Hello, Did this immersion cooling work with Goldshell CK5 miner? In a coment you said that thermal paste need to be remove and replace by foil... On goldshell Miner (CK5, KD5...) They use only thermal paste (on heatsink...). I have order an enclosure and precise before my order it is for goldshell CK5 miner and your commercial service says that is ok, it is a plug and play system. I don't want to break my miner please, in many forum it say thermal paste is not working on immersion cooling, answer me back if it is OK for my CK5 miner. And nice video thank you. Hope to get more guide soon.
Thanks for the video. Did you do also a video for GPU immersion? On a comment you say that some parts (pads) have to be replaced, could you give more information of the reason, and which pad should be use instead? I have read that many parts of GPU will be destroyed on a long term immersion, in mineral oil... (plastic parts)
@@OfficialPadre You can use 99% vodka but it's expensive. Jordan_ Everyone uses IPA, he said it, and the container literally has IPA on it, how you did not notice that?
At the last step you always should use 99% IPA. Before, you can even wash it in the sink with tap water and dishsoap... You just never can leave it with water on it and let it dry, it will corode and/or some minerals from water might cause a short.
Dielectric fluid is not a cleaner that will dissolve residue, corrosion, dust, contamination. Ultra clean dielectric fluid - no point to waste it - alcohol IPA cleans well (we can use more expensive dielectric solvent but IPA is just fine), and can be filtered multiple time so we don't waste the fluid in the long run.
we will have them on stock this week. DCX universal fan emulator 4pin EMU001 Universal 4 pin fan emulator for ASIC and GPU miners. Equipped with 16Mhz high speed MCU controller in DIP package with inteligent fan speed emulation 2300-6400 rpm. Fits 99% of ASIC miners and GPU cards using 4pin fan connector. Just go to cryptocooling.eu and use any "get the quote" button
hi my control board lose the cpu and i change cpu with new one. but not working because cpu luck on firmware when update with latest firmware. i know about latest firmware but i need factory default firmware. when change the cpu , need to flash with factory default firmware , actually first release firmware that innosilicon company writhe on a9 zmaster miner. thank you
Just one question , I currently use fan blowers , to siphon heat away from the room, will this setup reduce the room heat ? Or do i need to spoof it away ?
95% of the heat will be distributed by the means of liquid transfer from the enclosure to the dry cooler. However, some of the heat will be radiated to the room. That depends on the room temperature. But of course, there will be a huge difference - significantly less heat than currently moved by air.
Don't have to use any fan spoofers. But fan spoofers are cheap, so I'm guessing everyone just uses fan spoofers, default firmware and overclock those to the limits lol.
Sometimes water is used alongside some soap to better get rid of the dust, but right after that you must use IPA to dissolve water remains into IPA, IPA then evaporates quickly, leaves no residue and doesn't cause any corrosion. Though most use IPA by itself.
Not really, you can down power the miners. But people buy it to overclock the miners by 50-80%, eliminate the noise (see another vid) remove the problems with corrosion, dust, overheat, corrosion, fire risk, continuous repairs. But to run the operation you may require AC unit which takes power, you need fans to remove hot air - so we eliminate that. System requires 180W per 40kW of heat transfer as only pump takes power. More - cryptocooling.eu
I can supply you miner from China, and it is no scam I import many things from China and so I do these too. Let me know if you are interested. I can provide you a Innosilicone A6+ LTC master and others let me know if you are interested.
I strongly recommend you do not buy any things from DCX immersion cooling system , this video is only show , I pay 4 months ago supposed to receive in 5 week I never received . They don’t have any system at all.
Fantastic video Flip. Thanks for the link.
Can u help me plz? How long time until the oil need to be replaced? Can we use mineral oil?
Excellent, thank you for sharing this!
Welches Öl verwendet ihr als Dielektrikum und Kühlmittel?
Thank you for the great information
Hello,
Did this immersion cooling work with Goldshell CK5 miner?
In a coment you said that thermal paste need to be remove and replace by foil... On goldshell Miner (CK5, KD5...) They use only thermal paste (on heatsink...).
I have order an enclosure and precise before my order it is for goldshell CK5 miner and your commercial service says that is ok, it is a plug and play system.
I don't want to break my miner please, in many forum it say thermal paste is not working on immersion cooling, answer me back if it is OK for my CK5 miner.
And nice video thank you. Hope to get more guide soon.
Muy bueno el video. Gracias
Where its possible buy a immersion oil system ? In low quantity thanks
Thanks for the video. Did you do also a video for GPU immersion?
On a comment you say that some parts (pads) have to be replaced, could you give more information of the reason, and which pad should be use instead?
I have read that many parts of GPU will be destroyed on a long term immersion, in mineral oil... (plastic parts)
Is there special type of alcohol you need to use? Looking forward to trying this.
vodka not good B)
@@OfficialPadre You can use 99% vodka but it's expensive.
Jordan_ Everyone uses IPA, he said it, and the container literally has IPA on it, how you did not notice that?
@@Arek_R. 99% of vodka out there is no good :)
So cool!
Did you tried it with a Goldshell KD5 ??
i have one question.. we must remove thermal past ?
Swap it if it's not mineral oil compatible. You still need the heat sinks.
What will be the machine life if you use the cooling liquid. Will it prolong its useful life period of the ASIC miner??
Keeping your hardware at lower temperatures always will prolong its life.
where can i buy these chips that simulate a fan ?
