I know right! Even while driving, it's like, hey, wait, what, how, why...will it stop now? Will it move? What's happening???? But, with a manual, it's like, yup, I got this... I know what needs to be done!
I get your point, but the fact is that an automatic will always be more comfortable than a manual, simply by how it works. But you're absolutely right, manual can be smooth too! It just requires more skill
@@huiba1 that's assuming the car is shifting well. I can shift better than the car I currently own. Though I guess it's mainly just your personal preference.
@@scottwesner9362 I daily an automatic, but got my license in a manual. And I agree! Some automatics shift horribly but modern ones are generally very smooth.
The author should apply a link to the planetary transmission setup explanation video. Also heavy loads are using automatic transmissions since there is not much place for human error. Especially computer-controlled automatic ones. I mean relatively heavy like for example a tank transmission. Another example can be a system in the "semi-trailer" truck. It is true you can put more on smaller manual transmission but in this case, you have to rely more on the operator skills. Also, a heavy-duty manual transmission becomes rough to operate if the applied load is raised very high while the system weight, placement, and size limitations occur. It's more due to the simplified clutch than the transmission box itself. What's most important is the system's live-cycle overall cost. It's sometimes even more important than the physics ;)
@@cautarepvp2079 You put the car in first gear and crank it. You can also start the car by putting it in gear rolling the car and then "popping" the clutch
to make it easier to understand, u gotta start with bicycles.. if u see a mountain bike or racer (those with several gears) then that is the same concept... smallest sprocket on pedal+largest sprocket on rear wheel=1st gear... larger sprocket on pedal+smaller on rear wheel=higher gears.. u notice when bikers try to climb uphill they mostly use 1st gear, although it takes a lot of pedaling to move the rear wheel to one rotation, it is still bearable same concept with cars... 1st gear is the slowest just like uphill on bike with low gear BUT its got power..but when u go faster u should use higher gears because at that point, inertia is your friend, and u dont waste your engine power
I prefer a manual. Better control (engine braking for example), smoother shifting (provided you know how to drive a vehicle with a manual transmission), and better fuel economy. Also I've had automatics that at certain speeds and loads couldn't decide between 3rd and 4th gear and kept shifting between the two giving you whiplash.
İ can engine break with my automatic. For amount of time i can set the gear i want for short periods by shifters behind wheel. Or i can make it completely manual
I'd prefer manual if I wanted to drive for fun, and an automatic if I wanted to drive without thinking too much. I think in the long run cruise control w/ an automatic transmission has been shown to actually have the best fuel economy, at least if you are on a highway and don't have to brake frequently or speed up of course. I just can't imagine spending 8 hours on a roadtrip with a manual transmission, but I guess thats why SUVs don't really have manuals.
@@yesyes-om1po Road trips are probably the easiest drive in a manual though. Just throw it into your highest gear once you get to speed and just keep cruising. It's the commute that can be rough in a manual, especially if you live somewhere with heavy stop and go traffic.
you don't have to engage the clutch before breaking, that would lower the fuel efficiency. Press the clutch before the rpm get under the idle speed, that saves fuel and reduces the brake wear
@Dragneel dude, if you need to go from 100 to 0 in 5 secs, you should not press clutch man. Because you want to prevent an accident. Stalling your car is better than wrecking it
@@Agent-1220 yep both pedals decreases braking distance if the brakes get warm, you don't want to be having to stop the engine from spinning as well so disengage the clutch
@Marko Djurdjevic you don't understand. It isn't about skills. It is about technology. It is physically impossible to do not loss power while changing gear you can drive like God. You can use mechatronice to automate manual transmission to have perfect gear changing. But you will never get rid of it. You can only minimize feeling of it because car have big momentum. And no. In modern automatic transmission there is no gap between.
@Marko Djurdjevic you need to learn about engeenering and probably not about driving. Your knowledge of physics is not a related to how many kilometers you have traveled man.
As long I live in a region that gets snow, I will own a vehicle that has a manual transmission. There have been many times when I would have been hopelessly stuck if I had been driving an automatic. I was able to use the clutch and gas to "rock" the car out of a stuck spot. That probably shortens the life of the clutch, but it is better than being stuck in a snowstorm for hours or days.
Whether or not snow is a problem depends on the car itself and the tires. If that weren't the case sure some automatic shitbox would probably do a lot better in snow than an Iveco LMV
@@LucidDreamer54321 It also depends if you are a larper who has driven an automatic once 20 years ago such as yourself. Do you even know how traction works?
No no no no. You do NOT press the clutch before applying the brake. The sequence is ABC: foot off Accelerator, foot on Brake, when nearly stopped depress Clutch. This is keeps the clutch engaged until the last minute and the car is better controlled. Pressing the clutch first results in a surge forward - acceleration of the car. I am a UK driving instructor.
Engine braking is not only helpful for control, but for slowing the car! Never, EVER release the clutch unless you are downshifting to improve engine braking!
+TRLWNC1 The way I've always taught my pupils, is not to change gear at all when slowing down. Change gear when you have reached your target speed, or use the clutch just before the engine shows sign of being unhappy when stopping. Changing gear disengages the clutch and makes the car less stable during those moments.
The smoothness of the manual transmission is something that you learn with practice, so that can be a bit misleading information. In the other hand, it is recommended to have the engine engaged during breaking all the way before it starts to stall. By leaving the engine engaged you let your engine help you slow the vehicle down, saving a bit on breaks. I will also like to add that driving on downhills manual also helps to avoid the vehicle gaining too much speed, thus also not depending merely on break pads. Just saying…
The trade off then becomes how much wear you’re willing to put on your transmission. I prefer to just use my brakes since they’re easier to replace than a transmission. Definitely useful when going downhill though
Also I’ll add that you will use more gas using engine breaking and your engine will rev higher causing more wear and heat. I’ve decided that a brake pad job is easy enough than to stress my engine and clutch and trans. But for racing, engine brake is where it’s at.
@@BosisofSweden I believe Daniel's talking about 6:35. He says that you _must_ press the clutch pedal completely before braking, which is not really true. When you're slowing to a stop you leave the clutch engaged to take advantage of engine braking. Obviously you disengage the clutch when you get to a near stop, but you can absolutely use the brakes while taking advantage of engine braking to decelerate to a stop. If you're familiar with heel-toe technique for downshifting while braking, that's exactly what's happening to slow the car down.
@@danielplasencia7271 no, they don't. You gear down and motor brake if you have learned to do it the correct way. If you end up to have to stop you use no gear as you wait och the lowest gear with the clutch down if you are about to go
He mentioned, "Heavy Duty Equipment"... When you have a "Heavy Duty Equipment" going down on a long hill or mountain, you don't want your brakes to overheat, so you use the transmission as an engine braking system...
@@g0nzal0id the downshift is the immediate break , i m talking about engine break that u will feel if u release the race , the car will slow down , if u press the clutch u l see that the car slowing down isnt as quick as it would be without the clutch meaning the engine is stopping the car while in gear
The people that invented these things are geniuses. I'd love to see a similar video about electric car engines. Would the automatic gear system be the same?
An electric car dont need to shift gears as the 3 phase VFD controlled motor in modern electric cars operate between 0 to 7-8000 rpm with no problem while an internal combustion engine works best between 800 - 3000 rpm, hence the need for many gears to keep the engine in that speed range. Also the tourque is at max at a certain rpm for a combustion engine unlike the electric motor wich have 100 % torque from 0 rpm through its entire speed range.
Learn Engineering Fantastic! Cheers to everyone making these videos. I love how clean, detail, professional and informative they are. You guys are awesome. :D
Most hybrid and electric cars use a CVT (continuously variable transmission). Which basically means that you don't have SET gear ratios. What happens is that the gear ratio gradually changes as you go faster, so as you accelerate lightly, the RPMS will stay somewhat in one place. If you Floor the gas pedal, the transmission will hold onto a lower gear ratio for longer to get that better acceleration. The simplest explanation I can give you is this: Picture a large cone shaped object, then picture a belt riding on that cone and attached to the transmission output. The gear ratios change by sliding that belt back and forth on that cone. It's like a bicycle, the bigger gears on the crank will give you higher ratios, and when the chain gets put on a smaller gear, the gear ratio becomes lower. The only fundamental difference between that and a CVT is that the CONE shape allows the belt (or chain) to slide up and down gradually, changing the ratio. Hope that answers your question!
