Good job. Two suggestions: after you finish the windings, soak the bobbin with the coils in varnish and allow it to dry completely before you insert the lamination. Otherwise the coils can make some noise. second: The lamination stack should be pressed in a vice and bolted very tightly otherwise some magnetostriction hum will come.
if m not wrong, each tranformer is a step up 12v to 220v. Just connect 2 primary of them in series to make 24v and connect 2 secondary of them in parallel. No need to rewire
Nice work.!! But it gives 32-0-32 instead 32 0 35... why ?? Coz u added 38 (362+30) extra in primary but not in secondary... use extra round in secondary also.. in order to get 35 0 35 in working amp it should be 37 0 37 without load...
@@mujianto1420 aku masalah bikin trafo mulai ukuran kecil 1a - 15a aku bisa ngitung cara rumusnya. Klo ini aku belum pernah bikin trafo memakai gabungan kayak gitu mas broo. Nanti akan ku coba beli trafo dipasaran 5 biji mau aku gabungin juga jadi satu dirangkai ulang.
can i have a question? on how to identified the gauge/size of magnet wire that can used on winding the transformer? before i'll make this kind of project but i can't finish it due to the size of magnet wire's that i used is big instead of 50v-0-50v target on dc output the result 32v-0-32
It's just smaller high frequency transformer with feedback winding If you don't know you shouldn't be messing lol and there's loads of videos about it... FFS you lazy fucker
But according to design principle you have to avoid making stack height to width ratio > 2. I have found that the square core has the best fill factor and most efficiency. Though you could make upto 1.5 ratio to match the desired VA of transformer. These kinds of design makes low efficiency transformers with more iron losses. Better use bigger core to increase power handling capacity.
Además para tanta "potencia" uso alambre muy fino, y tenés como desventaja la reglutancia magnética (distancia que recorre el magnetismo) así que además de menos potencia menor rendimiento.. hubiera sido mejor usarlos con primarios en paralelo y hacer un arreglo serie en los secundarios.
Пропитка слоёв на таком каркасе обязательна. Потому что, очень быстро произойдёт пробой изоляции между витками. Кто разбирается в этом тот всё это знает. Удачи
Amigo, falo aqui de Fortaleza CE. acompanho seu canal e gostaria de tirar uma duvida. Preciso para meu projeto de amplificador um trafo com as seguintes características. Primário: 110/220V. Secundários: 35V 0 35V 5A e 15V 1A. Quais seriam os cálculos do trafo?
You should add insulation between layers, shortcircuit between layers is common problem in transformers even with good enamel on copper. Ofcourse this insulation gonna incerase Your transformer stray capacience but its worth to add it if frequency is low (when You made it by hand coz You have no option to vaccum impregnate it) Also Your insulation tape looks like masking tape... never use it to insulate windings.
Sir agar ham isi bobin ko 13 cm k bajye 15 cm karke 45 0 45 banye to kitne turn primary aur secondary turn dalna padega please reply jarur dijiga ham inzar me rhenge
А чего ж мотает проволоку в ручную? Сделал бы приспособу для перемотки катушек..... и внутрь катушки надо деревянный брусок влаживать, чтоб катушка не ужималась внутрь. Пару раз уже было - намотал проволоку, а железо вставить не могу, потому что катушка вогнулась.
hello mr i am an intern i am in ivory coast. I wanted to know how to determine the wire diameter of a primary and secondary inverter transformer. example case of a 1000w transformer
What about using the stator iron core of an electric motor? With that you get a toroidal iron core. All you would need is to cut off the edges of the innerside grooves where the coils are installed. That way you will have a ring core which you can use for a toroidal transformer which is known to be better than other transformers.
The laminations are facing the wrong direction and also the inner core of a induction motor is not suitable for a transformer because of the actual material used for it. Remember a transformer is not as simple as a lug of iron and copper wrapped around it
There's a formula for the number of turns and wire dia , for primary and secondary windings on a transformer. Not something you would really want to mess around with , unless you understand the basic principles of electricity.
Wrong calculations ! What is the watt's of it? He will gets 140 watts .some of the input energy is consumed by the device itself as it converts the energy into another form, typically heat, and that energy is lost.
