Top 5 must that you need to know before
Вставка
- Опубліковано 19 сер 2024
- Top five things you need to know about a 3 axle alignment. What happens when you have to much caster split and what you need to look for with part cks and more
- Авто та транспорт
Great job on explaining the process n please give bob a raise you have really been working him
When you pass on who gonna fix this shit????? Not these cowboys we got now!! They cry when mommy forgets their fruit roll ups! You are one of a kind sir!!! Love it!!
I've been asking basically the same question across all the trades. I do collision repair but on regular cars and trucks. The last icar training I went to there was only one guy there younger than me. I'm in my early 40's and one of the youngest guys in the industry. The old guys are already calling us parts changers instead of real body men. They're repairing stuff that should be replaced but that's a different story for a different day. These trades have to change soon or there's not going to be anyone to do the work. Pay needs to increase significantly to start with. How about working conditions? Anti fatigue flooring and air conditioning would be a good start. Benefits. Not a single independent shop I worked at offered any sort of benefits.
@@aaadamt964 Well, unfortunately, "parts changers" is part of today's society since we've become a throw away society. A slight "ding", replace it, instead of actually fixing it, then you have plastic body parts... yea, part changers. Sorry but it is what it is. Vehicles 30-40 yrs ago, made way better than today's junk, again, I'm old school.
Not even a Diesel Mechanic, but I am a Driver who grew up in an automotive junk yard, and I can't ever pass up one of your videos brother.
You do a good job, thank you for making our lives easier.
This is raw expertise. Now I just need to figure out how to change my porta power from that hand pump to pneumatic
this video told me a lot about the front axle and tires of a modern truck
When it comes to these types of repairs, you're the best, always learning and remembering what my old vo-tec teacher taught me. Cheers :)
shutting down the haters with knowledge,🎉
Yep, there's no replacement for boots on the ground experience.
I watch because I own a couple trucks and love to learn specifics of frames and wheel end/ suspension issues
The stop right before the rant was perfect 😂😂
Bendon, i will never need to know about a 3 axle alignment. I hate cars. You're just an interesting dude.
I have been reusing U bolts for 40 years without an issue providing they are not damaged, if they are sprung a little just put a clamp on them to get them back in the axle, Living in a small town where parts aren't readily available and usually days away for delivery you make do with what you have.
His editing is great. I enjoyed and learned a lot
Dude knows his stuff
been turning wrenches my whole life and currently taking a class to work on those kind of trucks and I wish I could come work with you and learn.
The experience is amazing!!!! You only get this good by hard contact work!!!!!
It's a pleasure watching a knowledgeable professional work Devin.
Best Wishes to You and Your Family.
I never cease to be amazed at your knowledge. You have my respect!
Thanks Devin 😊😀😎 Now For Part 2 👍🏼👍🏼👍🏼👍🏼
Excellent Video
An experienced technician is worth at least fifty percent of the labour charged.
Im telling my friends about your channel.
Yes, both of them.
I may have one, myself.
You don’t pay for my time you pay for my experience .
$80 for a quickie $120 for a whole half an hour but the memories last forever..... 😮
I love every one of your videos!!!
It’s always a treat to see your videos whether it is a shop vid or one with your family in it. You have a very nice family that is close and supportive of each other.
You and Bob are very intelligent and have a great sense of humour, something a lot of people either don’t have or decided to shove it up their butt.
Your information is accurate and on point.
Keep up the good work!!!
What I'm seein' is a financial professional/business owner at work! I couldn't imagine what it took to get that kind of operation off the ground financially and what kind cash flow coming in the door "daily". You must have employees, so all the expenses that go with that are astronomical. You've some amazing tooling there and the skills to operate them. I can only hope you have a son or family member to pass on what you built. What you have is rare in today's environment. Mike Rowe should interview you. I used to be a construction mechanic so most of my truck work was layin' on piece of plywood over the mud/rocks to tighten the front axle ubolts with 40" long Snapon 3/4" drive ratchet. So, I recognized some of the components your working on.
He works for the shop.
you are a breath of fresh air in a clusterphuk jam packed of painfull "tradie" content. im a heavy fabricator engineer/boilermaker building custom truck and heavy vehicle bodys for things farm or forestry units and fleets of lil service trucks.. ive seen it all as it seem you have too 😅 i feel the pain in having to explain or deal with previous halfpie workmanship ❤
No wonder my hubs were always leaking, they were overfilling them. Never crossed my mind that the mechanics were the problem. 😂😂😂
Mr Bendin, thanks for the pure gold. I use spring seat when I'm shimming my steers.
