You ever considered getting one of those cheap pump up yard Chem sprayers work wonders for dealing with small fires I keep one in tractor along with fire extinguisher when cutting and baling hay I've put out a few hot bearing fires with the 2 gallon sprayer it's now my go to whenever I'm haying or cutting grinding and welding if your paying attention a little water goes a long way kind of surprising how big of fire you can put out with just 2 gallons of water. Great videos keep up the good work. 👍👍👍
Ethan need to look into getting a Doyle 12 in speed square they have a bigger flange to fit over bigger radius tubing they are badass help make things slot easier and faster! From ur friend John foster
Nice workmanship very old school over here in the UK we would probably have used a plasma cutter or a disc cutter over gas and a MIG welder not Stick but all credit to you and your skill
Hello sir, I very seldom comment, but I really enjoy your channel. I have watched several of your videos and also find it awesome you play my favorite music instrument. Great craftsman for sure. Thank you for sharing.
You Need to use a straight edge guide for your torch cuts a piece of angle Iron works Great.Makes it accurate and the whole job easier and Neater with a much better Fit up!!
Always nice to watch you weld & cut, w/all the information & strategy, in your craft. Hope to see you get your dozer runnin. I have a D4-7U Cat dozer. that I dont use much. What are your plans for your truck in the barn.
Hi Ethan. For cutting the square tube, what could be the difference in working time from "as is" to "cut, prep and ready to weld" between using the torch versus the cutting disk on the grinder? Thanks for your great videos. Already waiting for the next one. Sart0
Sorry taking so long to respond. That’s been an age-old debate torch versus cutting disc or plasma cutter. I would say it it all has to do with what you’re fooling with. I would say quarter inch material tube pipe plate it doesn’t matter grinder is going to win unless it’s in a place you can’t get to plasma does better on long stretches, and hard to reach places. And if the thickness is greater than 3/8 of an inch torch wins every time. Torch is cheaper to run than plasma or grinder. It’ll cut unlimited thickness given the right tip and pressures. Torch has the highest learning curve it takes years kind of like stick welding.
We all have Bullshit days last week I spent an hour grinding out a cover. It was Bullshit and always in a shitty position. Sorry for the curse words but it was a bad day.
Hope everyone enjoys the video and as always take care and God bless.
I always come runnin' when Ethan's Classic Work bell rings here on y.t.! Thanks for posting a new video. All God's Blessings...
It’s a pleasure to watch an artist do his thing. Great videos Ethan.
You are a really nice guy. I wish i had your disposition. "Thats a little annoying..." thats not a little annoying that SUCKS lol great work
You ever considered getting one of those cheap pump up yard Chem sprayers work wonders for dealing with small fires I keep one in tractor along with fire extinguisher when cutting and baling hay I've put out a few hot bearing fires with the 2 gallon sprayer it's now my go to whenever I'm haying or cutting grinding and welding if your paying attention a little water goes a long way kind of surprising how big of fire you can put out with just 2 gallons of water. Great videos keep up the good work. 👍👍👍
You are one of my favorite uploader on youtube. Great video as always!
Greetings from Sweden
Bless Ethan, glad to see you back for another GREAT 👍 video. Keep’em coming. Thanks 🙏
I remember back in the 80s we had the old 8 row fold up type
Ethan, outstanding work sir. Thank you for posting
Ethan need to look into getting a Doyle 12 in speed square they have a bigger flange to fit over bigger radius tubing they are badass help make things slot easier and faster! From ur friend John foster
Great to see you posting again! Nice torch/welding job.
YES!!!! CLASSIC WORK !!! YOU ARE SUPER RAD DUDE!!!!!!!!! YES! I am so pumped for this video.
Nice workmanship very old school over here in the UK we would probably have used a plasma cutter or a disc cutter over gas and a MIG welder not Stick but all credit to you and your skill
Good tips! Nice teaser on the cabover. Roundabout is a jammin' tune.
Another fine job Ethan good to see you posted another great video buddy. Keep turnin and burnin
Hello sir, I very seldom comment, but I really enjoy your channel. I have watched several of your videos and also find it awesome you play my favorite music instrument. Great craftsman for sure. Thank you for sharing.
MM77 Approved 👍🏼👍🏼
great to see you back in action,,,,best wishes from Orlando, FL, Paul
great video awesome work
I'm loving the Binders you have. And you have a great skillset and work ethic.
good cut on tubing keep up the good work
Excellent!👍🏻
Good torch work.
Always look forward to your videos
I just noticed you and I have the same herringbone Comeaux welding cap......Far Out Man.....PB
Good job keep up
Glad to see another video. Keep up the great work :)
I enjoyed watching show your talent. Myself I would have screwed that cutting like a banshee. Great job
Great work young man!
Great video man and it will be quite interesting to see what you do with that ol cabover.
You Need to use a straight edge guide for your torch cuts a piece of angle Iron works Great.Makes it accurate and the whole job easier and Neater with a much better Fit up!!
Great video need to make more of them when you get a chance
Great video man. You should do a full walk through of ketchup love to see it
Nice work man!
What I do is make a 2mm cut with the 9" grinder slitting disc that way the metal is clean also you can follow if the chalk line gets wet!!
Always nice to watch you weld & cut, w/all the information & strategy, in your craft. Hope to see you get your dozer runnin. I have a D4-7U Cat dozer. that I dont use much. What are your plans for your truck in the barn.
👍🏻🍻
Get you a fire proof blanket for summer jobs
That’s a great find 🦘👍
The outro 😂
Hi Ethan.
For cutting the square tube, what could be the difference in working time from "as is" to "cut, prep and ready to weld" between using the torch versus the cutting disk on the grinder?
Thanks for your great videos.
Already waiting for the next one.
Sart0
Sorry taking so long to respond. That’s been an age-old debate torch versus cutting disc or plasma cutter. I would say it it all has to do with what you’re fooling with. I would say quarter inch material tube pipe plate it doesn’t matter grinder is going to win unless it’s in a place you can’t get to plasma does better on long stretches, and hard to reach places. And if the thickness is greater than 3/8 of an inch torch wins every time. Torch is cheaper to run than plasma or grinder. It’ll cut unlimited thickness given the right tip and pressures. Torch has the highest learning curve it takes years kind of like stick welding.
🎻What is your thought on the Dr Blake Mystery theme music By Dale Cornelius? 👍🏴
I’ve never played it but it is a neat sounding tune. May have to look into that one.
That's a cool cutting guide howd you come by it
Flame tech ez cut
We all have Bullshit days last week I spent an hour grinding out a cover. It was Bullshit and always in a shitty position. Sorry for the curse words but it was a bad day.
U just don't see many old school hipper bedder