A person who eats bread and transformers for breakfast hehehe. But shouldn't you also take into account the height of the winding? Use a plastic hammer, with the iron one you ruin the sheet metal You are wrong by 2 volts in the secondary because you have not taken into account the increase in size that the primary gives. Anyway Bravo
bro for frimer coils, 1mm wire in double or in parallel so that 2mm will be rolled together at the same time or not, then the N ends are joined with N and the L ends are joined with L or each end is joined thanks.
@@retsain ... dont think in amperes... try to focus on watts...so, the volt-ampère (VA) rating is directly proportional to the product of core area and the area occupied by the wires (copper areas)
Good job. Two suggestions: after you finish the windings, soak the bobbin with the coils in varnish and allow it to dry completely before you insert the lamination. Otherwise the coils can make some noise. second: The lamination stack should be pressed in a vice and bolted very tightly otherwise some magnetostriction hum will come.
Big respect sir. Tnx for your value knowledge
I learn many things about transformer making .this is one of the best channel I found from youtube about electronics .thanks for your videoes sir .
Hello Hello 😃😃😃😃
Yesa video hammer pure UA-cam channel par nahi dekha nice video
No one make this transformer in online but i have made one 😍 From this
🇧🇩 love from BANGLADESH
Very good! I have done this o lot of times 😁.
When the support of few transformers get burnt or destroyed, remain the E+ I parts...
Your work is out standing .
Very well done my brother.
I hope is it very havi .
You are creative, sir ... I watched this video until it's finished ...👍👍
Very informative I expect this type of evaluation by the way I can earn money.thank you , God bless you.
Mujhe technical video achi lagti hain main aisay kaam sekhna chahta hoon.apki video se buhat kuch sekhne ko milta hai.thank you.
I don't Know how, but you did a satisfating, intresting and useful video togheter
Wow, thanks
Please visit for diagram
electronicshelpcare.net/how-to-make-inverter/
Muchas gracias!!!el truco de poner cinta por cada pasada de alambre en los extemos de la formaleta me ayudo a que el bobinado me ocupe menos espacio
Your vdo is very nice thanks a lot sir for good job
O transformador ficou desproporcional! O comprimento não deve ultrapassar o dobro da largura do núcleo! Seria melhor fazer dois trafos! Abraço!
Great video.... I also following you..!!!
if m not wrong, each tranformer is a step up 12v to 220v. Just connect 2 primary of them in series to make 24v and connect 2 secondary of them in parallel. No need to rewire
Nice work.!! But it gives 32-0-32 instead 32 0 35... why ?? Coz u added 38 (362+30) extra in primary but not in secondary... use extra round in secondary also.. in order to get 35 0 35 in working amp it should be 37 0 37 without load...
Joss👍... hadir indonesia
Perlu di coba itu bang
@@mujianto1420 aku masalah bikin trafo mulai ukuran kecil 1a - 15a aku bisa ngitung cara rumusnya. Klo ini aku belum pernah bikin trafo memakai gabungan kayak gitu mas broo. Nanti akan ku coba beli trafo dipasaran 5 biji mau aku gabungin juga jadi satu dirangkai ulang.
Excelente ideia usar três núcleos fica melhor a distribuição do peso.
Pois ficou longo o transformador .
Fica também com pouca altura .
Muito bom 👍👍👍👍
Please visit for circuit diagram
www.pinterest.com/electrohelpcare/pins/
Seriously cool! I will try to make one. Your video inspired me :)
Mind blowing raw intelligence..
Good job! total VA ratings of the 2 transformers will be the VA rate of final product.
350w
Your art is wonderful
time wasting 😴 3 transformer parlel connect ..same power
Excellent work 👏
Muito bom.
Parabéns👏👏👏
Watching and sending support lheoda tech tv thanks for sharing
Good project and good work
can i have a question? on how to identified the gauge/size of magnet wire that can used on winding the transformer?
before i'll make this kind of project but i can't finish it due to the size of magnet wire's that i used is big instead of 50v-0-50v target on dc output the result 32v-0-32
He uses Winding Rule '42', A lot of guys use the rule similar to this one.
That mains power lead is the scariest thing I've ever seen 😢
Good job ❤️❤️ 🔌🔌🔌
What does this to increase your amperage?
