Trying to find a rear tire that is skinny and extra large I think 29” with a reverse pedal break and disc break option on it. Do I need to have one custom built?
I'm running two different engines. One is a Run Well and the other is a ZEDA engine. Both are ported, balanced cranks, Tuned pipes, High Compression heads, Big Box Racing Reeds, Hotter Plugs, longer Intake Tube, and finally a Richer Main Carburetor Jet. Fuel Mix is 50 to 1, Stelle Chainsaw Full Synthetic Oil and 92 octane gasoline. Stock these engines put out about 2.2 Horsepower. With my Mods and if I ran the math correctly, I'm getting about 9.2865 Horsepower. The bike is an Aluminum Flat Frame 26 in. Beach Cruiser, running 2.25 wide Tires at 50 lbs. This thing can really get up and go, climbs the hills like a goat. What a hobby. Thanks for the info.
Pro tip: with the proper piston that matches the bottom end, all the cylinders have similar enough port timing to be inter-changeable. I was hard up and needed an emergency jug replacement and discovered my cylinder from an older "type A" piston engine worked with my Zeda80, which has the longer connecting rod, and requires the type "B" style piston or as Amazon usually calls them, "high hole" piston. Only thing is, the stud spacing on the intake port- it's either 32mm or 40mm and youd have to get a different intake pipe if you changed cylinders and ended up with a different measurement, but I assure you the cylinders will work in every aspect but that one.
I used your videos to build my "Beast" with ZERO EXPERIENCE. The manual that came with it was pretty much USELESS. I was totally in the DARK as to -- HOW -- I was going to assemble this thing. I looked at LOTS of videos and was SO LOST as to what needed to be done. THEN --- I found your video tutorials. WOW. These let me know -- EVERYTHING I NEEDED TO KNOW in how to build one of these little bone shakers. Your videos couldn't be any more SIMPLISTIC and --- UNDERSTANDABLE. After I built mine, I had various minor glitches that wasn't anything too hard to figure out. My little Beast probably is running about 35 plus MPH straight as is stock. Very rarely do I get it at full throttle as I come up too fast onto the stop signs. After I break it in good i plan on adding a couple of high performance parts. I do not plan to bore it out or anything drastic, just add maybe a Boost Bottle and a Combustion Chamber muffler. I don't think I have enough room to add a large carbureator. I may or may not have enough room for a high compression head, but I'm not really sure. I do know about the Jack Shifter, but I really don't wish to run it at about 65 to 75 MPH after utilizing all 21 gears. It's a MOUNTAIN BIKE for God's sake. My little "Beast" really flies as it is and I'm really IMPRESSED with it. I have had a Honda CB200, a Honda PA50 Moped, and my favorite - the Tomos 2 speed automatic Silver Bullet moped. But NEVER something like THIS LITTLE THING. And --- YES --- I thoroughly believe in helmets and NEVER ride without one, unless I am using a Motor less Bike. You can ask Gary aBusey about that one. Ha ha --- ha -ha.
@@nadronnocojr I've seen some really poorly executed and produced videos with like no effort put into even the simplest editing, or bother to check if you can understand the audio. lol
I really appreciate your videos in regards to the motor itself I found a decent motor kit for about $150 everything except for the motor and the crankshaft is made relatively cheap but for 150 bucks yaheeda has the best motor kits for the price in my opinion
I must have gotten lucky because my little 50cc runs like a scalded dog lol it was a gift because he bought the cheapest kit he could find and couldn't get it to work correctly, I opened up the intake and took out the center of the exaust, tightened the sparkplug down, tightened the carb down because he had it loose... put some 40:1 in it, zoomin now...
a motor is basically a pump. Increase flow and increase rpms. Clean ports, good pipe and a balanced motor will increase rpms and power. First clean ports, then a good expansion chamber and a properly jetted carb will help
Thanks for this brief intro to motor prep. It was helpful. Wish I would have did more research before I ordered the 97 dollar 2 stroke. Luckily I havent put it on yet, so cleaning up burrs will be less dirty lol. Im just worried about touque for hills. I do have a 44 tooth. think i might bump it up a bit though. Bought my motor and its been sitting in the box for a couple months lol. Lazyness I guess.
