Tidy brickwork but can't understand why people still use plastic trays UPvc trays with Lead flashings attached are so much better, especially the brick ones even for blockwork as look neater No need for cutting in after or hassle just pull up and flash underneath Good luck with your channel Jagclamps are also a joy to use for line clamps
Cracking job mate, just for your info new regs we have you work to with your damp trays, we have to bed them and poke the damp out around 10mm, then scrape the joint out so the roofer can then poke his dressing under
Wherever possible build the flashing in, if that's not possible as Michael said bed the tray on a nice bed leave the tray poking out. Rake out enough for the roofer to get his lead in, otherwise he uses a grinder an rips the tray to bits. Also another thing to look out for is the lead wedges they hammer in sometimes to secure the lead, they push the tray back so the tray and lead don't overlap. If that elevation happens to be one that gets hammered by rain it can leak in.
It was always like that then for some reason it whent out of fashion and roofers had to grind out new work for there lead, most jobs done like that the tray is in the wrong place.
People may piss you off with their negative comments BUT can they do what you do NO. You can do an extension from start to finish including woodwork, steels roofing but the majority of brickies just lay blocks and bricks. Keep the vids coming Izzy
Cheers fella, do appreciate it🤜🤛 Water off a ducks back😂. However, I do appreciate constructive criticism, as I would be ignorant to not take that on board 👌 cheers for watching mate! Have a great week
@@IzzytheBricky One thing, you bridged cavity to form new build line, you shouldn't do that until you reach the lead line. at least install a VDPC against outer wall.👍
Mate you get better every day. And shows what us real brickies have deal with. Ie Renovatiom with existing. Top guys u both.. Was that a Rose trowel when on window mate? Take care
Thanks so much mate, appreciate it! Just finished editing the 2nd part of this video where the wallplate goes on🎉 keen eye, but no it's a 13" narrow London Marshalltown plastic handle bud! Hope you and the family are doing fantastic 💪 look after yourself mate☺️
Hi mate, I did put insulation in the cavity, just not much was shown, as I was quite focused on getting home before 7pm 😂😂 so decided not to film everything 😂
stepped dpc should follow the lead, so back of tray (the upstand) is in line with the lead usually about 75mm above finished roof line. Check out NHBC standards online, its free
just been watching your video and I can't believe you haven't continued the cavity where the new extension connects to the existing building this is really bad not only will this cause damp issues but also a cold spot, to tooth in is correct but not to create the minimum 50mm cavity is shocking the toothing will just hide the poor workmanship of not continuing the cavity, this is typical of a lazy builder who can't be arsed to do the job properly shame on you, if your going to post videos of work don't include school boy errors like this.
Just got home off a 13 hour shift tarmaccing.. now to sit back relax and watch someone else do some work😂 going to be a cracking video as always👍🏼
😂😂😂 ey mate, I'm exactly the same😂🤦 appreciate the support buddy!
Great job, therapeutic…greetings from Hong Kong!
Thank you so much my friend! Thanks for watching ☺️☺️
Drew putting them down man big respect.
Am going to make you 2 more stands for next week
Sic note coming in strong 🤜🤛💪💪💪 yes brother 🙏
Big thanks for the support Izzy 🙏
Tidy brickwork but can't understand why people still use plastic trays
UPvc trays with Lead flashings attached are so much better, especially the brick ones even for blockwork as look neater
No need for cutting in after or hassle just pull up and flash underneath
Good luck with your channel
Jagclamps are also a joy to use for line clamps
Brilliant work buddy! Hope you had a great holiday! Looking forward to the next one as always! 👍😁👌👷♂️🧱
Cheers my guy, ey Barcelona was amazing mate🍻🍻🍻☺️ hope your well! Hows college and everything!
Great effort Izzy boy your looking well mate nice sunshine
Thanks Milne! Hope your doing well and smashing it buddy
Cracking job mate, just for your info new regs we have you work to with your damp trays, we have to bed them and poke the damp out around 10mm, then scrape the joint out so the roofer can then poke his dressing under
Wherever possible build the flashing in, if that's not possible as Michael said bed the tray on a nice bed leave the tray poking out. Rake out enough for the roofer to get his lead in, otherwise he uses a grinder an rips the tray to bits. Also another thing to look out for is the lead wedges they hammer in sometimes to secure the lead, they push the tray back so the tray and lead don't overlap. If that elevation happens to be one that gets hammered by rain it can leak in.
I like how your boss leaves you to get on with it,normally apprentices aren’t trusted to be by themselves,keep learning 👍
It was always like that then for some reason it whent out of fashion and roofers had to grind out new work for there lead, most jobs done like that the tray is in the wrong place.
@@bricklayersworldwithandy6277 I think the value of lead and it getting knicked was to blame.
Ooo okay fantastic, I wasn't aware of that! Good to know, not gonna lie, first time I've done step trays😂👌 thanks for the advice Michael 🤜🤛
Looking good mate. Bet that looks well smart when it done. 👍👍👍
Cheers Mark! Yea it's slowly getting there mate! Keep having days off 😂 don't think I've done a full week in the last month or so😂🤦
@@IzzytheBricky 😂😂lol. I feel the same with all these bank holidays 😂👍👍
Good that you wear a mask. Wet cutting is even better
Yes, I always try and wear the best possible mask when doing dusty work! ☺️ Have a good weekend!
