It is looks good to make a bypass wire from ic-sn51dp, but the tapping in the swicth board is not shown in the video. Can you show it clearly sir? In another video?. Thanks very much.
Although it is not seen in the video, i try to understand and examine very will where he have going to tap the yellow wire. From the video itself he said that " the ic has no signal when you turning-on the manual switch ". The 3.1v is present on the signal leg of IC even turning-on the tv. Meaning the pulse 0 bit is not present. I conclude therefore, it needs 0 volt or 0 bit to activate voltage boost to " on " the LED back light. Therefore i connect the said yellow wire to the negative side of manual "power-on " switch. My work done. MORE THANKS
ভাই আমি অল্প কিছুদিন লেখা পড়া করেছি লিংক সমন্ধে বেশি একটা বুজিনা তাই আমার মোবাইল নাম্বার দিয়েছি 01918978092 কোন ভুল হলে ক্ষমার করবেন ভাই আমার হয়ত আমি ইংলিশ খুব একটা পারি না তবে আপনার ভিডিও দেখে আমি 3 টা led টিভির কাজ করতে পেরেছি ভাই 💖u my brother
Nice sir panel repair ke liye backlight table kaise banate hai aaj tak kisi ne video nahi banaya aap banaye
Good information vai Kemon acen apone ❤️ u
Awesome sir ji
Best of luck dear.....
Good job.
Yr's adds pls
Pura video plz achchi tarah se btaye
helpful
Glad you think so!
Stby. Par ek video banaiye isi bord par
🙏
welcome dear
What is the number of the backlight driver that you installed
What name in that small board?
Black light check Karne ke liye kintna DC voltage dena padega please reply
Hai sir backlight ic inverter card yellow wire ic 10 is solring or resistor solring configuration so please correct answer
Best
Excelente trabajo profe una consulta cómo se le puede quitar la raya blanca que sale
If there is a white stripe in the panel then it is a panel Problem.
@@ProHackHD ok muchas gracias
It is looks good to make a bypass wire from ic-sn51dp, but the tapping in the swicth board is not shown in the video. Can you show it clearly sir? In another video?. Thanks very much.
Although it is not seen in the video, i try to understand and examine very will where he have going to tap the yellow wire. From the video itself he said that " the ic has no signal when you turning-on the manual switch ". The 3.1v is present on the signal leg of IC even turning-on the tv. Meaning the pulse 0 bit is not present. I conclude therefore, it needs 0 volt or 0 bit to activate voltage boost to " on " the LED back light. Therefore i connect the said yellow wire to the negative side of manual "power-on " switch. My work done.
MORE THANKS
Welcome dear
Thanks sir
All the best
BG Music is like horror movie
Sabes como desbloquear el panel de teclas sin control remoto.
Very good video bhai kemon achen apne
আলহামদুলিল্লাহ,আপনি কেমন আছেন?
বর ভাই আমিও অনেক অনেক ভালো আছি /এবং আপনার ভিডিও অনেক সুন্দর লাগে
আপনার ফেইসবুক প্রোফাইল এর লিংক দিতে পারেন এখানে.....
ভাই আমি অল্প কিছুদিন লেখা পড়া করেছি লিংক সমন্ধে বেশি একটা বুজিনা
তাই আমার মোবাইল নাম্বার দিয়েছি 01918978092 কোন ভুল হলে ক্ষমার করবেন ভাই আমার হয়ত আমি ইংলিশ খুব একটা পারি না তবে আপনার ভিডিও দেখে আমি 3 টা led টিভির কাজ করতে পেরেছি ভাই 💖u my brother
Driver bord apke pass milenga ...sir
Please explain details.thank you sir
Keep watching
pls send me firmware of this mainboard 1600x900.
thanks in advance!
Tp. V56.pa671. Power Nahin a raha hai kya photo hoga
আমি কাজ শিখতে চাই কোনো ব্যাবস্তা আছে বস?
Como desbloqueo las teclas por favor
एल ई टीव्ही से धूवा निकला क्या हुआ होगा
i need this mother Board firmware
which resolution you want?
Give me your Gmail address.
7
sy
?
Hii
Mere ko kaneson fir se batado
Why r u playing so horrible back ground music?