Shadow Heart the answer would be no, most electric cars have direct drive, wich means no gears, no shifting. this is because an electric motor is not limited to a specific range of rpm like gas engines. they are much simpler with far less moving parts. they can deliver power to the wheels over a much wider range of motor speeds.
honestly, as much as traffic makes me wish i had an automatic transmission (seriously, operating the clutch and constant swapping between the 1st and 2nd gear is a nightmare) i have to say, that in almost every other non-traffic situation, manual transmission is pure joy you basically feel every single move you make you can rev the engine if you want you feel the sudden surge of power when you change the gear and quickly release the clutch pedal while revving the engine i honestly recommend everyone to try the manual transmission at least a few times if it's possible
If you care about your transmission, you shouldn't release the clutch pedal too fast. As the video explained, the Synchronizer Ring is matching the speeds, but if you release too fast, it doesn't have the time to actually do its work and as such tear a lot more. And well, repairing a transmission is pretty costly.
@@kuhluhOG i agree, and by "quickly" i didnt really mean "instantly" the sole feeling of sudden sharp shaking is probably enough to make most people understand that also if you rev the engine enough before releasing, it will fit in just perfectly
I would reccomend people trying automatic at least once.. manual is manual and you feel the car and really handy on ice starting from second gear or in adding torque in corners playing with right leg.. it is the way to drive a car for millions of reasons. Automatic won't make a proper driver out of someone. Name me one car racer that drives automatic?
@@BushcraftEurope well, Formula 1 cars have a sequential half-automatic transmission meaning: 7 forward gears (+ neutral + 1 backwards), they can only switch to gears next to the current one and not too fast, they don't have a traction interruption and they only choose which gear the car should be in (the rest is done by the software)
@@Henk14789 when my dad was teaching me to drive he told me about engine breaking and how good it is. He also added: clutches are more expensive than brake pads. 😂 Use your brakes to brake people, don't engine brake.
@@groundloss Engine braking is good for when you have a long enough distance to go, or if you need to slow down faster than just letting go of the gas. Traffic behind you should have enough time to see you slowing down even without the brake lights--assuming they're not distracted by playing on their phones... And your engine can handle shifting back into a lower gear just fine, assuming you don't skip gears. Your brake pads will wear down a lot faster if you exclusively use brakes.
At 3:28 “A manual gear drive is never a smooth experience.” WRONG! It depends on the driver and how long that person has been driving a specific vehicle. The trip can potentially be as smooth as with an automatic transmission. In my case for example, I have been complimented by passengers who say they often can’t tell when I am shifting except for the fact that they see my hand move.
I just watched a 1936 video about differentials... I understood it. It was 6 minutes, I know how differentials work now. No idea how transmissions work. Maybe the 1930’s have another video.
There is a 1930s video on transmissions. I think it was called levers or something. I think this video expects you to have basic knowledge on mechanisms (such as planetary gears) whereas older videos go over more, albeit to less depth.
Dear patrons Sorry, I couldn't publish your name/photo toward the end of this video. The climax scene of this video was filled with so much information that there was no space left to display your name. Sorry for that. I will show your name/photo from the next video onward. Thank you for your continued support.
Learn Engineering mate that's why we love manual that "variation of speeds" helps a lot in mountain road or in a drift course so in other words auto is good for inexperienced drivers to go from point a to b (sub humans) and manual is for much more experienced people (car guys/petroheads) who love the turns on a mountain or a racetrack 😉
HH E I hope, you are taking about AMT. They are just computer controlled manual transmissions. They have all the drawbacks of the manual transmissions.
6:39 "Before you press the brake pedal, you have to press the clutch pedal" So wrong.. You should brake with the engine engaged until you almost reach idle rpm's, then press the clutch and brake further. That way you both save the brakes as well as the car's computer knows you're braking on the engine so it won't inject fuel = better milage and lower emissions.
When you drive manual you quickly get used to disengaging the clutch at the right time for the current gear. Also, this is not directed at these two comments, but the video also said that a manual is never smooth. Which is also wrong, you can achieve a smooth shift. EDIT - It can be smoother than any auto I've driven so far.
Johann Kuhn Yes, but quite frankly it's very difficult to ALWAYS shift smoothly in a manual. There will almost always be some jerking at one point or another, especially if the engine's cold.
Something not mentioned - automatic has a noticable and significant lag in it. In a manual, when you step on the throttle, since you are mechanically connected to the transmission, power delivery is instant. In an auto, it takes a small bit of time for the torque converter to begin pushing the transmission forward. Then, if there is any shifting occuring, there is a significant lag before full acceleration. Manuals, assuming you know how to properly drive one, acceleration is again, nearly instantaneous.
Yes. And there are chipsets that can speed up this process. I have one installed on my Chevrolet S-10 2018 and the difference is noticeable when you need power to overtake someone in the road or for going from a stationary position to instantly high acceleration. I would say is a must have for safety purposes since your car becomes much more responsive when needed.
Two ways to resolve this (I've tried both, they work): 1) use so-called SPORT mode, it forces AT to shift down when you slam that pedal and has a significantly less reaction time compared to regular AT mode; 2) modern AT have a kick-down, which activates when you push the accelerator down to the floor and then some (you'll feel the bump when you press it enough), that'll force AT to give maximum power at the current gear, but be careful not to overrev the engine. There's also a third way, which is manual shifting, but I haven't tried this on the road yet, so can't recommend.
very clear it helped me understand how gear selection works, cause i really had trouble understanding how it didn't just go at one speed at all times but the visual helped so much thanks
@crummyy no they don't. The motor is directly coupled to the wheels tharough a single gair pair and deferential. The motor doesn't stall at low speeds like an IC engine would so you don't need to disconnect it from the wheels
"Let me introduce another planetary set that you still don't understand to explain how this is achieved. The output of the second planetary set is attached to the input of the first. It's simple!" ....
Pretty much always with the videos this channel uploads. They pop up in my feed as some kind of intellectual exercise where you have to google things elsewhere to understand them. These videos merely introduce the concept for me.
@@Inferamusic Each stage of the planetary is sort of like a separate gearbox. So, each stage gets multiplied by the other. If 3:1 and the next stage is at 2:1 the output will be 6:1, or, if you have 1000 rpm coming in you'll have 6000 rpm going out.
@@AzzaYaDog i think artur is mentioning about how some new drivers may make the body of the car make a tugging feeling because they dont switch gears smoothly or dont rev match to make a smooth transition, where as experienced manual drivers make it seem like there is no tugging by doing rev matches and smooth clutch engagements, hes not talking bout power not going to wheels
the point is even if it toke you .25 of a second, you still lose power from the engine in Manual gear, while the automatic gear never lose power from engine.
@@khaled00962 still you can just turn the engine high enough and then switch into the next gear very smooth so you won´t jerk at all (sry i speak german xD)
6:36 That's one of the biggest mistakes. You never disconnect the engine, by doing so on a downhill slope momentum can really take your car. Engine braking is used combined with braking. Never disengage the clutch unless you're ready to stop completely. When you want to go slower, just go to a lower gear. Also on downhills, it's better to be in gear and using the brake to have almost no fuel consumption.
I thought I was the only one who noticed it. The use of clutch while breaking is to prevent the engine coming to a halt while in gear, or in a complete stop, only.
They demonstrated it very poorly unfortunately. Engine braking is a well known and well used practice in cars with manual transmissions and fuel injection systems.