So many people don't check for worn parts before alignments it's crazy, not a big rig guy here, just do automotive alignments at the shop I work at. It's a shame but a ton of guys out there aren't checking everything over properly before beginning alignment. Especially be weary of chain tire shops. Typically they're not checking suspension parts adjusting proper tire pressure before beginning. And alott of places they're just doing a Toe and Go, so they just adjust toe regardless of it it's needed, don't touch anything else, but they do the toe because then they changed the alignment and thus can justify charging the alignment.
I've had the opposite experience at several chain shops. Get a vehicle, completely rebuild front end at home. Take it in to get alignment only for them to call me saying i need a bunch of parts. I always ask for quote, and ask store manager to point out bad parts cause "I'm sure they should still be good". When he starts pointing and realizes everything is NEW. I respond i was thought they'd be good i just installed them yesterday, that's why i need an alignment. Usually about then is when he notices my snap-on, hat, shirt, hoodie or jacket if it's cold.... Keyring and i always leave Snap-on 1/2" torque wrench on passenger seat so any mechanic paying attention is forewarned not to be stupid.
Love the info Bendon. I do HVAC in AZ and the perspectives you share is very enlightening for a thick skull like mine lol can’t hurt to have more knowledge than I may ever get to use haha
I used to do this everyday but the boss wouldn't give raises or pay overtime so I left. Now he has to send it out and pay more. 😂
Funny how that works ant it, I don't got sucked in to doing all the mechanical work on my bosses trucks I'm supposed to just be cutting trees
Keep up the great work. I love your videos and how you react to the armchair mechanics. Just a FYI, I recieved Bob, pretaped, and he is now happy on the West Coast of Canada now.
Interesting stuff. I never really experienced alignment stuff when I was an apprentice diesel mechanic, we did straighten out some tipping trailers that had turned over on landfills using the Winches on my company's tow truck.
i love your content man! ive been wrenchin on trucks for a couple years, but nothing in depth (loves) and ive learned a lot from your videos!
Awesome show Devin keep it up 🍻
With the tighter turning tractors. You can really tell who has a hard time in tight places. I've seen steer tires with the outside edge bald as can be with 3/8 inch of groove left on 3/4 of the tire. Especially up here in the North East with short dock space and 53 foot trailers.
Makes one miss the old "cab overs" and their turning radius.
In the south it's better to have a little extra castor. The high pitched roads for rain drainage will often cause factory recommendations to drift.
Drag cars use ridiculous castor settings. 😂🤣
God bless you and your family as hard as you work 💪
❤❤😂😂 very educational... Love it
Factory defects?!?!?! There NO such thing!!!!
welds missed its place by a centimeter and not one noticed not even the quality check. the forklift dude had to stop it.😆
Damn straight. Those are features.
No factory defects
Just defective factories XP
Lmao good to see it's not just Bethesda.
Lmao
Can't wait to see Devin in a body shop wet T-shirt calendar all twelve months.
That would be Funny.
@@dougobrien2840 😂
Do love a good gap!
Great video!
Top 5 must that you need to know before
Engrish
English, how to take a joke, how to be polite to customers, when to shut your mouth, tools and jacks are dangerous no screwing around.
Very different than car alignments !!
Great vids man you’re awesome stay safe and keep doin the great job that you do!
The operator's mantra for anything on the road or off the road that has moving Parts is securely mounted not cracked damaged or broken
Keep up the good work!!!!
Awesome job!!!! Thanks!
Fantastic my friend
I subscribed your channel not because I have endeavored to be a frame straightening God like you
but you know you’re an interesting character as well. however your audience should be geared strictly toward your line of work because as interesting as it is it would be over interesting for that crowd. you are very good at what you do. Please congratulations to your success and a good work performed rest well. You deserve a vacation come visit some time. BBQ fishing lake nearby good break. Love you, man. Bring family. See you soon.
I see a comedy tour in your future.....Bend it Boy...
No factory defects yet he's running a two hand hole wheel on the left side and a five-hand hold wheel on the right side
Go BOB!!! great video
I straightened the center link on an old Freighliner (they wouldn't buy a new one). Set the toe like that with a scribed line. That truck drove good. ❤ I could use some caster shims for my F450. Where could I get them easily?
Positive caster is a must for a car or truck that tracks in every little Crack.
It's called S.W.A.G. Scientific Wild Ass Guess.
