It's gonna happen! Your garage door, gate, or window shutters will need fixing someday. Prepare now with my DIY video tips! Subscribe and join the community! Plus it motivates me to make more videos (it’s free) tinyurl.com/garagedoorsYT
the nice thing about the videos is I can listen and do the instructions at the same time the pacing is perfect an no unnecessary comedic side shows, you're legend man!! it took me a minute to sort a problem I have been battling for months!
For the last 6 months I thought my SD800 motherboard was faulty. The door would open just fine - every time, but sometimes it would take multiple (10-50) presses of the close button before it would it close normally. When the door didn't close, the unit would make a single 'click' noise and do nothing. The symptoms were not described in the manual or any where else on the internet before your video. I tried these exact steps and it fixed the issue instantly. I suspect the unit wasn't calibrated as well as it could when installed by the contractor during the build of our house (volume-builder) or after 4 years of use, the limits may have shifted enough to stop it closing effectively. The issue was progressively worse over 6 months and I was just about to buy another unit. Saved me hundreds of dollars getting someone out and/or straight up replacing the unit! Thank you!
Any ideas on an SD800 that suddenly isn't detecting any remote signals at all? I've re-done the open/close limits, wiped all remotes, but none of the remotes or the wall button are being detected when trying to add them.
Hey mate, I’m trying to reprogram one of my remote buttons to a different button. However I am unable to initiate the remote programming stage by pressing ‘P’ together with ‘+’ (Not getting that all sequence flash response) any advice if there is a different procedure? Thanks in advance Cheers
Unfortunately, there’s only one procedure. You could try and erase the memory first but I think that needs the same buttons pressed to initiate it as well. [66] Steel-Line SD800 how to erase your remotes and secure your garage ua-cam.com/video/-9qnCx0Z6Vw/v-deo.html Could be an issue with the circuit board, in that case the only fix could suggest is to install an external aftermarket receiver.
Sure can there’s some good wifi modules from Ali Express I use on my gate and door for under $50 or there’s lots of wifi door and gate openers you can Google which is a bit more expensive upto like $150-$200 which don’t do much more
It's gonna happen! Your garage door, gate, or window shutters will need fixing someday. Prepare now with my DIY video tips! Subscribe and join the community!
Plus it motivates me to make more videos (it’s free) tinyurl.com/garagedoorsYT
Not all hero’s wear capes and this is proof of that thanks you legend
Haha thanks man
the nice thing about the videos is I can listen and do the instructions at the same time the pacing is perfect an no unnecessary comedic side shows, you're legend man!! it took me a minute to sort a problem I have been battling for months!
Great to hear! Appreciate the feedback too, sometimes it’s tricky to get the perfect video. I also prefer to point instructionals 👍🏻
You're a legend. I had this issue and was going to book a garage door repairer and luckily I came across your video and managed to get it sorted.
Wicked that’s awesome 😎 thanks for sharing too !!!
For the last 6 months I thought my SD800 motherboard was faulty. The door would open just fine - every time, but sometimes it would take multiple (10-50) presses of the close button before it would it close normally. When the door didn't close, the unit would make a single 'click' noise and do nothing. The symptoms were not described in the manual or any where else on the internet before your video. I tried these exact steps and it fixed the issue instantly. I suspect the unit wasn't calibrated as well as it could when installed by the contractor during the build of our house (volume-builder) or after 4 years of use, the limits may have shifted enough to stop it closing effectively. The issue was progressively worse over 6 months and I was just about to buy another unit. Saved me hundreds of dollars getting someone out and/or straight up replacing the unit! Thank you!
Awesome thanks James hopefully it lasts quite a while longer now 🙌🏻
Thankyou for this video....allowed me to relax knowing that the door opener was pushing down. Great video, clear and easy fix.
You're welcome! Thanks for commenting too 🤗
You just helped me fix the garage door, your a legend, thanks mate!
Great to hear! Glad your fixed 💪🏻
Pure legendary stuff, thank you!
Thanks Mate, you just solve 1 big headache.
This video was an absolute life saver!! Thank you legend 👌
You’re a Legend for commenting 👍🏻
You're a life saver man!!! Thank you so much!
Awesome video u r an absolute legend
Thanks 😊
You are a living legend😊😊
😆👍🏻
Oh man u legend!!! Saved me some money! Thank you
You are my life saver. Thank you so much for the video
You are so welcome!
Thank you so much you are a life saver
Your welcome man
Great video you solved the problem very well
Thanks a lot 😊
You are welcome
Saved me....thank you so much!!!
You're welcome!
Any ideas on an SD800 that suddenly isn't detecting any remote signals at all? I've re-done the open/close limits, wiped all remotes, but none of the remotes or the wall button are being detected when trying to add them.
Probably faulty receiver
Cheers mate this sorted my issue out.
You’re welcome 👍🏻
I have this model, is there any way to increase the speed of the door?
Nearly all garage doors are Fixed speed I’m afraid
Awesome, saved me a call out $$ thankyou very much
Glad I could help
Thank You so much mate....
You're welcome!
Hey mate, I’m trying to reprogram one of my remote buttons to a different button. However I am unable to initiate the remote programming stage by pressing ‘P’ together with ‘+’
(Not getting that all sequence flash response) any advice if there is a different procedure?
Thanks in advance
Cheers
Unfortunately, there’s only one procedure. You could try and erase the memory first but I think that needs the same buttons pressed to initiate it as well. [66] Steel-Line SD800 how to erase your remotes and secure your garage
ua-cam.com/video/-9qnCx0Z6Vw/v-deo.html
Could be an issue with the circuit board, in that case the only fix could suggest is to install an external aftermarket receiver.
Legend. Ty helped heaps!
What about if the minus button does nothing when you press it, i am not sure if maybe my minus button is faulty?
Possibly. I think you can use the plus and minus buttons to open and close the door. Try open it with plus and close it with minus to test it.
can we add Smart Garage Door Opener to SD 800 to operate it remotely?
Sure can there’s some good wifi modules from Ali Express I use on my gate and door for under $50 or there’s lots of wifi door and gate openers you can Google which is a bit more expensive upto like $150-$200 which don’t do much more
Thank you so much! ❤
Glad it helped, 🤘🏻
amazing mate! appreciate
Thanks heaps! Have an awesome week
Could i get the speed to go faster or does it only go slow like that?
1 speed only
Thank you worked perfect
You’re welcome 👍🏻
Hey mate my garage door opens a few seconds after closing completely. Does this sound like a limit problem?
Definitely 💯
@@rollerdoors great thanks so much 🙌🏼
I've tried to do this but mine just does two click sounds 2 seconds apart, sounds like it's trying to operate but won't. Could the motor be stuffed?
If the limit setting doesn’t work and you still hear a click (this is the relay working) yes the motor most likely needs replacing I’m afraid
Thank you so much!
You're welcome!
Whats the black earth wire on the right of the unit?
That’s probably the antenna you’re looking at
My sd800 garage door lights are all blinking except for number 3? Can you please help me how to fix it please.
Not sure on that one perhaps look up any codes in the manual
legend
What to do if all lights blinking except 1 solid light 3. Our garage door not working with anything.
Haven’t seen that issue I’m afraid
Thanks so much ❤
You're welcome 😊
Thanks mate
🎉🎉thank you
You’re welcome 😊
I love you x
❤
Slow down mate
I would but the machine will time out and I would have to start over i'm afraid, they never give you enough time.