Do you use 99% IPA? I saw another video where uses demineralized water and IPA 1/3 solution, is this ok?
At the last step you always should use 99% IPA.
Before, you can even wash it in the sink with tap water and dishsoap...
You just never can leave it with water on it and let it dry, it will corode and/or some minerals from water might cause a short.
can i use it for aisen a1 24th which psu in it it cant be out of the oil
Hello, this system with overclocking firmware on a10 pro 720mh. What hashrate we can got?
Hi how much per litre ?
Is 75% Isopropyl Alcohol usable?
Can't you just wash it with the cooling liquid, then use another fresh batch of cooling liquid for the immersion?
Dielectric fluid is not a cleaner that will dissolve residue, corrosion, dust, contamination. Ultra clean dielectric fluid - no point to waste it - alcohol IPA cleans well (we can use more expensive dielectric solvent but IPA is just fine), and can be filtered multiple time so we don't waste the fluid in the long run.
@@DCXLiquidImmersionCooling IPA Alcohol filtered? How?
@@OfficialPadre dielectric filtered. Alcohol for pre cleaning
Thanks for sharing this, one question
Where can I buy the fan spoofer?
we will have them on stock this week. DCX universal fan emulator 4pin EMU001 Universal 4 pin fan emulator for ASIC and GPU miners. Equipped with 16Mhz high speed MCU controller in DIP package with inteligent fan speed emulation 2300-6400 rpm. Fits 99% of ASIC miners and GPU cards using 4pin fan connector.
Just go to cryptocooling.eu and use any "get the quote" button
@@DCXLiquidImmersionCooling how much it will be
fan spoofer?
@@ghostdark4515 depending on quantity, but 9 usd - just ask for quote on cryptocooling.eu
hi, could you make a simple video installing some ASICS inside the box it would be very helpful I saw use for new buyers THANKS!
@@kluiverthramirez5398 will do more videos in 2 weeks. Stay tuned.
hi
my control board lose the cpu and i change cpu with new one. but not working because cpu luck on firmware when update with latest firmware.
i know about latest firmware
but i need factory default firmware.
when change the cpu , need to flash with factory default firmware , actually first release firmware that innosilicon company writhe on a9 zmaster miner.
thank you
Just one question , I currently use fan blowers , to siphon heat away from the room, will this setup reduce the room heat ? Or do i need to spoof it away ?
95% of the heat will be distributed by the means of liquid transfer from the enclosure to the dry cooler. However, some of the heat will be radiated to the room. That depends on the room temperature. But of course, there will be a huge difference - significantly less heat than currently moved by air.
I am looking for s9 hash boards please someone help
I've never seen alcohol electronics cleaning before. What percentage alcohol is it? Laboratory grade, 100%?
No chemical is 100% pure.
They used something that is like 99%-99.99%.
Using IPA to clean electronics is very common.
I got 99 percent from ace hardware
What's the benefit of the manufacturer's immersion firmware if it doesn't allow overclocking?
nothing!
Don't have to use any fan spoofers.
But fan spoofers are cheap, so I'm guessing everyone just uses fan spoofers, default firmware and overclock those to the limits lol.
Hey boss can you use plain water 💦 to clean? Will the water cause damage?
water is not good for cleaining it
Sometimes water is used alongside some soap to better get rid of the dust, but right after that you must use IPA to dissolve water remains into IPA, IPA then evaporates quickly, leaves no residue and doesn't cause any corrosion.
Though most use IPA by itself.
Does it use less power this way
Not really, you can down power the miners. But people buy it to overclock the miners by 50-80%, eliminate the noise (see another vid) remove the problems with corrosion, dust, overheat, corrosion, fire risk, continuous repairs. But to run the operation you may require AC unit which takes power, you need fans to remove hot air - so we eliminate that. System requires 180W per 40kW of heat transfer as only pump takes power. More - cryptocooling.eu
Czy mogę zatopić antminer razem z zasilaczem?oczywiscie wyciagnalbym rowniez wiatraki z zasilacza
of course you can.
@@DCXLiquidImmersionCooling what kind of fluid you using or can You recomend any for me?
@@johndeerempolondynie6441 Thermasafe R, just go to cryptocooling.eu and use red "get the quote button"
Where I can find this jumper chip to put out Fan's?
Please go to cryptocooling.eu/ and use red button - get the quote. Thanks!
Please go to cryptocooling.eu/ and use red button - get the quote. Thanks!
Hey do you sell the asic miners?
If yes then can you supply it to india?
I can supply you miner from China, and it is no scam I import many things from China and so I do these too. Let me know if you are interested. I can provide you a Innosilicone A6+ LTC master and others let me know if you are interested.
blyat 3:28 I used all alcohol to calm my nerve while cleaning
Same job with gpu, please!
Will do. There are little differences. You need to replace thermal paste with foil and sometimes replace thermal pads, but it's not a big deal.
@@DCXLiquidImmersionCooling I'm working in this direction too, with your units. Excellent job all around, congrats
@@euronymous86x please reach me via the website through the contact form and I will send you more details about GPU retrofitting
Jesteś z polski ?
tak bazujemy w PL
Thanks you say errrrrr alot 😂
5$ bucks to whoever can tell me, how many times he says ," uhhhh "
I strongly recommend you do not buy any things from DCX immersion cooling system , this video is only show , I pay 4 months ago supposed to receive in 5 week I never received . They don’t have any system at all.
Hi what's the name you used that replaced fans ?
Fan spoofer