Your video nice explains so first of all thanks and one more request pls explain switch mode transformer (SMPS).
It's just smaller high frequency transformer with feedback winding
If you don't know you shouldn't be messing lol and there's loads of videos about it... FFS you lazy fucker
But according to design principle you have to avoid making stack height to width ratio > 2. I have found that the square core has the best fill factor and most efficiency. Though you could make upto 1.5 ratio to match the desired VA of transformer. These kinds of design makes low efficiency transformers with more iron losses. Better use bigger core to increase power handling capacity.
Hats off to the hard work
I agree with you
Crative and good video, thanks for sharing
super bro good idea before iam also done same this for 45 0 45 v amplifier
I have a requirements for a transformer with output 110V with 2000W, can you please let me the quote for the same.
Dude this type of transformer you've made is less efficient than 3 transofrmers you've just used to make this one.
Además para tanta "potencia" uso alambre muy fino, y tenés como desventaja la reglutancia magnética (distancia que recorre el magnetismo) así que además de menos potencia menor rendimiento.. hubiera sido mejor usarlos con primarios en paralelo y hacer un arreglo serie en los secundarios.
Why ?
@@youssefdirani practically the fill factor is less in this stack height to width ratio. Best practice is to use square core if possible.
@@elrusosolda5386 sfggfgh gzfjj sgfghjj,hhfhjj ncf.
wtf is this language
Esso lo pensei yo tanbien, seria mejor@@elrusosolda5386
Пропитка слоёв на таком каркасе обязательна. Потому что, очень быстро произойдёт пробой изоляции между витками. Кто разбирается в этом тот всё это знает. Удачи
Amigo, falo aqui de Fortaleza CE. acompanho seu canal e gostaria de tirar uma duvida. Preciso para meu projeto de amplificador um trafo com as seguintes características. Primário: 110/220V. Secundários: 35V 0 35V 5A e 15V 1A. Quais seriam os cálculos do trafo?
You should add insulation between layers, shortcircuit between layers is common problem in transformers even with good enamel on copper. Ofcourse this insulation gonna incerase Your transformer stray capacience but its worth to add it if frequency is low (when You made it by hand coz You have no option to vaccum impregnate it) Also Your insulation tape looks like masking tape... never use it to insulate windings.
why not,please? what to use then?
Sir agar ham isi bobin ko 13 cm k bajye 15 cm karke 45 0 45 banye to kitne turn primary aur secondary turn dalna padega please reply jarur dijiga ham inzar me rhenge
Thanks very much I got very good idea
При такой длине провода надо пролачить на горячую, а вторую обмотку мотать сразу двумя проводами, чтобы сопротивление было одинаковым
Thats gangster that would make a sick 1 to 1 isolation core
U have not specified used wire was aluminum or copper?
А чего ж мотает проволоку в ручную? Сделал бы приспособу для перемотки катушек..... и внутрь катушки надо деревянный брусок влаживать, чтоб катушка не ужималась внутрь. Пару раз уже было - намотал проволоку, а железо вставить не могу, потому что катушка вогнулась.
Yeaaaa! What a great idea!!! Congratulations and thanks for sharing!!!
Is it for sell? I need one like that but primary 110vac.
Whatsapp me 008801980060190
Give me your number with country code please. I'm from The USA
hello mr i am an intern i am in ivory coast. I wanted to know how to determine the wire diameter of a primary and secondary inverter transformer. example case of a 1000w transformer
Kon sa tep lagaye ho bhai
Best information thankyou
wow brilliant work
Does 42 also applies for the Philippines?
What about using the stator iron core of an electric motor? With that you get a toroidal iron core. All you would need is to cut off the edges of the innerside grooves where the coils are installed. That way you will have a ring core which you can use for a toroidal transformer which is known to be better than other transformers.
The laminations are facing the wrong direction and also the inner core of a induction motor is not suitable for a transformer because of the actual material used for it. Remember a transformer is not as simple as a lug of iron and copper wrapped around it
I like it.I'll try
There's a formula for the number of turns and wire dia , for primary and secondary windings on a transformer.