I’ve had the chain tensioner go into the spokes going 32 and is was not fun. It basically just tore up the back wheel in the worst way possible. But I didn’t crash! Thank god. I skidded for about 40 feet
Thanks for videos gizza here from england, I've just got YD 100cc engine will my 80cc carburetor and my coil fit on my new engine, can you let me know please
I like the runwell motor with upgraded bolts .the crank is tight and the only problem I see is the clutch bearing needs upgraded to a better bearing then the cheap one that is stock.the stock carb is fine but the air filter needs more flow then the stock one lets it get.i use a skateboard wheel on my chain tensioner stock bracket to replace the plastic one.and a up graded muffler with a expansion chamber.dual handbrakes are nice too.expect to haft to work on a bike from time to time as they need upkeep.
Yes. saving that money is their game. Nothing to say they put it together correct. Most are fine. I've seen some loose head bolts/ studs / nuts, bad head gaskets and poor porting on most all. You usually get an OK running engine. OK. Not good
@@HughesMotorized And when I watch your video on about inspecting your engine like using lock tight on the engine studs and once my ned head gaskets come I'm going to take the engine apart just the top half and I'm going to inspect everything make sure that the piston in on the correct way and make sure the ports are clean and free of any burs. And I'm going to file down the piston skirt. At the start, I was going to take apart the engine because I was scared that I didn't know how to put it back together but now I know how to do it. thanks for the videos
Sir, great videos. I’m new to this motorized bicycles and I’ve been watching your videos a lot. I can say that they are very descriptive, informative and most important no language barrier anyone can understand. I would like to ask which would be a good or decent bike that won’t break the bank that I can use for one of these kits? Thank you
My name is Ashley I got a beach cruiser huffy 26in wheels and I was just wonder if you know what engine be good to put in my bicycle I hope you can help me and my brother and my father do like your channel we cannot wait to see you are videos thank you
I have a black 80cc stroke engine kit but I think it’s a China but idk and it works pretty good it’s insalely fast I’ve went over 35mph but my engine is super loud and rattley any reason why it’s doing that ?
Here's some tips for you 02 Highlander oxygen sensor gasket the exhaust it matches for the exhaust pipe and exhaust port and all the new jugs he gasket is a metal gasket and they works great it's a last chance of a gasket failure or leaking there about 5 bucks to local auto parts store you will have to in largest bolt hole just a little on the gasket blot go through gasket on one side only its does work
Yeah well I have purchased 5 kits from a vender in Pa. that advertises a balanced crank and guess what only one out of the lot had a little vibration going on down there so I would say they are at least paying attention to the details during the assembly process which is important
Hey I’m new to this but I definitely wanna get my moneys worth my dad is a mechanic (well he’s a jack if all trades but he knows his stuff) and I’m just a 17 year old guy that likes to ride bikes and wants to learn a new skill and I have 0 idea on what kit to buy from my understanding no matter what kit you get it’s gonna have problems the most important part is to make sure the engine is good. So any recommendations on what kits I should get? I looked at the links but got confused lol. I will say I have plenty of tools and work space for this project and I’m no stranger to this area I have a general understanding of everything I feel. Also from what I’ve heard it takes a lot of maintenance for these to work well and to stay working well. And one last thing my price range is $150-$250 I really don’t wanna spend $250 but Ik some things are worth putting the money into but if I could get a good kit for $180-$200 I’d be happy
Hey brother enjoyed your video I just subscribed to your channel...I've been a auto and diesel mechanic for 35 yrs and built race motors and drag raced all my life but I'm new to this little bicycle motor lol ...I've got a I guess is a Chinese 66-80cc engine... tell my if a bike Berry head will fit my engine or do you sell a head and carb I can put on it
The heads are interchangeable on all of the 66cc. They're all 66cc. Chinese call them 80cc but they measure different. Stock carb is fine unless you get into porting and a good expansion chamber. look into jetting and plug chop. That will help a lot
@@HughesMotorized can you give me a link to good engines / kits? www.californiamotorbikes.com/ Do they have good balanced kits? Pk80? Wildcat? How about Bikeberry? What’s the best kit under 400$ (Engine I could buy separate , then kit)
@@ZampostOk Some are better than others. Most are simply luck. If anyone is telling you a motor has been precision balanced for less than $300, they are lying
So these manufacturers seem to have a disclaimer;for racing only,not to be used on off roads or hwys.Will I get a ticket if I put one of these 2 stroke engines on my bike.? I live in California.