@@theedgarthefish4267 Yes an the second one with the woshhh would be an exhaust brake (on certain engines and vehicles it makes a hissing noise) and yeah I think they're technically still forms of engine braking, just diesels don't brake well on their own without mechanisms
Cameron, let it slide.. video most probably made by a 'murican who never drove stick. You've seen the graph? What moron can't drive stick smooth as babyoil? Then I remember, manual transmission is the best anti theft system in the US
@@3goats1coat haha i mean you lose power when you change gears ether way . there is a reason why automatics shift faster and better. but manual is so much more enjoyable exactly that "loss in power" is so much fun when you press gass a bit then change gear and you feel car tug forward damn that is exiting.
@@luk4s56 well, you lose traction for less than a second and more than a ton of steel being in freeroll.. you get what I mean, there's literally no way for a passenger with closed eyes to feel when you shift (except if you want to). Also, there's a reason why drift and rally both use manual. You're losing a lot of control over your car for that bit of comfort. Also safety, I'd say (considering tight overtakes).. the knockdown needs an eternity to activate, with manual you can be at 4k RPM with a howling turbo in a split second.
@@3goats1coat true i agree. its just that auto is more convenient. thats all there is but also i think its good that auto is popular. inexperienced drivers with manual are terifying to meet on a road
+Flix You are really lucky. where i live its traffic jams, frequent lights and constant up and down slopes. It is a nightmare. CVT is the best choice where i live.
Misha Sleptsov... ah, driving stick for experienced drivers becomes so 2nd nature that it doesn't matter in a traffic jam, you don't think about it one bit...
Whats enjoyable about having to cancer around with the gears? Yeah you have better control, but for what? Most people can't even deal with that and switch gears too late and just waste fuel.
Learn Engineering Dear Learn Engineering, Will these principles covered in the video be taught generally in automotive engineering courses in university?
Learn Engineering This video was very interesting. I am studying mechanical engineering in university and i am hoping to get into the automotive field. Thank You Learn Engineering for the depth explanation :)
Actually you don’t have to engage the clutch in order to brake. It just makes the transition of shifting down smoother. The clutch only has to be engaged when you’re stopped
@@tomzu8848 You don't have to do it, bur rev matching when downshifting reduces strain and wear and tear on the clutch assembly and transmission. Downshifting without revmatching forces the transmission into a braking type action which is not what it was designed for
@@theedgarthefish4267 strain and wear without rev matching on normal driving is so minimal it doesn't eat transmissions lifespan lot. Unless it's some glassbox that has been poorly manufactored/designed.
This video is too oversimplified. EIDT: I do not want to say that I dislike the video. But this topic is actually way more complicated. This video gives a nice and well animated introduction and those who want to learn more can do so. I encourage anyone to do it.
8 років тому
Which video would you suggest that does not oversimplify? Also: can you point out at least a few points where it oversimplifies. I am not doubting you, on the contrary. I am learning, so I am really curious to understand that.
Cláudio Sampaio I recommend starting with Wiki: en.wikipedia.org/wiki/Manual_transmission and en.wikipedia.org/wiki/Automatic_transmission The fluid coupling, also used in this video, is a part of many automatic transmission systems. Contrary to a clutch, it will always exhibit some level of slip and cannot completely "disconnect" the transmission from the engine either. Buses usually have a torque converter, which needs even more power to run but offers smoothness over efficiency, making diesel run busses accelerate equally like electric trolley buses. There are other transmission designs like the two clutch DSG automatic transmission which does not have a fluid coupling or torque converter, but even this type has its flaws (like when you decide to change from acceleration to braking or from motor braking to acceleration at the time of the transmission changing gears. Even this description is oversimplified.
Cláudio Sampaio one big problem is that this video shows the automatic as a superior transmission the thing is that, if you are good at it, you can shift quicker with a normal (manual) than with an automatic. also the atomatic is way heavier than a manual good thing about the auto is that you dont need 2 hand and 2 feet to drive it
Its not confusing now they have been awhile you ass hat. All he said was the people to originally come up with this are smart. Now stfu and get off your high horse.
Years and years of projecting the and re-projecting it, results in a more complex mechanism, if you're new to this engineering stuff I'm not surprised that you'll not understand it from the beginning.
brake not break. apart from that, i agree, press if braking in order to stop not to slow down. otherwise you loose inertial engine brake and you will end overheating the brakes. but on today cars, electronics are core part of car functions and instructors suggest to push the clutch in hard brakings to avoid the engine to shut off and consequently cut off electronics (like abs steering assist etc..) .
He didn't say you HAVE to press in the clutch in order to brake, it was more of a recommendation, I just think he worded it wrong, I think his point was you should press in your clutch so your engine doesn't suddenly feel the pressure of braking to a complete stop, you could just press in the clutch to separate your engine from the wheels, then brake.
"In manual transmission driving, BEFORE you press brake pedal, the clutch pedal must be pressed completely". That is what is said. There are people who do this and usually place the gear shift in neutral. This is WRONG! When braking, you can keep the car in top gear all the way to almost being stopped before you step on the clutch (before the engine stammers) OR downshift one, or more gears as you decelerate. When you are at a complete stop then you can place the shifter in neutral and let out the clutch pedal (relax your leg) The video describes driving a stick like an old woman.
Is it not equipped with synchronizers? If it is, by doing that, you are heating the synchronizers and f*cking them. If it's not, the clutch most be use just to start and to stop
You DO NOT have to press the clutch every time you want to brake in a manual car. You only press the clutch when you are going to stop completely (in speeds lower than ~20km). Furthermore, by applying the clutch before braking , it gets a little bit harder to stop the car since the car gets a little bit of extra speed! (because of the disengagement) - This video is only one of many videos created by 'professionals' which makes the mistake of 'always' pressing the clutch before applying the brake. I think this happens since they do not actually drive manual cars. Or, maybe this have been a claim of automatic gearbox manufacturers at the introduction of automatic gearboxes! Who knows?! :)) I personally prefer automatic gearboxes with the ability to change gears manually (tiptronic). Automatic gearbox is the best for city traffic (especially in cities built on hills), while the manual gearbox is the best option for enjoying driving in roads and rally.
engine braking is fine, but can be less efficient (in terms of fuel) then just depressing the clutch and using the brakes. You can, however, stop rather quickly.
Huh? In a carberated car, maybe. But in a computer controlled engine? Not true. At. All. The computer can shut off the fuel flow completely while slowing. However, if you disengage the clutch and let the engine idle, the computer fuels the engine. ;)
+TRLWNC1 is correct. In modern fuel injected cars, whether it be Gasoline MPI, GDI, or Diesel, when you let off of the accelerator all fuel injectors are turned off. This is why you should never take the car out of gear unless you are at a complete stop. That and it's safer to leave the car in gear.
@@joeseverythingchannel6564 "clutch pack" implies more than one clutch disc, and since manual transmissions use only one clutch disc that can not be referred to as a pack. Besides, the pictures are wrong. Work on learning before posting.
Actually the clutch pack includes the throw out bearing, pressure plate, friction plate (on flywheel applications where replaceable), and the clutch housing in the bell housing so eat it buddy do your research before responding
@@Iowa599 oh and fyi there are manual transmissions with upwards of 4 clutch disks in them its just that the most common stock clutches only have one. Most clutch upgrades include 2 or more clutch plates to increase the surface area of the friction material
You guys have to learn the working principles of planetary gears. Basically a planetary gear have 4 components, the sun gear (in the middle of everything) the ring gear (surrounding the planet gears) the planet gears (small 3 gears) and the carrier (connecting the 3 planetary gears) they're always in mesh, and by stopping one or two of these gears you get gear reduction, in which the speed in the output is different than the speed in the input, so you can get underdrive (speed is slower in the output), direct drive (output speed equals input speed) and overdrive (output speed is faster than input speed) that way you also multiply torque to get the car moving, that's why it's a lot easier to start in 1st gear than in 2nd gear, because torque is twice as strong (depending on ever gearbox and the gear reduction for the 1st gear of "X" gearbox)
It depends on the type of vehicle. A big godawful parent trap SUV/Pickup/minivan, sure. Automatic. Because it doesn't matter...the thing is a boat anyways. But any sort of sports car...even any sort of small or midsize sedan or coupe even...manual.