Not something you would really want to mess around with , unless you understand the basic principles of electricity.
yes there's is formula for number of turns it's depends on you that how much power you need
Hola buen video, tengo una duda de que calibre son los alambres awg?
electronicshelpcare.com/wire-gauge-transformer/
Wrong calculations ! What is the watt's of it? He will gets 140 watts .some of the input energy is consumed by the device itself as it converts the energy into another form, typically heat, and that energy is lost.
Great idea you have! Thanks for share!
Sunil saini DJ ramen
U r using aluminum wire for both primary and secondary winding, that's it's easy to wind. Normally it's hard to wind 18gauge copper wire.
Bhut badiya idea h 👌👌👏👏
How many output Ampears give In This video Transformer .
Average 140 watt's !
wonderful transformer making for powerful amplifiers
I support you
no comments?? bet im the first one eh.. nice build btw.. just have one question is it more efficient over toroidal??
Ficou ótimo bom trabalho no trapo
He is the king
Why do you use 24 gauge wire here ?
Is there a rule for that ?
Pro total primary winding terns how much.
A person who eats bread and transformers for breakfast hehehe.
But shouldn't you also take into account the height of the winding?
Use a plastic hammer, with the iron one you ruin the sheet metal
You are wrong by 2 volts in the secondary because you have not taken into account the increase in size that the primary gives.
Anyway Bravo
Que bien se trabaja con material completamente nuevo...
Please visit for circuit diagram
www.pinterest.com/electrohelpcare/pins/
what is the size of the primary and secondary copper?
Hey you said in this video that Ac220v but actual ac220v is rms value so peak voltage around 300 so your winding should according this value 330v
Nice job!
What amp of this transformer..and how to calculate transformer amp..plz...
Please visit for circuit diagram
www.pinterest.com/electrohelpcare/pins/
bro for frimer coils, 1mm wire in double or in parallel so that 2mm will be rolled together at the same time or not, then the N ends are joined with N and the L ends are joined with L or each end is joined thanks.
This is what you do when you don’t have RadioShack in your village.
video bohat achi thi
nice sharing
Very nice idea...
How to choose the coil wire size for both primary & secondary?
electronicshelpcare.com/wire-gauge-transformer/
electronics help care
Thank you :-)
please help tutorial to make a transformer with primary 220v and secondary 230 v 0.300 ampere, 6.3 v 1 ampere and 9 v 1 ampere, thank you
Please visit for circuit diagram
www.pinterest.com/electrohelpcare/pins/
the iron core is too large The wire should be 2.2 mm if the wire (primary) 1.2 then the iron core is 18cmm2 (otherwise there is little space Üdvözlet!
Only one question: How many Amperes can supply this transformer?
electronicshelpcare.com/wire-gauge-transformer/
How to know the amperes of transformer using the given cross sectional area of transformer
@@retsain ... dont think in amperes... try to focus on watts...so, the volt-ampère (VA) rating is directly proportional to the product of core area and the area occupied by the wires (copper areas)
Sir kon se transform main kon SA taar use hoga
electronicshelpcare.net/?s=gauge
Wrapping the bobbin with masking tape is a poor choice - use Mylar tape, it’s designed for high temperature and high voltage.
Transformer eks ups, good👍
sir i need 24-0-24 v or 28-0-28 v. how many turns required. sir plz send answer.
I used to make these Transformers at a place called General Transformers out in Sache Texas
Please visit for circuit diagram
www.pinterest.com/electrohelpcare/pins/
300 winding :220V=1,36 winding 1V, ....35Vx1,36=47,6 (48 winding)
Wow bro brilliant
Best information thank you
Jum'at 5 Agustus 2022 21:56 WITA 👍
🔥🔥🔥
Sar jyada se jyada ham kitna lamba transfermer banaa sakte hain
mìn đã làm cách này để nâng công suất biến áp lên cách đây 12 năm rồi
How about using 2 transformer instead of 3? What is 42 stand for? Is it applicable to all transformer sizes?
Nice work. Total kithna ampiear, DC?
Nice video bro🖒
Apakah ini memakai kawat tembaga baru atau yg bekas
15-0-15 ,10ஆம்பியர் டிரான்ஸ்பார்மர் கிடைக்குமா?if soஎத்தன்ரூவா ஆகும்