you did a good job on that video......I love this hobby but that cheap engine don't hold up and constantly needs work my head keeps warping even torque down right they r stock so maybe i need some cnc billet
Hi, this from my new ride. The fuel filter on the fuel line came apart as I was riding. Never seen that in 55 years of working on motors. So something to check on Your bikes everyone. If it can happen, bwwahhhaa.
I cant find any kits on ebay directly from China. Maybe I'm searching incorrectly. Anyone have a link to an ad or site from China. I live overseas and only China ships stuff for cheap.
Cr machine motors are out of stock, and arrow motor is out of my budget. I don’t really want to make adjustments to a cheap Chinese motor as I really don’t want to break something, you know any other good motors that would be reliable?
Bt100 $250 (bbr 80/100 and the anbull bt100 on amazon) those r the best damn engines I’ve had yet im not 100% on longevity but the first one I made is a yr old and still kicking
I have never liked that type of tensioner, it's uglier than a mud-fence, but maybe if somebody would chrome-plate some of these, and put some on eBay at a reasonable price, I might get a couple of them for my 4-stroke bikes, to have something different on a couple of them, plus I really want a nicer tensioner for those bikes, and since they don't make one of those spring-tensioners that attach to the engine of a 4-stroke, if I don't find a decent one for sale, I'll probably end-up fabricating my own tensioner for those bikes, thanks for sharing.
Really not much need to do anything to the 4 stroker other than slap it on a bike and go. Here;s a vid I did on the chian drive one: ua-cam.com/video/QCxYjYxap_A/v-deo.html HOWEVER.. coming up will be doing a 97cc Lifan build. There will be some mods on that. Stay tuned
Thanks so much for the info! i was going to buy a bike kit from Zoombicycles and was wondering if you knew anything about them or honestly just had any suggestions for what kit i should get. (its going to be my first one) i want to get a 80 cc or 100 cc motor so please let me know what you recommend!
A 3-4 hp reed motor Keep the stock pipe So it’s quiet. A 44-44T sprocket should get you ~25-30mph & you won’t have to pedal. Not a 1.5-2hp eBay kit. Matt from bmw is supposed to be pretty good
omg today i tried to fit a new 80cc cylinder to my 50cc 2stroke engine. the piston itself and the cylinder skirt did not fit into the case! why? why is my case hole so small?
I know I know people talk a lot of smake about the BBR I have the stage 4 and it's got 900 kilometers and still running as good as the day I got it just my experience
looking at bikeberry stage 4 kit and a few other things to put on a Scwhinn OCC. Im hearing shitty and non shitty review about BBR tuning but not familiar with any other companys and would rather stay away from ebay
Why does everyone only go to Amazon they don't offer PayPal or afterpay they just want your card details. Ebay you can't just buy the engine this is bullshit.
Trying to find a rear tire that is skinny and extra large I think 29” with a reverse pedal break and disc break option on it. Do I need to have one custom built?