> manual transmission > step by step guide Oh I get that, this is nice > automatic transmission > AND THEN YOU JUST PUT A PART HERE AND ITS SIMPLE AND HERES ANOTHER PART AND WHEN WHAM BAM THANK YOU MA'AM LOOK IT WORKS Oh I'm lost now.
wiegje there's another video which fully explains about planetary gear automatic transmission. it's very complex tho. i still dont get it after watching second time. i guess im just not into cars
The basic idea is that a planetary gear allows a reduction in speed. Many of the original automatics were 2-speed. The planetary allowed the inside to spin for first gear, then went to the one-to-one when the planetary locks in. If you watch the video carefully, you can see how the central gear spins (and everything spins slowly around it) when the planetary is unlocked. The other thing that isn't shown well is that the output shaft is locked to the outside of the planetary assembly.
anos -v transmissions are very complicated, you can't get a complete grasp on them in an 8 minute video. in the tech school I went to in the navy, we learned several months worth of material on just transmissions in about a week and a half. of course due to costs and budgets, teaching us at the normal rate of a civilian school would cost to much and take too long. what I'm saying is that no matter how much they try to simplify transmissions, there is far too much to take in to grasp the complete concept of how these amazing mechanical wonders operate. and these aren't even complicated transmissions. the big ones that operate earth movers and semi tractor trucks are where it really blows your mind.
try understanding how gearing on a bicycle works.. that would be very helpful.. if u get the concept how those gears on a mountain bike or racer works, then u can move on to cars
That's why you drive for more than a week. Im far from an experienced driver and I rarely miss rev matches. Given like, another year of practice and I don't see myself missing any. Manuals also have a huge host of other advantages that I won't go into.
I have litreally never been in a manual car and had an experience that was as nice as a good automatic. You must be the best shifter in the world, or not. You and I don't define bumpy the same. Trust me, you miss more matches than you think. Over 200 rpms wrong and you can feel it quite a bit.
Christopher White its easy tho. getting going, you have to let go of the clutch as you step on the gas. same as shifting except you let go of the clutch instantly there. stopping tho, you have to keep your foot on the clutch in order not to stall it
Because a lot of people who drive sports cars are insecure and have a pathological need to feel superior to others, and a lot of sports cars have manual transmissions. It's just a way for them to feel better than other people because they possess a relatively unremarkable skill (i.e. the ability to drive a manual) that a lot of people don't bother with because there simply isn't much need to learn it in a country where most cars are automatics. Not knocking anyone who legitimately just prefers manual btw, just those who act like being able to drive manual (which isn't a hard thing to learn) makes them superior to other people.
Yeah I never said *everybody* who drives manual has an inferiority complex. I said *a lot* of people who drive sports cars (not everyone who drive sports cars) have an inferiority complex, and use the fact that they can drive manual to try and make themselves feel superior. Obviously some people simply prefer manual, and that's fine. I never claimed otherwise.
Hash Slinging Slasher American men are the only ones who say manual is for "real men." They just like to stroke their egos as much as they like to stroke their siblings' "gearticks."
It isn't hard the reason they brag is because they are rare in desirable cars like old muscle cars and if you go back even older it is actually difficult as they weren't synchronized
Durzin Sheldon Did you ever listen to a german talking about manual cars? Driving an automatic car is for pussies/ "unsporting". There are a lot of germans who think that automatic cars should be banned from streets...
Where is it being taken over? Where? Leave politics out of this you triggered uneducated dumbass drumpf loving minimum wage turd. Now fuck off...your break is over and the customers are waiting for their fries.
Ahh i wrote it just my opinion and a fact about my driving style,every person have opinion,did u have opinion too?lets share if u have. Auto and manual have many pros and cons Sorry for my bad english
Nice,but shifting transmision its more enjoyfull like a sportman :-D ,because we can set the speed and engine sound. No shifting like eat withouth drinking a water hehe
In order to shift as smooth as a automatic in a manual you need accelerate to the rpm you wish to shift at, lift your foot just a bit so you’re no longer accelerating but keeping constant, and then shift and complete a smooth clutch and accelerator exchange
Very good video, I believe another reason that Manual cars are seen as more fuel efficient is that the driver can anticipate the engine performance needs and shift accordingly. This keeps the car in a more ideal "rev range". This is most noticeable during hill driving and cornering. It is also why I am thankful my car has triptonic transmission. (It's an automatic gearbox, but I can "manually" shift up and down as needed).
Well, automatics have become smoother and more economical over the years, and manuals have become easier to shift, so let's call it a draw in terms of performance. On the other hand, automatics are easier to drive in rush hour, whilst manuals are more fun to drive on the open country road.
This has actually answered so many of my questions. Though the statement that the clutch must be fully depressed before braking is misleading. The clutch must be fully depressed before the wheels stop moving, I think it's generally preferable to keep the clutch engaged until that point.
Manuals are smoother than auto if you actually know how to drive, and you don't have to put the clutch in before you brake, who the fuck is naive enough to think that?
You don't have to, but why wouldn't you in most cases? If you're braking, most of the time, it's in preparation to stop, in which case you'll need to shift down, which requires the clutch to be in anyway. If you're merely referring to a slight deceleration, then no, it's not necessary to use the clutch, but for actually slowing down to a stop, or getting ready to take a corner, then pressing the clutch _is_ required.
Still not required BEFORE you break unless you are trying to go from 40mph to 5mph in 3 feet. The key part you are missing is the video says you must before breaking not before you stall the vehicle. It almost sounds like this person that made the video understands what a manual is but has never driven one.
Mia Ray I don't know if you have driven a standard (Manual) transmission in a truck before but in the manual of my truck it specifically says not to put the clutch in then breaking because disconnecting the engine from the drive train removes any breaking power the engine itself can provide. It is more effecient to down shift while using the break at the same time to slow down especially when a load is being hauled. The only time the clutch should be popped when stopped is to keep the engine from stalling.
I'd like to apologize for my previous comment. I spoke as though I knew what I was talking about, while in reality, I didn't. Directly after my post, I did a little research and quickly found that my logic, as sound as it was in my head, is simply not sound in the real world. While I love manual transmissions, and my in depth research into transmissions in general is almost solely on manuals, due to the sparsity of manual transmission vehicles at my disposal, I have very limited experience behind the wheel of them. So please forgive me for talking as though I knew what I was talking about. ^///^*
Ahh yes some nonsense only americans do, because using a manual transmission car a normal way, is too boring. Seriously Who the hell double clutcy and rev match????
@@anderstermansen130 I’m European and I do =D Got a cable operated throttle body, got that severed the other day, tied it up on spot and had the throttle pedal way higher than the brake... As a result, I wasn’t really able to double clutch heel-toe rev-match and I was pissed to no end
"when breaking clutch must be pressed with manual" - nope. theres engine breaking, which means just releasing the gas pedal. if you wanna use the brake you just should release the gas pedal. engine braking and brake-braking work together. when you STOP is when you need to press the clutch. please use "must" responsibly
I may have heard wrong, but he never says "when breaking, clutch must be pressed...", he says "before you press the break pedal, the clutch pedal must be pressed down completely". Two different things.
Eggpie_614 Plays ah cmon, manual is easy, when the rpm is high, just press the clutch pedal and move the gearshift, when the car is about braking, press the clutch pedal once again and finally move the gearshift backwards instead forward, like from 5 to 4 to 3 and so on until the car increasing the speed automatic cars is simple, just press the brake pedal and move the gearshift from p (or n) to d, and u can drive the car with one pedal, but notice, never sudden brake the automatic vehicles, espicially from high speed, because sudden brake can cause the engine to stall
pretty soon all cars will become self driving and all these kids won't ever have the experience of driving. that, in addition to the gig economy of uber and lyft, where you pretty much rely on others to do the driving for you. much like they no longer are taught cursive or how to properly make their signatures. many have atrocious handwriting skills and are dependent on their computers to create letters or notes that others can read. driving will become a lost art that only those born before 2000 will know or remember how to perform.