Sure that's a Bendix steer assist with ZF stamped on the side? In combination with the VDRU (Detroit assurance or WABCO Ongaurd and Onside radars) collision mitigation system. In combination with the ABS, Engine and transmission ECM, and the electronic stability control system ESC. In that case the yaw rate sensor is tripped, setting a fault in the ABS requiring the steering angle sensor SAS to be calibrated and the end of line procedure conducted. 😊 also note make sure you dont have any J1939 CAN communication issues.
just what I was thinkin
You are Good Tec
Why can't you reuse, u bolts. Back in the late 70's we kinda used them again. We had a bearing go bad on the front-end, we had a spare front-end and just unbolted it and bolted the new one without changing the u-bolts was that bad. Nothing ever happened to the front-end
I've done that too, however, like head bolts they stretch when torqued, so it's recommended to replace.
Torque yield engineering. Must make everything disposable even though we are killing the planet and need to be green!
@@calvins1837 new ones stretch, they have to be retorqued after 500 miles, and again at 10000 miles, show me the manual that says they are one time use
@youtubeisawesome2487 if they are TTY or torque to yield, they need replaced. If a bolt is torqued past is limit, it won't 'spring' back when loosened. So the recommendation to replace is because you don't know unless a manufacturer specifies that a fastener was TTY or not, or whether someone before you over torqued a bolt. A shop will most always replace them, to save from having a come back. BTW hope you and everybody out there is having a great memorial day weekend.
@@calvins1837 Some bolts are able to be reused if they have not elongated beyond the manufactures parameter. Elongation can varie from bolt to bolt within a single set and job.
Litigation is probably the biggest risk. cheers,
Good Job
You the man👍🏼
What causes CHOPPIN,
I supervise 5 tree crews w/ bucket trucks . Everyone of my bucket trucks have " CHOPPIN " On the drive tires , how can I correct this issue
Bad suspension parts and bent wheels
Air pressures, alignments, driver habits, hitting curbs, kinda i. Your business, running retread tires, your casings? Or taking what the tire shop has laying around if the casing for the retread is cupped it will show on the retread in no time running real aggressive treads dont help just 15 years of fixing truck telling what to check
Technical term is cupping or scalloping. It's most often caused by weak shocks. The tire literally bounces when rotating. You're not talking a huge amount of "bounce". It's more so the uneven pressure being put on the tire as opposed to the tire actually hopping off the road surface. Other things CAN also cause cupping like worn suspension components. Once a tire is cupped you can NOT reverse the damage. But rotating the tires so they turn in the opposite direction AFTER fixing the suspension issue will stop it from getting worse.
@highpsiguy4085 cupping is not chopping
. -Cupping is smooth waves in the tire tread.
-Chopping, or "heel toe wear" is when the tread resembles a chop saw blade(circular saw blade), usually caused by mismatch pressures, or when one tire in the set has more tread than the other.
That zero toe makes sense from the factory.
Vehicle assist system. A gizmo attached to the steering box with wires going to the steering wheel. That will make the supply chain more efficient and the highways safer. Yes sir. I was hoping you were going to make fun of that clown world garbage.
So you don't understand it and make fun of it. All new stuff is garbage, you must use manual steering and mechanical brakes. I hear seat belts are stupid too, mess up your clothes and you would rather be thrown free in the accident you caused due to a lack of ASB, right?
Rock on like the info
stoked to have a gravy job for once or missing the challenge of something twisted ??
Caster wedges not camber wedges, ya can't....
Lmao
Just curious. At around 8:30, you were about to say something about camber but stopped yourself. You were going to say you can't adjust camber from that location on the vehicle, weren't you? Because if you did finish the sentence, you would have a bunch of people arguing with you. You're right, of course, but I just couldn't help but laugh.
caster affects camber
@@youtubeisawesome2487 Just about every alignment angle effects every other alignment angle, when you adjust it. However, that has absolutely nothing to do with what I was asking. Don't take this the wrong way, but if you read my post, you'll see I mentioned that my guess was he was trying to avoid arguments with other posters who don't have the same understanding as to how it all works. Posts just like yours are what I was referring to.
They all do affect each other but how would the forward or rearward tilt of the steering knuckle affect camber since camber is the inward or outward tilt of same knuckle. I see how his shim tilted the axle itself changing the caster angle but I'm not picturing it affect camber all that much.