I'm running two different engines. One is a Run Well and the other is a ZEDA engine. Both are ported, balanced cranks, Tuned pipes, High Compression heads, Big Box Racing Reeds, Hotter Plugs, longer Intake Tube, and finally a Richer Main Carburetor Jet. Fuel Mix is 50 to 1, Stelle Chainsaw Full Synthetic Oil and 92 octane gasoline. Stock these engines put out about 2.2 Horsepower. With my Mods and if I ran the math correctly, I'm getting about 9.2865 Horsepower. The bike is an Aluminum Flat Frame 26 in. Beach Cruiser, running 2.25 wide Tires at 50 lbs. This thing can really get up and go, climbs the hills like a goat. What a hobby. Thanks for the info.
Awesome Bro
Pro tip: with the proper piston that matches the bottom end, all the cylinders have similar enough port timing to be inter-changeable. I was hard up and needed an emergency jug replacement and discovered my cylinder from an older "type A" piston engine worked with my Zeda80, which has the longer connecting rod, and requires the type "B" style piston or as Amazon usually calls them, "high hole" piston. Only thing is, the stud spacing on the intake port- it's either 32mm or 40mm and youd have to get a different intake pipe if you changed cylinders and ended up with a different measurement, but I assure you the cylinders will work in every aspect but that one.
I used your videos to build my "Beast" with ZERO EXPERIENCE.
The manual that came with it was pretty much USELESS.
I was totally in the DARK as to -- HOW -- I was going to assemble this thing.
I looked at LOTS of videos and was SO LOST as to what needed to be done.
THEN --- I found your video tutorials.
WOW.
These let me know -- EVERYTHING I NEEDED TO KNOW in how
to build one of these little bone shakers.
Your videos couldn't be any more SIMPLISTIC and --- UNDERSTANDABLE.
After I built mine, I had various minor glitches that wasn't anything too hard to figure out.
My little Beast probably is running about 35 plus MPH straight as is stock.
Very rarely do I get it at full throttle as I come up too fast onto the stop signs.
After I break it in good i plan on adding a couple of high performance parts.
I do not plan to bore it out or anything drastic, just add maybe a Boost Bottle and a Combustion Chamber muffler.
I don't think I have enough room to add a large carbureator.
I may or may not have enough room for a high compression head, but I'm not really sure.
I do know about the Jack Shifter, but I really don't wish to run it at about 65 to 75 MPH after utilizing all 21 gears.
It's a MOUNTAIN BIKE for God's sake.
My little "Beast" really flies as it is and I'm really IMPRESSED with it.
I have had a Honda CB200, a Honda PA50 Moped, and my favorite - the Tomos 2 speed automatic Silver Bullet moped.
But NEVER something like THIS LITTLE THING.
And --- YES --- I thoroughly believe in helmets and NEVER ride without one, unless I am using a Motor less Bike.
You can ask Gary aBusey about that one.
Ha ha --- ha -ha.
Glad to help
If you all want to know how to do it right the first time, listen to this guy,he knows exactly what he is talking about
thanks!
This is something just for fun I have a dirt bike if I want to go fast and a gsx 1000 80 bucks is enough to ride around my neighborhood
I love this channel so far
its totaly home made but the personality is great and the camera work isnt shit
Goot job
Kipper Klank it’s you tube it should be home made jeeezus What the heck do you expect ...... you got a channel?
@@nadronnocojr I've seen some really poorly executed and produced videos with like no effort put into even the simplest editing, or bother to check if you can understand the audio. lol
I really appreciate your videos in regards to the motor itself I found a decent motor kit for about $150 everything except for the motor and the crankshaft is made relatively cheap but for 150 bucks yaheeda has the best motor kits for the price in my opinion
I must have gotten lucky because my little 50cc runs like a scalded dog lol it was a gift because he bought the cheapest kit he could find and couldn't get it to work correctly, I opened up the intake and took out the center of the exaust, tightened the sparkplug down, tightened the carb down because he had it loose... put some 40:1 in it, zoomin now...