I have experience of driving with both of them. my advice: if you drive a lot in the city or somewhere that you have to change gear a lot, pick auto. otherwise manual is better from every aspect. if you become professional in driving you can even change manual without significant loose of converted power by controlling the clutch and fast gear changing.
Behrooz KHaleghi Rad i have tested both transmissions too. i prefer manual even in the cities. it provides good performance at low speed and more fuel efficient. it depends on the car too, but for me manual is better
I have them both with more than 10 years A/T experience, the automatic transmission (A/T) ones came from different generations, one has hill sensing and the other doesn't have one. I prefer automatic over manual transmission for highway and city commute because A/T is simpler to operate, I don't need to change gears, in a traffic stop just push the brake pedal, no need to change gears and my left hand is free to do other things, eating burger etc..lol. As of acceleration, for stop & go and highway driving, acceleration is almost instantaneously, the A/T will respond quickly adjusting its gear and pick up speed even if I push gas pedal at about 120-140 km/hour, leaving M/T car behind (You almost can't do this if you use M/T). The M/T is probably my preferred choice If my daily commute in a hilly area and need to overtake cars alot, M/T is more responsive than A/T.
The vast majority of cars in Europe are manual transmission and gear change becomes a smooth with experience. I drive both manual and Automatic, finding Automatic sluggish when it come to gear changes and jolts when doing so. I also found gear switching up and down repeatedly , when going up hills. In a manual you can hold the gear and increase the reves until you can have enough torque to hold the higher gear
The reason it won't be smooth is the driver. people don't understand the concept it is rough because the driver let's of the clutch before give a little gas or slamming off the clutch that is why it would be rough if you give a little gas while letting off its smooth shifting it takes practice like everything else
If im about to go up a hill ill shift down meanwhile if its automatic you'll need plenty of gas to make the hill meaning more gas usage . ill keep my standard
hey guys i know you you have done a lot of hard work on making this video i really appericiate your work this type of your animated video helps us a lot to understand the insight of the vehicals and many other machines which is normally very complicated
Daniel Tavares Ancient mentallity. Only to pose with your technical knowledge. Thinking about the future is smarter, which implies no transmission at all. Go electric. :-)
Please make a video on how to understand this video.
Tetea Chinzah 😂
Dyin
😂😂😂
Lol same 😂
Copy
Manual transmission - Ok. I see. Ah got it make sense.
Automatic transmission - which gear? What color? Release which what?
Right?
Automatic transmission works by magic... or it is operated by rodents. It just works!
yes of course.
Gear Crimson
I know right! Even while driving, it's like, hey, wait, what, how, why...will it stop now? Will it move? What's happening????
But, with a manual, it's like, yup, I got this... I know what needs to be done!
I always thought an automatic transmission would just be a manual transmission but shifting it automaticlly
Me too!
That’s a robotic transmission)
Cheaper cars have that, 3 motors to replace clutch and the two movements the stick would make
@@Pascaleiro that must be what my sister's little old Suzuki uses
FR
“This is why a manual transmission ride is never a smooth experience” and I took that personally
I get your point, but the fact is that an automatic will always be more comfortable than a manual, simply by how it works. But you're absolutely right, manual can be smooth too! It just requires more skill
Accept Jesus Christ ❤
@@huiba1 that's assuming the car is shifting well. I can shift better than the car I currently own. Though I guess it's mainly just your personal preference.
"Power shifting has entered the chat"
@@scottwesner9362 I daily an automatic, but got my license in a manual. And I agree! Some automatics shift horribly but modern ones are generally very smooth.
manual transmission: ok, makes sense
automatic transmission: *_IT'S WIZARDS_*
Hahahahahaha I'm dying from this comment
My brain went stack overflow on automatic gear
this is y robots will kill humans
The author should apply a link to the planetary transmission setup explanation video.
Also heavy loads are using automatic transmissions since there is not much place for human error. Especially computer-controlled automatic ones. I mean relatively heavy like for example a tank transmission. Another example can be a system in the "semi-trailer" truck.
It is true you can put more on smaller manual transmission but in this case, you have to rely more on the operator skills. Also, a heavy-duty manual transmission becomes rough to operate if the applied load is raised very high while the system weight, placement, and size limitations occur. It's more due to the simplified clutch than the transmission box itself.
What's most important is the system's live-cycle overall cost. It's sometimes even more important than the physics ;)
It's automagic
You forgot to mention that manual is also a free anti-theft mean in the States
And also you can roll start if your battery is dead
Or drive with the starter if your out of gas.
@@edgeofforever7720 how?
@@jettproductions6145 how to drive without battery lol
@@cautarepvp2079
You put the car in first gear and crank it.
You can also start the car by putting it in gear rolling the car and then "popping" the clutch
It's all nicely explained and I still don't know what the fuck is going on.
I also tried to understand, but I failed.
Eightosaurus Spelunk hehe none-car guys problem.
Jus Like That You need to learn to write.
Eightosaurus Spelunk it's typing and I'm pretty sure he did nothing wrong.
to make it easier to understand, u gotta start with bicycles.. if u see a mountain bike or racer (those with several gears) then that is the same concept... smallest sprocket on pedal+largest sprocket on rear wheel=1st gear... larger sprocket on pedal+smaller on rear wheel=higher gears.. u notice when bikers try to climb uphill they mostly use 1st gear, although it takes a lot of pedaling to move the rear wheel to one rotation, it is still bearable
same concept with cars... 1st gear is the slowest just like uphill on bike with low gear BUT its got power..but when u go faster u should use higher gears because at that point, inertia is your friend, and u dont waste your engine power
I prefer a manual. Better control (engine braking for example), smoother shifting (provided you know how to drive a vehicle with a manual transmission), and better fuel economy. Also I've had automatics that at certain speeds and loads couldn't decide between 3rd and 4th gear and kept shifting between the two giving you whiplash.
İ can engine break with my automatic. For amount of time i can set the gear i want for short periods by shifters behind wheel. Or i can make it completely manual
I'd prefer manual if I wanted to drive for fun, and an automatic if I wanted to drive without thinking too much. I think in the long run cruise control w/ an automatic transmission has been shown to actually have the best fuel economy, at least if you are on a highway and don't have to brake frequently or speed up of course. I just can't imagine spending 8 hours on a roadtrip with a manual transmission, but I guess thats why SUVs don't really have manuals.
@@yesyes-om1po Road trips are probably the easiest drive in a manual though. Just throw it into your highest gear once you get to speed and just keep cruising. It's the commute that can be rough in a manual, especially if you live somewhere with heavy stop and go traffic.
I get it old man new stuff is hard to understand sometimes but all the things you listed have been an advantage for automatics for the last 15 years
Yes I do agree with you. Because they say professional drivers knows how to uses manual transmission and does use it most of the time.
I just press and hold W on my keyboard to accelerate.
Same
Gamer Moment
How to get called a nerd in a nutshell lol
underated comment
Hahahahaha
you don't have to engage the clutch before breaking, that would lower the fuel efficiency. Press the clutch before the rpm get under the idle speed, that saves fuel and reduces the brake wear
Exactly!
@Dragneel Just engage the clutch when it's under 1000 rpm
@Dragneel dude, if you need to go from 100 to 0 in 5 secs, you should not press clutch man. Because you want to prevent an accident. Stalling your car is better than wrecking it
@Dragneel you don't, when you need to stop immediately just slam both pedals at once (emergency braking)
@@Agent-1220 yep both pedals decreases braking distance if the brakes get warm, you don't want to be having to stop the engine from spinning as well so disengage the clutch
"never a smooth experience"
I take that as an insult
Marko Djurdjevic or you.