@@keith6943 when you change caster it changes the tilt of the axle, the kingpin is not straight, camber is the angle the projects the spot the tire hits forward of the axle, loading the truck with weak springs can throw all the angles off, or those stupid air bag conversions you see everyone doing, the good thing is caster (steering wheel return when you let go of it) and camber are handling angles, toe is a wear angle, when caster is too high it darts (hard to hold straight) all manual steer gear box axles have caster of one so you dont fight the hard steer. there are 17 angles on a truck steer axle, 13 are measureable, 3 are adjustable.
@@keith6943 That's actually correct. However, the way the industry handles certain things is a bit messed up. In the video he was talking about adjusting caster, then stopped himself before he went on to camber. Your caster line runs through the 2 pivot points on your steering system. Upper and lower ball joints, lower ball joints and upper strut plate, etc... Caster line then gets referenced to true vertical, and any difference, positive or negative, is you caster angle. (Its always positive unless the vehicle has been in some type of accident, or problem. Most people don't realize that your caster line is used to make another angle called steering axis inclination angle (SAI). That's because you're working in 3 directions. In order to adjust caster, you need to move one, or both pivot points lengthwise with the vehicle. If you move a pivot point crosswise, you adjust SAI. Camber is a vertical line that runs through the centerline of the wheel itself, and gets referenced to true vertical. In order to adjust camber you need to adjust the tilt of the wheel itself.
Here's the problem, and what I believe he was referring to in the video. Many vehicles have you adjust camber by moving something that alters the crosswise position of one, or both of the steering's pivot points. Cam bolts on a lower control arm. Shims on an upper control arm. Slots on the top of the strut plate, etc... And its true. All of those adjustments will effect camber. But its not a direct camber adjustment. Its indirect. Its really an SAI adjustment, and camber changes because the wheel bolts to the spindle, and the spindle connects to the 2 pivot points. Its not necessary to move pivot points to adjust camber. A more direct adjustment is something like slotted bolt holes where the spindle bolts to the bottom of a strut. That will change camber without altering your pivot points.
What's kind of unbelievable is the industry ignores this for some reason. They all say SAI is not adjustable, yet they have you directly alter it to adjust camber. If you have taken your ASE's, they word it by saying, SAI is not "considered" to be adjustable. SAI is extremely important for how a vehicle handles.
Anyway, it was a good call on your part because most people wouldn't have thought it through, and you did.
👍
You the man
More videos plz!!
HEY HOW DARE YOU!!!!! I have a Matco 3/4 impact ….. I love it 😂😂😂😂😂
I run no regulator on compressor too . . paying to pump that air , get your full share
Nice!
Front end should have had a decent drift to the right, correct? Gotta love the hi-output milwaukee! How did the rear axles measure?
The owner of my company always argues with me about replacing the U bolts.
very smart, listen people!!!!!!
I know that voice it’s captain from Cool hand Luke . “What we got here is failure to communicate “
Id like to see you do 30 min indepth content
U bolts are simple to replace and bend up yourself. If you've got the tools that is. Different rod sizes and lengths. That truck prob has 3/4 20in rods
It is a Volvo, 20mm rods, 30mm nuts
@sinisatrlin840 I forgot it's a Volvo , I was half sleep and prob should of just went to bed. My bad. I was dam close though because if they needed that truck on road and there wasn't any 20 mm rods handy, guess what size I'm trying first, and if I don't like it then we go to 13/16 buy I'm pretty sure the 3/4 gonna handle that. Long as I was bending U bolts Noone ever asked me for a metric rod, seriously. I'm not saying that to be a dik bro, Noone ever asked for metric, never even thought of that till you made comment.
If there already a shim in there do you just add another or remove it and add what's needed or do another reading and install one proper thickness shim to solve issue?
QUESTION do You work with MD Alingement Mike Beckit..
nice
split toe screen?
This is fun
Why do you not reuse unbolts? Stretch?
Achieving better videos.
Bro i really like the hot camera the over exposure looks neat in the shop 👍
You almost make this shit hopeful, thanks.You make a good teacher.
Does anybody know the name of his shop?
Guess? I don’t think so!
Experience makes the master!
How long you been doing this? 20 yrs?
Top 5 things you most know, before you know, what you don't know before you start. 😅
Period
I'm so twisted i can't find the beginning or the end .
👍👊😎
Where are you located? Need some work done.
I'll join your channel cause you seem cool if you need help let me know I'm local to you
Anyone know where his shop is located?
Sum We're in Téxás ¿¿¿¿
😅 Know what I mean. Check your parts 😊