Any tips on how I can get more rpm?
a motor is basically a pump. Increase flow and increase rpms. Clean ports, good pipe and a balanced motor will increase rpms and power. First clean ports, then a good expansion chamber and a properly jetted carb will help
@@HughesMotorized I got a pipe but I think I need some port matching
take out the governor
Thanks for this brief intro to motor prep. It was helpful. Wish I would have did more research before I ordered the 97 dollar 2 stroke. Luckily I havent put it on yet, so cleaning up burrs will be less dirty lol. Im just worried about touque for hills. I do have a 44 tooth. think i might bump it up a bit though. Bought my motor and its been sitting in the box for a couple months lol. Lazyness I guess.
Do it u will love it and wish u set it up sooner i did the same thing.
I’ve had the chain tensioner go into the spokes going 32 and is was not fun. It basically just tore up the back wheel in the worst way possible. But I didn’t crash! Thank god. I skidded for about 40 feet
😂🤣🤭
they make a different tensioner now that's a lot better
The arch chain tensioner is the best thing since sliced bread. Great job as usual :)
Amen, I'm too lazy to not use a tensioner and find the arch one awesome. I'll sometimes weld one onto the frame as well
Will a 47 millimeter piston fit in a 50 cc motor or do I have to change the cylinder to.
Eugene I have a Genisis Onex 29 inch large down tube what inexpensive engine that will fit directly??
You need a wide mount adapter
the 420 chainlink size works very well for these kits
its 420 tomorrow
How can the bassum rise to the pressure stroke even though it is one piston, not two?
Thanks for videos gizza here from england, I've just got YD 100cc engine will my 80cc carburetor and my coil fit on my new engine, can you let me know please
Should work no problem.
I like the runwell motor with upgraded bolts .the crank is tight and the only problem I see is the clutch bearing needs upgraded to a better bearing then the cheap one that is stock.the stock carb is fine but the air filter needs more flow then the stock one lets it get.i use a skateboard wheel on my chain tensioner stock bracket to replace the plastic one.and a up graded muffler with a expansion chamber.dual handbrakes are nice too.expect to haft to work on a bike from time to time as they need upkeep.
My engine came fully installed like the engine was put together already do some kits only put together half of the engine and you do the rest?
Yes. saving that money is their game. Nothing to say they put it together correct. Most are fine. I've seen some loose head bolts/ studs / nuts, bad head gaskets and poor porting on most all. You usually get an OK running engine. OK. Not good
@@HughesMotorized And when I watch your video on about inspecting your engine like using lock tight on the engine studs and once my ned head gaskets come I'm going to take the engine apart just the top half and I'm going to inspect everything make sure that the piston in on the correct way and make sure the ports are clean and free of any burs. And I'm going to file down the piston skirt. At the start, I was going to take apart the engine because I was scared that I didn't know how to put it back together but now I know how to do it. thanks for the videos
Sir, great videos. I’m new to this motorized bicycles and I’ve been watching your videos a lot. I can say that they are very descriptive, informative and most important no language barrier anyone can understand. I would like to ask which would be a good or decent bike that won’t break the bank that I can use for one of these kits? Thank you
huffy cranbrock is a good optcion iv had no prob four years now year round
Ok thank you very much keep up the good videos I have learned alot from your videos.thank you again Robert from Illinois
My name is Ashley I got a beach cruiser huffy 26in wheels and I was just wonder if you know what engine be good to put in my bicycle I hope you can help me and my brother and my father do like your channel we cannot wait to see you are videos thank you
here's a link for a good deal on a 2 stroke kit >> ebay.to/2utCvrX
I have a black 80cc stroke engine kit but I think it’s a China but idk and it works pretty good it’s insalely fast I’ve went over 35mph but my engine is super loud and rattley any reason why it’s doing that ?