@Marko Djurdjevic no u
@Marko Djurdjevic it always isn't smooth. You can minimize feeling of jaggong to unnoticeable level but you can't get rid of it.
@Marko Djurdjevic you don't understand. It isn't about skills. It is about technology. It is physically impossible to do not loss power while changing gear you can drive like God. You can use mechatronice to automate manual transmission to have perfect gear changing. But you will never get rid of it. You can only minimize feeling of it because car have big momentum. And no. In modern automatic transmission there is no gap between.
@Marko Djurdjevic you need to learn about engeenering and probably not about driving. Your knowledge of physics is not a related to how many kilometers you have traveled man.
As long I live in a region that gets snow, I will own a vehicle that has a manual transmission. There have been many times when I would have been hopelessly stuck if I had been driving an automatic. I was able to use the clutch and gas to "rock" the car out of a stuck spot. That probably shortens the life of the clutch, but it is better than being stuck in a snowstorm for hours or days.
If you're quick enough you can achieve this with an automatic too
Whether or not snow is a problem depends on the car itself and the tires. If that weren't the case sure some automatic shitbox would probably do a lot better in snow than an Iveco LMV
@Kaloyan Draganov Actually, it depends on whether people have any clue of what they are talking about. Obviously you don't.
@@LucidDreamer54321 It also depends if you are a larper who has driven an automatic once 20 years ago such as yourself. Do you even know how traction works?
@Kaloyan Draganov Do you even know how anything works?
I have new found respect for the people who have made the automobile what it is today.
Genius minds.
The Chiefs Thanks to the engineers at BMW,Ford,Mercedes and so on.
Automatic
@@whidoineedthis manual for life
Manual is good if one is paranoid of letting computers run the car though
No no no no. You do NOT press the clutch before applying the brake. The sequence is ABC: foot off Accelerator, foot on Brake, when nearly stopped depress Clutch. This is keeps the clutch engaged until the last minute and the car is better controlled. Pressing the clutch first results in a surge forward - acceleration of the car. I am a UK driving instructor.
Nicole K exactly, I was about to say that... disengaging the clutch reduces engine breaking, which we dont want trying to slow down
Engine braking is not only helpful for control, but for slowing the car! Never, EVER release the clutch unless you are downshifting to improve engine braking!
+TRLWNC1 The way I've always taught my pupils, is not to change gear at all when slowing down. Change gear when you have reached your target speed, or use the clutch just before the engine shows sign of being unhappy when stopping. Changing gear disengages the clutch and makes the car less stable during those moments.
Nicole K unless you are racing.... ;)
Nicole K but you are very correct.
My brain burned during the explanation of automatic transmission
Vule
Sane
It's not you. My cat could have meowed a clearer explanation.
Same dude
I tried to understand automatic transnission many times but understood nothing
Same, with automatic explanation my brain goes blank lol
The smoothness of the manual transmission is something that you learn with practice, so that can be a bit misleading information. In the other hand, it is recommended to have the engine engaged during breaking all the way before it starts to stall. By leaving the engine engaged you let your engine help you slow the vehicle down, saving a bit on breaks. I will also like to add that driving on downhills manual also helps to avoid the vehicle gaining too much speed, thus also not depending merely on break pads. Just saying…
The trade off then becomes how much wear you’re willing to put on your transmission. I prefer to just use my brakes since they’re easier to replace than a transmission. Definitely useful when going downhill though
Also I’ll add that you will use more gas using engine breaking and your engine will rev higher causing more wear and heat. I’ve decided that a brake pad job is easy enough than to stress my engine and clutch and trans. But for racing, engine brake is where it’s at.
@@BananaBabysthats just wrong, engine breaking doesn’t use any gas in injection engines
Only if you shift down while slowing down
@@tobiasbauer198 i mean yeah. If you don’t actually engine brake properly, it doesn’t save gas. But their statement was general.
You don't have to press the clutch pedal while breaking unless you are going too slow which causes the engine to stal
I think he meant braking until you stop, like when you get a red light.
@@BosisofSweden I believe Daniel's talking about 6:35. He says that you _must_ press the clutch pedal completely before braking, which is not really true.
When you're slowing to a stop you leave the clutch engaged to take advantage of engine braking. Obviously you disengage the clutch when you get to a near stop, but you can absolutely use the brakes while taking advantage of engine braking to decelerate to a stop. If you're familiar with heel-toe technique for downshifting while braking, that's exactly what's happening to slow the car down.
@@phone4189 aha, okay. Yes, that is incorrect.
That is what he meant though it was confusing lol. I think most people put it in N far before they have to fully stop.
@@danielplasencia7271 no, they don't. You gear down and motor brake if you have learned to do it the correct way. If you end up to have to stop you use no gear as you wait och the lowest gear with the clutch down if you are about to go
6:38 is nonsense. You can brake without engaging clutch, just watch rpm to dont drop below minimum to dont stall engine
Thats my man, at least someone mentions that.
yup and actually engine helps in breaking
He mentioned, "Heavy Duty Equipment"... When you have a "Heavy Duty Equipment" going down on a long hill or mountain, you don't want your brakes to overheat, so you use the transmission as an engine braking system...
@@ImranQureshi-ig9kd only if you downshift
@@g0nzal0id the downshift is the immediate break , i m talking about engine break that u will feel if u release the race , the car will slow down , if u press the clutch u l see that the car slowing down isnt as quick as it would be without the clutch meaning the engine is stopping the car while in gear
The people that invented these things are geniuses.
I'd love to see a similar video about electric car engines. Would the automatic gear system be the same?
An electric car dont need to shift gears as the 3 phase VFD controlled motor in modern electric cars operate between 0 to 7-8000 rpm with no problem while an internal combustion engine works best between 800 - 3000 rpm, hence the need for many gears to keep the engine in that speed range. Also the tourque is at max at a certain rpm for a combustion engine unlike the electric motor wich have 100 % torque from 0 rpm through its entire speed range.
Thank you for the awesome reply. We are going to explain all these things in our electric car video.
Learn Engineering Fantastic! Cheers to everyone making these videos. I love how clean, detail, professional and informative they are. You guys are awesome. :D
Most hybrid and electric cars use a CVT (continuously variable transmission). Which basically means that you don't have SET gear ratios. What happens is that the gear ratio gradually changes as you go faster, so as you accelerate lightly, the RPMS will stay somewhat in one place. If you Floor the gas pedal, the transmission will hold onto a lower gear ratio for longer to get that better acceleration. The simplest explanation I can give you is this: Picture a large cone shaped object, then picture a belt riding on that cone and attached to the transmission output. The gear ratios change by sliding that belt back and forth on that cone. It's like a bicycle, the bigger gears on the crank will give you higher ratios, and when the chain gets put on a smaller gear, the gear ratio becomes lower. The only fundamental difference between that and a CVT is that the CONE shape allows the belt (or chain) to slide up and down gradually, changing the ratio. Hope that answers your question!
Shadow Heart the answer would be no, most electric cars have direct drive, wich means no gears, no shifting. this is because an electric motor is not limited to a specific range of rpm like gas engines. they are much simpler with far less moving parts. they can deliver power to the wheels over a much wider range of motor speeds.
honestly, as much as traffic makes me wish i had an automatic transmission (seriously, operating the clutch and constant swapping between the 1st and 2nd gear is a nightmare)
i have to say, that in almost every other non-traffic situation, manual transmission is pure joy
you basically feel every single move you make
you can rev the engine if you want
you feel the sudden surge of power when you change the gear and quickly release the clutch pedal while revving the engine
i honestly recommend everyone to try the manual transmission at least a few times if it's possible
If you care about your transmission, you shouldn't release the clutch pedal too fast.
As the video explained, the Synchronizer Ring is matching the speeds, but if you release too fast, it doesn't have the time to actually do its work and as such tear a lot more.
And well, repairing a transmission is pretty costly.
