는거... 뭐 자율주행 알고하고 기압측정기 (바로미터) 하나 달아서 깊이 측정하게 하면 될거같은데... GPS는 시그널이 잡혀야되니 안될거같고, 엑셀로자이로 한 3개 달아서 측정값 보내게 하고 배드시그널 나오는애는 그냥 데이터를 안받는 (majority vote) 시스템으로 하면 될듯
시중에 나오는 셀피캠 잠수함들은 그냥 줄이 달려있는데, 그럼 재미없죠.
진짜 가성비 있게 잘 만드시네요..
구독했어요~!!! 앞으로 정주행 하며 많이 배우고 싶어요~by 아빠두루미
구독 감사합니다. ^^!! 대한민국 아빠 화이팅~
hello mr how are you I bought this model Revell 05166 Model to build German Type IX C submarine, scale 1/72, Gray and I want to modify it in rc like you and what it would have possibility of help is this that the batteries I can change them to install a Lipo and know which amperage variator for the motor pushes propellers I await your return cordially thank you
This submarine kit was bought 15 years ago. I don't know if it's still available, but if I were to make it again, I would probably print the entire hull with a 3D printer. Want to help me with my build? Send me lots of pictures and descriptions of your submarine to the email posted on UA-cam.
저도 3D프린팅 배우고 싶네요
진짜 최고네요. 다만 배경의 메탈음악 좀 다른 잔잔/조용/편안한 걸로 바꿔주시면 안될지요? 뒤에서 누가 쫓아오는거 같아서 마음이 불편해요 ㅋㅋㅋㅋㅋ
느리고 고요한 음악을 했더니 지속시간이ㅜ 제가 만든 영상 보는 저도 잠이와서ㅜ 음악 선택에 신중해 볼께요 감사합니다
Can you share 3D files for the section that holds the parts? Also can you give a list of ALL the parts needed? Thank you for posting your work.
There are so many files that it's hard to organize the shared list.
I'm going to post it in the near future.Thingiverse
@@LaLaRC Can you pls share that part which holds syringes?
@@Rhythm_by_Harsh thingyverse in ~! Thank you
Hi, you did a really great professional job. Your suggestions are gorgeous and really impressiv! Do you offer somewhere the stl files for wtc and gearbox? Btw cool kid :-)
Thank you for the compliment, but the main wtc and gearbox are too many files and complicated to share. Please excuse me.
@@LaLaRC Thank you anyway for your quick response. Maybe you publish more on thingiverse. It would be really great.Stay healthy.
Where did you find the actual sub?
잠수함은 언제 완결인가요 ??
주사기 안에있는 기체의 부피를 줄여 잠수하는 방식인가요?
네 맞아요. 주사기안에 물을 집어넣으면 무게가 올라가고, 내부 공기는 압축되어 부력이 약해지니 잠수하는 원리입니다. 감사합니다
이건 재능이다 오ㅑㅏ..
대박이네요.. 저런각각의 움직임 제어른 서보?로하나보네요
네 모든것은 서보의 조종으로 이루어지지요^^ 칭찬 감사합니다, 핵심은 슬라이드 저항으로 직선 조종이 가능하다입니다.
이해가 안되는 부분이, 주사기 내부에 물이 들어가면 잠항이고, 빠지면 상승입니까? 자체무게로 주사기 내부에 물이 빠져도 그대로 가라않을것 같은데. 아니면 반대로 주사기 내부 공기가 채워져 있고, 잠항시 주사기 내부 공기를 빼면 잠항이고, 공기가 채워지면 상승입니까? 그러면 잠항시 빼낸 공기는 따로 저장해야할 산소탱크가 필요한데, 그렇게 되면 결국 양쪽 주사기 내부 공압이 빠져도 산소탱크에 에어가 차있으므로 잠수함은 잠항이 안될것인데, 어떤원리로 잠수함모형이 상승과 잠항이 되는지 알고 싶습니다.
처음 말씀한 부분이 맞습니다 주사기안에는 공기가 있어 부상중인 상태에서 모터를 돌려 물을 채우면 있던공기는 잠수함내부로 압축되고 물이 들어와 부력이 약해지고 무거워지니 잠수하게 됩니다. 다시 물이 빼면 압축된 공기가 주사기로 채워지고 가벼워지고 부력이 증가하니 상승합니다^^
능력자다 정말 ' ';;
Çok iyi yapıyorsun bide Türkçe altyazılı da. Olsa daha iyi olurdu
오~! 짱 멋있네요
Oh, that's fantastic Sir. Wow... :)
와 이분 떡상 하실듯
Very good job....👏👏👏👏👏👏
Amazing work👍👍
Fantastico! Que escala es el submarino?
es de un metro de largo. 1/72 scale
3d 프린트 할때 pla 쓰시나요 ABS쓰시나요?
기어같은거 프린트 후에 후처리 하시나요?
기어는 PLA+ 로 0.08로 프린트합니다. 후처리는 해본적은 없습니다. ABS로 기어를 뽑긴 어렵더라구요. 다뭉게져서 프린트가 되서 포기 했었구요, 잠수함은 느린게 묘미라서 그닥 기어 강도는 의미없고 모터가 외부에있고 물속에 잠기기 때문에 온도가 공기중보단 낮습니다. 참고가 되셨길 바래요. 감사합니다
3:45초 횡거리가 짧아 저항을 추가한다는게 어디에 추가하는거고 무슨 의미인가요?? 아직 제가 지식이 부족합니다
가변저항을 보면 서보조종기판으로 연결된 3개의 선이 있는데 com이 아닌 두개선에 저항을 연결해줍니다. 그렇게 연결하면 횡거리 변화가 증가되니 주사기 길이가
길때 유용합니다. 적정 k옴을 달아보세요 의미는 횡거리 증가입니다.저항을 올리면 조종스틱의 최소최대 조종시 서보의 회전 거리를 더 증가시켜 줍니다. 슬라이드저항은 3개선 위치가 어떤것이 중간인지(com) 파악하기 힘든데
카탈로그를 보거나 하나씩 변경 해주면 파악이 빠릅니다
Warum V2? Die wurde nie von einem U-Boot gestartet...
Respect from Turkey. I Like this video
서보에 쓰이는 로터리 저항대신 슬라이드를 쓰는거군요
빙고! 제대로 보셨습니다
Is the hull 3D printed?
No, it is uboat plastic model, This product is sold at a model store.
잠수함 내부도 밀폐라 주사기에 물을채우면 자연스레 잠수함 내부 압력이 상승할 거 같은데 그건 지장 없나요?
그 압력 버티도록 설계를 해서 괜찮습니다. 못버틴다면 아크릴관이 터지면서 깨지거나 마개가 빠집니다ㅜ 감사합니다
Absolutely 💯 genius 👏
님.천재인듯
Awesome! I created a 3d printed SSRN Seaview, but would love to print a bigger version and make it r/c 😊