Piston could be hitting head. I've had some rattle at first then the engine quited down after breakin
Here's some tips for you 02 Highlander oxygen sensor gasket the exhaust it matches for the exhaust pipe and exhaust port and all the new jugs he gasket is a metal gasket and they works great it's a last chance of a gasket failure or leaking there about 5 bucks to local auto parts store you will have to in largest bolt hole just a little on the gasket blot go through gasket on one side only its does work
Thats what I use.🏁👍👍
What about zeda?
Good luck finding one in stock
i live in den what jet can i use for 15,000 altitude?
Thank you for your videos. As a beginner to this hobby I appreciate the help and information on your channel. 🙌
Glad to help
Hey can you help me pick out a moter kit cheap to
Here's a decent one: ebay.to/2ROy4kh
Maybe a vid for the best 4 stroke kit?
I think zeda is up there at the top for performance engines.
I suggest a Google search on them. There are 2 "Zedas" out there. The importer and Bianchi's outfit.
I would recomend the samger 100cc engines.
Pls review bt80 engine kit
Where could you get a PETCOCK for that same silver engine
Do you sell a good 100cc engine kit for my 29er bicycle?
Here's one: ebay.us/VYLUAL might consider a bigger sprocket w/ 29" wheels like a 50 tooth one
Yeah well I have purchased 5 kits from a vender in Pa. that advertises a balanced crank and guess what only one out of the lot had a little vibration going on down there so I would say they are at least paying attention to the details during the assembly process which is important
Some are built better than others. Still a crap shoot unless you get Fred Chelminski of C&R machine to do it right. His motor kits start at $300ish
Where can I buy a good 2 stroke engine?
Here's a decent one. Always inspect a new kit and look for issues. ebay.to/2WUCoRN
Hughes Motorized thank you so much man do you know if there are any good black ones
@@unknownfilms9905 spray paint it. The powder coat they apply to make them black is horrible and causes problems
Uncle.... How to refill the engine 2T oil..... I don't know....
4 stroke? Remove dipstick and fill to line.
2 stroke? add 3.5oz oil to gallon of gal and put in gas tank
Thanks for thw advice I'll look at it when it comes in
Hey I’m new to this but I definitely wanna get my moneys worth my dad is a mechanic (well he’s a jack if all trades but he knows his stuff) and I’m just a 17 year old guy that likes to ride bikes and wants to learn a new skill and I have 0 idea on what kit to buy from my understanding no matter what kit you get it’s gonna have problems the most important part is to make sure the engine is good. So any recommendations on what kits I should get? I looked at the links but got confused lol. I will say I have plenty of tools and work space for this project and I’m no stranger to this area I have a general understanding of everything I feel. Also from what I’ve heard it takes a lot of maintenance for these to work well and to stay working well. And one last thing my price range is $150-$250 I really don’t wanna spend $250 but Ik some things are worth putting the money into but if I could get a good kit for $180-$200 I’d be happy
Hey brother enjoyed your video I just subscribed to your channel...I've been a auto and diesel mechanic for 35 yrs and built race motors and drag raced all my life but I'm new to this little bicycle motor lol ...I've got a I guess is a Chinese 66-80cc engine... tell my if a bike Berry head will fit my engine or do you sell a head and carb I can put on it
The heads are interchangeable on all of the 66cc. They're all 66cc. Chinese call them 80cc but they measure different. Stock carb is fine unless you get into porting and a good expansion chamber. look into jetting and plug chop. That will help a lot
@@HughesMotorized ok thanks alot brother
Yo how about zeda engines? Are they any good?
Decent. I suggest you google any seller and see if they are reputable
@@HughesMotorized can you give me a link to good engines / kits?
www.californiamotorbikes.com/
Do they have good balanced kits? Pk80? Wildcat?
How about Bikeberry? What’s the best kit under 400$ (Engine I could buy separate , then kit)
@@ZampostOk Best in the business : crmachine.com/shop?olsPage=t%2Fmotorized-bicycle-race-engines&page=2
@@ZampostOk Some are better than others. Most are simply luck. If anyone is telling you a motor has been precision balanced for less than $300, they are lying
@@HughesMotorized anything cheaper than that lol?