@@kuhluhOG i agree, and by "quickly" i didnt really mean "instantly"
the sole feeling of sudden sharp shaking is probably enough to make most people understand that
also if you rev the engine enough before releasing, it will fit in just perfectly
@@Rolsig automatic : 8--D manual : 8------------D
I would reccomend people trying automatic at least once.. manual is manual and you feel the car and really handy on ice starting from second gear or in adding torque in corners playing with right leg.. it is the way to drive a car for millions of reasons. Automatic won't make a proper driver out of someone. Name me one car racer that drives automatic?
@@BushcraftEurope well, Formula 1 cars have a sequential half-automatic transmission
meaning: 7 forward gears (+ neutral + 1 backwards), they can only switch to gears next to the current one and not too fast, they don't have a traction interruption and they only choose which gear the car should be in (the rest is done by the software)
This automatic trans gave me the “missile knows where it is because it knows where it isn’t” vibes
Dead
@@thatonehobgoblin3992 omg lol lmao frappucino, im dying sistaaaaaaaaa
@@HowToTouch omq deadass yass queen no cap
ua-cam.com/video/_LjN3UclYzU/v-deo.html
@@Broken_Orbital lmao nice
"before braking, the clutch pedal must be pressed completely" - I bet every driving instructor on the planet want's to have a word right about now.
hahahahaha
Its much more easier to press the clutch and then press the brake
Why the hell they make us do the opposite
@@mangixbrew1 To use the engine to help slow down. You even get warning signs on long downhill stretches to do this instead of braking constantly.
@@Henk14789 when my dad was teaching me to drive he told me about engine breaking and how good it is. He also added: clutches are more expensive than brake pads. 😂 Use your brakes to brake people, don't engine brake.
@@BennyJ69 Using engine brake doesnt signal following traffic that you are braking, this is good reasons to use the brakes.
@@groundloss Engine braking is good for when you have a long enough distance to go, or if you need to slow down faster than just letting go of the gas. Traffic behind you should have enough time to see you slowing down even without the brake lights--assuming they're not distracted by playing on their phones... And your engine can handle shifting back into a lower gear just fine, assuming you don't skip gears. Your brake pads will wear down a lot faster if you exclusively use brakes.
“You can see that an automatic gear set has two inputs, and one output”
No I don’t lol
Bro made video for blind peoples 💀
At 3:28 “A manual gear drive is never a smooth experience.” WRONG! It depends on the driver and how long that person has been driving a specific vehicle. The trip can potentially be as smooth as with an automatic transmission. In my case for example, I have been complimented by passengers who say they often can’t tell when I am shifting except for the fact that they see my hand move.
I just watched a 1936 video about differentials... I understood it. It was 6 minutes, I know how differentials work now. No idea how transmissions work. Maybe the 1930’s have another video.
People that time, were simple.
There is a 1930s video on transmissions. I think it was called levers or something. I think this video expects you to have basic knowledge on mechanisms (such as planetary gears) whereas older videos go over more, albeit to less depth.
Just came from the 1938 Chevy one about suspension lol
"Spinning Levers" short film by Chevrolet made around 1936.
It is on YT.
VERY informative.
The channel name is 'US Auto Industry', for easily understanding these concepts.
Dear patrons
Sorry, I couldn't publish your name/photo toward the end of this video. The climax scene of this video was filled with so much information that there was no space left to display your name. Sorry for that. I will show your name/photo from the next video onward. Thank you for your continued support.
Learn Engineering mate that's why we love manual that "variation of speeds" helps a lot in mountain road or in a drift course so in other words auto is good for inexperienced drivers to go from point a to b (sub humans) and manual is for much more experienced people (car guys/petroheads) who love the turns on a mountain or a racetrack 😉
Learn Engineering Please make a video regarding working of carburetor and fuel injection system .
Thank-you
Learn Engineering except drag racing where autos dominate
stevemic drag racing is only for cars corners are for drivers tho ;)
HH E I hope, you are taking about AMT. They are just computer controlled manual transmissions. They have all the drawbacks of the manual transmissions.
automatic? you mean lazy mode
More like easy mode:)
I see God
Didn’t expect to see you here. I agree. Automatic is for western spy’s and pussys
GREETINGS THE SHASHLIK KING
i dont read replies “I press da pedal and da ka goes VROOM! Pulling stick is too hard for me, me American, me vote Trump!”
Best video I have ever seen talking about how manual gear box works .... great work
6:39 "Before you press the brake pedal, you have to press the clutch pedal" So wrong.. You should brake with the engine engaged until you almost reach idle rpm's, then press the clutch and brake further. That way you both save the brakes as well as the car's computer knows you're braking on the engine so it won't inject fuel = better milage and lower emissions.
But not until the engine stalls which is a risk if you brake from a high gear into a low speed.
When you drive manual you quickly get used to disengaging the clutch at the right time for the current gear. Also, this is not directed at these two comments, but the video also said that a manual is never smooth. Which is also wrong, you can achieve a smooth shift. EDIT - It can be smoother than any auto I've driven so far.
Johann Kuhn
Yes, but quite frankly it's very difficult to ALWAYS shift smoothly in a manual. There will almost always be some jerking at one point or another, especially if the engine's cold.
Makes sense.
Johann Kuhn
Yet, I prefer a manual. :)
"it might seem like a simple mechanism"
L M not at all.
Reminds of all of the college textbooks that said "This is trivial and we leave it an an exercise for the reader." Like nah bruh , help me!
lol nope.
Yeah, not THAT simple, but then I saw how the automatic transmission worked and that was way, way more complicated.
LOL!!!
Something not mentioned - automatic has a noticable and significant lag in it. In a manual, when you step on the throttle, since you are mechanically connected to the transmission, power delivery is instant. In an auto, it takes a small bit of time for the torque converter to begin pushing the transmission forward. Then, if there is any shifting occuring, there is a significant lag before full acceleration.
Manuals, assuming you know how to properly drive one, acceleration is again, nearly instantaneous.
Yes. And there are chipsets that can speed up this process. I have one installed on my Chevrolet S-10 2018 and the difference is noticeable when you need power to overtake someone in the road or for going from a stationary position to instantly high acceleration. I would say is a must have for safety purposes since your car becomes much more responsive when needed.
shift bog is real on cars though. bmw e92 n54 has a really long shift bog
We have a hybrid Mini Countryman that seems to have solved this problem. The eletric motor provides instant torque.
Two ways to resolve this (I've tried both, they work): 1) use so-called SPORT mode, it forces AT to shift down when you slam that pedal and has a significantly less reaction time compared to regular AT mode; 2) modern AT have a kick-down, which activates when you push the accelerator down to the floor and then some (you'll feel the bump when you press it enough), that'll force AT to give maximum power at the current gear, but be careful not to overrev the engine.
There's also a third way, which is manual shifting, but I haven't tried this on the road yet, so can't recommend.
@@Nero_PR never realized Chevrolet released the S-10 in '18
very clear it helped me understand how gear selection works, cause i really had trouble understanding how it didn't just go at one speed at all times but the visual helped so much thanks
Tesla drivers: what's a transmission
Sonic557 automatic d and r
ACTUALY ANOTHER SCEANario!!!!!!!!
Widow: why my husband got burnt in tesla and i have to pay still for his stupuid car !!!!!!!
Sonic557
Tesla Drivers “ I LiKe BiScUiTs” 🤪
@crummyy no they don't. The motor is directly coupled to the wheels tharough a single gair pair and deferential. The motor doesn't stall at low speeds like an IC engine would so you don't need to disconnect it from the wheels
@00rphb get off your high horse
6:01 my man just went from first gear to fifth
haha yes big brain
Nice spot
He fried 2nd 3rd and 4th gear showing everyone how they work so now he has to redline 1st gear and feather 5th to get up to speed
It's reverse not the fifth gear
He was a movie character
"Let me introduce another planetary set that you still don't understand to explain how this is achieved. The output of the second planetary set is attached to the input of the first. It's simple!"
....
Pretty much always with the videos this channel uploads. They pop up in my feed as some kind of intellectual exercise where you have to google things elsewhere to understand them. These videos merely introduce the concept for me.