@@IzzytheBricky thanks you too
People may piss you off with their negative comments BUT can they do what you do NO. You can do an extension from start to finish including woodwork, steels roofing but the majority of brickies just lay blocks and bricks. Keep the vids coming Izzy
Cheers fella, do appreciate it🤜🤛 Water off a ducks back😂. However, I do appreciate constructive criticism, as I would be ignorant to not take that on board 👌 cheers for watching mate! Have a great week
@@IzzytheBricky One thing, you bridged cavity to form new build line, you shouldn't do that until you reach the lead line. at least install a VDPC against outer wall.👍
Nice job bud what’s the birds bangers like
How dyu become a bricklayer?
Tidy work. 👍
Mmm nice to see you filled your toothings up
Jobs looking good bro ;)
Cheers fella! Appreciate it mate
Mate you get better every day. And shows what us real brickies have deal with. Ie Renovatiom with existing. Top guys u both.. Was that a Rose trowel when on window mate? Take care
Thanks so much mate, appreciate it! Just finished editing the 2nd part of this video where the wallplate goes on🎉 keen eye, but no it's a 13" narrow London Marshalltown plastic handle bud!
Hope you and the family are doing fantastic 💪 look after yourself mate☺️
@@IzzytheBricky Yes I'm happy. Everton have stayed in the prem 😀😃😄👍💯
@@IzzytheBricky ok Buddy. Also look into the rigid plastic cavity tray system. For stepped work. U tube. ( for your increasing knowledge) 🤜👍
I thought a return for any corner had to be minimum of 450mm..? And did you put any insulation in the cavity.?…
It used to be 650mm but if the Engineer can provide calcs to prove otherwise it's ok.
@@bricklayersworldwithandy6277 ahhh yes 650mm god knows why I said 450mm..🤷🤷🤦🏻♂️
Hi mate, I did put insulation in the cavity, just not much was shown, as I was quite focused on getting home before 7pm 😂😂 so decided not to film everything 😂
Top job m8 ⚒
Cheers Scott, appreciate it buddy
Great job 😁👌👏👏❤️
Thanks Terry
Excelente trabajo 👏 👊 🧱🧱🧱👷👷👷
Hope you recharged on the hols pal looking good as ever not you the work 🤣🤣🤣🧱 good luck issac mate 👍 🤣🤣
Thanks mate! Its was a good holiday, but I feel I need a holiday to recover from it 😂 thanks so much Justin! Hope your well!
Always the same in it mate 🤣🤣🤣🧱 all good here over worked issac 🤣👍👍👍
Great job proud of you
Thanks Joe mate, appreciate it bud! Have a great week🤜🤛
What did you put in for insulation?
100 cavity wall insulation mate 💪
Arbo tech saw all day
1:20 - 1:43 absolute filth.
😂😂😂😂😂
Grasias por compartir este video soy de México pero trabajo en Chicago en masonry construction brick layer 🧱🧱🧱🔨🔨📐💪💪un saludo que buen trabajo
Thank you very much mate!
stepped dpc should follow the lead, so back of tray (the upstand) is in line with the lead usually about 75mm above finished roof line. Check out NHBC standards online, its free
150mm mate
@@kevinmyton122 no mate 150mm is upstand to front edge not the cut back
Minimum return on corner 450 he'll of a week spot especially with the weight of the corbell
Is there any particularly reason to use the concrete blocks on the outside skin above lintel or just to save laying two courses of brick?
The blocks will be hidden by the lean-to roof, just saved laying about 150 bricks, bit quicker and cost effective 😊👌
Dont do insta how else can I check out them stands and how much are they? Thanks
Hey m8 how can I help
@@sicknote26 enquiring about the stands price.
@Shinobi yeah but are they as strong as them ones 🤔
@@Oncewasdonka 100 unpainted 140 painted
@Shinobi not each for set of 2 stands not one
Grande IZZY
inside of that cavity is a bit much...
Where the window was taken down?
just been watching your video and I can't believe you haven't continued the cavity where the new extension connects to the existing building this is really bad not only will this cause damp issues but also a cold spot, to tooth in is correct but not to create the minimum 50mm cavity is shocking the toothing will just hide the poor workmanship of not continuing the cavity, this is typical of a lazy builder who can't be arsed to do the job properly shame on you, if your going to post videos of work don't include school boy errors like this.
Anthor good video and top work coming along nicely that job now 🧱👌
Thanks Daniel bud, hope you had a good weekend fella 🤜🤜
Nice one Izzy this need to patent that tray system mate 😆😆. I seen it working on Instagram today 👌🏼😉🧱👍🏽
Hahaha cheers Steve mate! 😉 I was so surprised 😂
@@IzzytheBricky . Bet all the haters got their eye wiped 😆😆🧱👍🏽🌊💧💦