Wear can I buy a quality 2 stroke engine with reeds
Here's a decent one: ebay.to/2uA8Pde
James Volpe Ken Hinson. Check Facebook. There’s another dude making Athena hybrids.
Where can I buy a good 80cc motor best good quality?
I just brought a 80cc/100cc motor and it be jumping when I start it up ,what the problem?
Can you move motor by hand? If so there's your problem. motor has to be solidly mounted. Zero flex. Zero movement
Where do i get gaskets?
amzn.to/2JAPRKD
So these manufacturers seem to have a disclaimer;for racing only,not to be used on off roads or hwys.Will I get a ticket if I put one of these 2 stroke engines on my bike.?
I live in California.
I know one can get them licensed in Cali but I'm not sure if any issues w/o a license. Ask on a FB or Reddit page
@@HughesMotorized I did,it said up to 125cc a motorized bike is OK.But why the disclaimer from every motor build company.?
@@tr7b410 that way if you get hurt riding one or ran over the seller isn't likely to be sued
Another good way to gain some power for. Cheap is notch the piston for the Intake
you did a good job on that video......I love this hobby but that cheap engine don't hold up and constantly needs work my head keeps warping even torque down right they r stock so maybe i need some cnc billet
Might consider a 4 stroke. ebay.to/2Kshwe0 . Fewer issues
Hi, this from my new ride. The fuel filter on the fuel line came apart as I was riding. Never seen that in 55 years of working on motors. So something to check on Your bikes everyone. If it can happen, bwwahhhaa.
I had one of the brass petcocks come apart and spill gas all over my hot cylinder head. Exciting there for awhile but no boom. Ride on & enjoy!
@@HughesMotorized Although they can be shined up really well, they ain't worth crap. Shame really.
What's your opinion of the 2 stroke BT80 electric start motors?
I have yet to build one . I figure the extra components might be sketchy and I'd have issues w/ replacement parts so I've avoided them
Great videos, helpfull, keep the good job thanks, say hello from ppanama republic.
Thank you! Enjoy
Is that the Pederast from the Big Lebowski on his shirt?
Yeah well you know, that's just like your opinion man
I cant find any kits on ebay directly from China. Maybe I'm searching incorrectly. Anyone have a link to an ad or site from China. I live overseas and only China ships stuff for cheap.
Maybe check alibaba
Everything on wish is from China
where can i get that shirt? love it and love all your videos
come on thats shirt is money
Zeda engine are sold several different companies Apollo racing,80cc bike,go max,and zeda motorsports
I have a zeta and its my frist bike and love it
That intro surprised me
Cr machine motors are out of stock, and arrow motor is out of my budget. I don’t really want to make adjustments to a cheap Chinese motor as I really don’t want to break something, you know any other good motors that would be reliable?
Bt100 $250 (bbr 80/100 and the anbull bt100 on amazon) those r the best damn engines I’ve had yet im not 100% on longevity but the first one I made is a yr old and still kicking
I've got the anbull BT100 kit. Does 35 easy with a 36 tooth sprocket. I don't even have a chain on the pedals, clutch is sufficient to go from a stop.
I have never liked that type of tensioner, it's uglier than a mud-fence, but maybe if somebody would chrome-plate some of these, and put some on eBay at a reasonable price, I might get a couple of them for my 4-stroke bikes, to have something different on a couple of them, plus I really want a nicer tensioner for those bikes, and since they don't make one of those spring-tensioners that attach to the engine of a 4-stroke, if I don't find a decent one for sale, I'll probably end-up fabricating my own tensioner for those bikes, thanks for sharing.
Can you do one on 4 storke
Really not much need to do anything to the 4 stroker other than slap it on a bike and go.
