Hi. I’m back to say a huge thank you for helping me with immo off on a MED9.1.1 ÉCU from my 2010 Audi Q7 4.2FSI. It was not easy but we made it. To make it work we needed to write the eeprom, flash and MPC. Without that the engine couldn’t start. Thank you
Hi thankyou .. Dont forget to like and Subscribe..... This method uses information from flash and eeprom to make modified new eeprom. 100% guaranteed to start with no hard codes or safe message on dash .. power windows and accessories work fine... with wrong immo off for some reason accessories won't work in car... Goodluck
Hi please thanks for your knowledge sharing spirit , i would like you if you can help, me with dump immo off bin file for both flash and eeprom for my vw jetta fsi 2.0 model 2007, i do have error immobiizer adjustment, so on my PCMFlash module 71 it does not appear on my list?
I have a Global A ECM for 2013 buick verano, just learned of this. Do you offer private requests? Dealer won't flash Vin or clone, and can't find a shop near me
Hello, am having safe shown on dash of VW Q7 4L. Original ECU was fried and the owner got a second hand ECU the car worked ok for a while but now it cranks no start, no spark. Do you think wrong immo file would do that? Thanks..
If car ran with replacement ECM before without any issues then there should be a problem somewhere else... Check for water coming into car because maybe bad module killing communication... You need to scan first and see what codes all the modules are reporting..... Also if ECM was opened to clone then maybe water got into ECM, maybe they did not seal ECM properly.. Does the car turn on for a couple of seconds then shut off???
With bad communication ECM should still start car for at least 2 seconds then shut off... Scan and check all codes, if you can see live data in ECM check RPM data pid to see if crank sensor is working
@@temejumbo9794 go to live data in ecm and view Rpm pid ... Hold in crank position to keep starter active while viewing live data you should be able to see rpm 200rpm to 600rpm even if car does not start... If you have rpm In love data while engine is cranking then there is another problem (maybe relay that powers coils is not being activated by ecm..... If I where you I would get another used ECM install and see if car starts for a couple a seconds .. Good luck 👍
I need data to check, I remember doing either 9.1.1 or 9.1.2. I need data to check in software . ( ??? why do you want immo off??? ) ... Thanks my contact information is in my community page
Hi. I’m back to say a huge thank you for helping me with immo off on a MED9.1.1 ÉCU from my 2010 Audi Q7 4.2FSI. It was not easy but we made it. To make it work we needed to write the eeprom, flash and MPC. Without that the engine couldn’t start. Thank you
Glad I was able to help... Enjoy 😉
Hello brother can you help me with the same ? I have the read files from the eeprom and flash
Hi , excellent video,
Question you only write eeprom new file from vvdi2 ,( NO FLASH), right??
Hi thankyou .. Dont forget to like and Subscribe..... This method uses information from flash and eeprom to make modified new eeprom. 100% guaranteed to start with no hard codes or safe message on dash .. power windows and accessories work fine... with wrong immo off for some reason accessories won't work in car... Goodluck
Hi please thanks for your knowledge sharing spirit , i would like you if you can help, me with dump immo off bin file for both flash and eeprom for my vw jetta fsi 2.0 model 2007, i do have error immobiizer adjustment, so on my PCMFlash module 71 it does not appear on my list?
Thanks Boss..
I have a Global A ECM for 2013 buick verano, just learned of this. Do you offer private requests? Dealer won't flash Vin or clone, and can't find a shop near me
You can contact me Keys24@yahoo.com
I'm currently on vacation but at the end of the month I can do no problem. EMAIL me picture of your bcm.
Hello, am having safe shown on dash of VW Q7 4L. Original ECU was fried and the owner got a second hand ECU the car worked ok for a while but now it cranks no start, no spark. Do you think wrong immo file would do that?
Thanks..
If car ran with replacement ECM before without any issues then there should be a problem somewhere else... Check for water coming into car because maybe bad module killing communication... You need to scan first and see what codes all the modules are reporting.....
Also if ECM was opened to clone then maybe water got into ECM, maybe they did not seal ECM properly..
Does the car turn on for a couple of seconds then shut off???
With bad communication ECM should still start car for at least 2 seconds then shut off... Scan and check all codes, if you can see live data in ECM check RPM data pid to see if crank sensor is working
Yes there was water on the second ECU, someone tried to fix it but when it starts for some minutes then it stops. Would only crank but no start.
The time the car starts is not enough to run a live scan. Though I have read in some forums that a faulty crank shaft sensor might be the problem.
@@temejumbo9794 go to live data in ecm and view Rpm pid ... Hold in crank position to keep starter active while viewing live data you should be able to see rpm 200rpm to 600rpm even if car does not start... If you have rpm In love data while engine is cranking then there is another problem (maybe relay that powers coils is not being activated by ecm..... If I where you I would get another used ECM install and see if car starts for a couple a seconds .. Good luck 👍
Please can you help me do immo off on a similar ecu me 9.1? Thanks
Did you do already if not contact me on my email listed on my community page..
Please did you write back the flash. Thanks
Yes Eeprom and flash was modified...
@@Autokey_Security_Services can you upload the files mate please
@@safoolm9421 I can send thru whatsapp or email.. I will need your original non modified eeprom and flash (keys24@yahoo.com)
Can i open the vvdi2 program without vvdi2 device,i have ktag device and i read eeprom only need to write immo off
No must have vvdi 2 to do anything with software.
@@Autokey_Security_Services oh okay,so there is no other program that can disable immo off,if i have already read the flash and eeprom?
@@Benko_DieseL send me flash and eeprom to my email or whatsapp ... I look at it for you
@@Autokey_Security_Services I dont,am just asking because my friend wants to sell me ktag,so i wanted to do it myself
Can you just do that with the Autel 508?
Not immo off. Have not seen on any menu on 508 only read immo data .. Even VVDI 2 does not do me9.1 immo off thru obd... I did not check with Abrites
Hi. Can i send med9.1 rs3 ecu for u to off immo?
I am currently on vacation. In 2 weeks no problem.. Thanks
Have you maked the immo off on rs3 9.1.2 ?
I need data to check, I remember doing either 9.1.1 or 9.1.2. I need data to check in software . ( ??? why do you want immo off??? ) ... Thanks my contact information is in my community page