Here;s a vid I did on the chian drive one: ua-cam.com/video/QCxYjYxap_A/v-deo.html
HOWEVER.. coming up will be doing a 97cc Lifan build. There will be some mods on that. Stay tuned
Nicely done sir. Some solid info you pass along. Thank you.
Glad it was helpful!
Thanks so much for the info! i was going to buy a bike kit from Zoombicycles and was wondering if you knew anything about them or honestly just had any suggestions for what kit i should get. (its going to be my first one) i want to get a 80 cc or 100 cc motor so please let me know what you recommend!
It's hard to find them at a decent price lately. They are all pretty much the same. You have to sort thru and make them run good is my experience
THANK YOU FOR SHARING
A 3-4 hp reed motor
Keep the stock pipe So it’s quiet. A 44-44T sprocket should get you ~25-30mph & you won’t have to pedal.
Not a 1.5-2hp eBay kit.
Matt from bmw is supposed to be pretty good
Lol a 3-4 hp engine shod be able to go faster than 30 my cheap 49cc can go 30 😂😎
Real time 30. Not a tuck your wiener 30 on a California road
How about Skyhawk motor
all brands are pretty much hit or miss. ThatsDax has some of the best out there however one should sort thru all 2 stroke motors
I'm thinking of sanding down my head to get more compression.
I like your vids man, keep it up!
Glad you like them! More to come
Thanks so much for the informative videos, must say i have learned a whole bunch of good stuff.
Regards
ROB
Awesome, thank you!
omg today i tried to fit a new 80cc cylinder to my 50cc 2stroke engine.
the piston itself and the cylinder skirt did not fit into the case! why? why is my case hole so small?
I enjoyed this very informative video. You have a new subscriber. 😊👍
Welcome aboard! Thanks!
I know I know people talk a lot of smake about the BBR I have the stage 4 and it's got 900 kilometers and still running as good as the day I got it just my experience
Dude, this is some good info.
Glad you think so!
How much this motor ???
$100. You cannot beat the prices on here: ebay.to/3bpopJ8
i got a 80 dollar 80cc kit and it outperformed my friend's 220 dollar 100cc kit...
I can see a scratch near the top of the cylinder
Thx for this!
Great info wow.
Glad it was helpful!
Epic intro
looking at bikeberry stage 4 kit and a few other things to put on a Scwhinn OCC. Im hearing shitty and non shitty review about BBR tuning but not familiar with any other companys and would rather stay away from ebay
Bikeberry is decent, you still need to inspect the cylinder, cylinder studs, gaskets, head and the like.
Every time I remove nuts here at my shop they always seem to come back
WHY ARE YOU YELLING AT ME! IM RIGHT IN FRONT OF YOU!
I'M NOT AWARE THAT I WAS YELLING !!!
@@HughesMotorized Lol Im just pulling your leg. the information was loud and clear ;)
Zeda is #1
Injan pric
Think you should add zeda motorsports engine to your list
EXCELLENT
Hi
What if you don’t have a Twork wrench
"Yeah Fuckin Jesus..!" ( 8Yr Olds Dude..!)
Awesome
Why does everyone only go to Amazon they don't offer PayPal or afterpay they just want your card details.
Ebay you can't just buy the engine this is bullshit.
Tell me worst one, I want the buy the worst one!! Not the best one... 😜
o yea mane i ordered one from banggood i wish it comes with no trouble pls god plss
Update!!!
@@jamescarlin569 i received it broken. Fixed it and installed it, now i breaking in. It is good tho.
How is it now? And what was broken
LIKE DO BRAZIL
Fuck it, ill just walk.
You wont believe me, but I bought a kit pff wish for $0.50😂😂
I believe you I almost did the same
did it actually come?
Did it come?
Did it come?
No it didn't
I just bought one off eBay for $16.99 waiting to see what I get now lol
Hopefully get a refund when it doesn't arrive
@@HughesMotorized 😆😆😆
xx love 💗 c
burrrrrrrs
Pakistan Price👉 WhatsApp
bla bla bla...