I understood it but I've worked on planetaries. Each stage it a multiplier and it just depends on how they add up depending on the power path.
@@timjohnson1199 Speak english doc, i aint a scientist.
@@Inferamusic Each stage of the planetary is sort of like a separate gearbox. So, each stage gets multiplied by the other. If 3:1 and the next stage is at 2:1 the output will be 6:1, or, if you have 1000 rpm coming in you'll have 6000 rpm going out.
There is a 1930's video. Watch it. It's a thousand times better than this one.
This is legit the only video that made me understand this thing and i had seen like over 30 the past year and never got it till now
3:26
"Never A Smooth expierence"
My father who is driving manual for 25 years:
Am i A joke to you?
he mean, when you need to shift your gear you have to push clutch pedal so at this moment engine not turning wheels.
Fucking moron. Everytime you press the clutch in you stop putting power to the wheels, they even showed this in a graph
@@AzzaYaDog i think artur is mentioning about how some new drivers may make the body of the car make a tugging feeling because they dont switch gears smoothly or dont rev match to make a smooth transition, where as experienced manual drivers make it seem like there is no tugging by doing rev matches and smooth clutch engagements, hes not talking bout power not going to wheels
It is probably hard if you plan on parking up a upward road. Considering the car have to clutch up if you mess it up
Your father doesn't drive smoothly 😔
Driving Manual is very smooth too. Depends who's driving. The same for automatic.
I can drive my manual very smooth
the point is even if it toke you .25 of a second, you still lose power from the engine in Manual gear, while the automatic gear never lose power from engine.
💯
@@khaled00962 he said smooth not power
@@khaled00962 still you can just turn the engine high enough and then switch into the next gear very smooth so you won´t jerk at all (sry i speak german xD)
Manual is never smooth? I dare say my shifting is smooth as butter sir!
Guts Puck hmm. A wild Berserk fan appears.
I think its said for beginners 😂
Same here. every car I have ever owned over the last 28 years was a manual.
I shift without even thinking and it's very smooth.
It’s relatively less smooth than automatic transmissions.
I felt personally attacked when he said never
6:36 That's one of the biggest mistakes. You never disconnect the engine, by doing so on a downhill slope momentum can really take your car. Engine braking is used combined with braking. Never disengage the clutch unless you're ready to stop completely. When you want to go slower, just go to a lower gear. Also on downhills, it's better to be in gear and using the brake to have almost no fuel consumption.
I thought I was the only one who noticed it.
The use of clutch while breaking is to prevent the engine coming to a halt while in gear, or in a complete stop, only.
They demonstrated it very poorly unfortunately. Engine braking is a well known and well used practice in cars with manual transmissions and fuel injection systems.
Types of engine braking:
VVVVVRRRRrrrrrrrrrrr
bdbbdbdbdrrrr (whoshhhhhhhhhhhhhhhhhhhhh)
@@bradyn4212 lol. Thats jake braking, different mechanism for slowing down a vehicle,
@@theedgarthefish4267 Yes an the second one with the woshhh would be an exhaust brake (on certain engines and vehicles it makes a hissing noise) and yeah I think they're technically still forms of engine braking, just diesels don't brake well on their own without mechanisms
Understood Nothing :')
BUT it was fascinating to watch, isn't it? :D
Exactly xP
haha me too.I tryed to understand tho.
Yeah XD I don't Even Know How To Drive :P
why do you write like that
You definitely don’t have to engage the clutch in order to break in a manual
I belive it refers to when you break to a critical low RPM or when you want to stop.
Cameron, let it slide.. video most probably made by a 'murican who never drove stick. You've seen the graph? What moron can't drive stick smooth as babyoil? Then I remember, manual transmission is the best anti theft system in the US
@@3goats1coat haha i mean you lose power when you change gears ether way . there is a reason why automatics shift faster and better. but manual is so much more enjoyable exactly that "loss in power" is so much fun when you press gass a bit then change gear and you feel car tug forward damn that is exiting.
@@luk4s56 well, you lose traction for less than a second and more than a ton of steel being in freeroll.. you get what I mean, there's literally no way for a passenger with closed eyes to feel when you shift (except if you want to).
Also, there's a reason why drift and rally both use manual. You're losing a lot of control over your car for that bit of comfort. Also safety, I'd say (considering tight overtakes).. the knockdown needs an eternity to activate, with manual you can be at 4k RPM with a howling turbo in a split second.
@@3goats1coat true i agree. its just that auto is more convenient. thats all there is but also i think its good that auto is popular. inexperienced drivers with manual are terifying to meet on a road
I've driven both manual and automatic, and I'm so happy II know how to drive manual and have a manual car, it is so much more enjoyable.
Misha Sleptsov There are no big traffic jams where I live, and they don't last longer than 1 - 2 hours, so it is really lovely!
Manuals are fun when the car has some power, but the manuals I've driver were low powered cars, so it wasn't really any fun.
+Flix
You are really lucky. where i live its traffic jams, frequent lights and constant up and down slopes.
It is a nightmare. CVT is the best choice where i live.
Misha Sleptsov... ah, driving stick for experienced drivers becomes so 2nd nature that it doesn't matter in a traffic jam, you don't think about it one bit...
Whats enjoyable about having to cancer around with the gears? Yeah you have better control, but for what? Most people can't even deal with that and switch gears too late and just waste fuel.
Understanding the mechanisms behind manual transmission is very helpful in learning to drive it.
Dear friends, Please support us at Patreon so that we can achieve the goal of 2 video release/month.
www.patreon.com/LearnEngineering
Learn Engineering
Learn Engineering Dear Learn Engineering,
Will these principles covered in the video be taught generally in automotive engineering courses in university?
Learn Engineering This video was very interesting. I am studying mechanical engineering in university and i am hoping to get into the automotive field. Thank You Learn Engineering for the depth explanation :)
Chechnyan Martyr I & Milk Video Milk Video Milk Video Milk Video Milk Video ass
Keith C hungry what?
Actually you don’t have to engage the clutch in order to brake. It just makes the transition of shifting down smoother. The clutch only has to be engaged when you’re stopped
If you downshift you should double clutch or rev match to prevent wear on the transmission.
@@theedgarthefish4267 only when driving antique without syncro or racing. Definetly not needed on normal traffic
@@tomzu8848 You don't have to do it, bur rev matching when downshifting reduces strain and wear and tear on the clutch assembly and transmission. Downshifting without revmatching forces the transmission into a braking type action which is not what it was designed for
@@theedgarthefish4267 strain and wear without rev matching on normal driving is so minimal it doesn't eat transmissions lifespan lot. Unless it's some glassbox that has been poorly manufactored/designed.
@@tomzu8848 what you're saying is true....but personally, rev-matching is more fun, when done right 👌
Wow this video made me understand transmissions less
For years, only thing I didn’t understand at least a little bit on cars, was transmissions, now I do, thanks
Anyone else understand the manual but not the automatic?
Same
Same and I can usually easily understand things
Me. Ever hear of Porsche's 1970s Sportomatic? Just a manual with auto-clutch. They've had tiptrontic..no full autos for them!
@Gabriel you're on drugs
after 3 years of mechanical engineering i think i finally got it
ehhh
you can have a smooth driving experience in manual too...
and you dont need to disengage the clutch in order to slow down
This video is too oversimplified. EIDT: I do not want to say that I dislike the video. But this topic is actually way more complicated. This video gives a nice and well animated introduction and those who want to learn more can do so. I encourage anyone to do it.
Which video would you suggest that does not oversimplify? Also: can you point out at least a few points where it oversimplifies. I am not doubting you, on the contrary. I am learning, so I am really curious to understand that.
Cláudio Sampaio
I recommend starting with Wiki:
en.wikipedia.org/wiki/Manual_transmission
and
en.wikipedia.org/wiki/Automatic_transmission
The fluid coupling, also used in this video, is a part of many automatic transmission systems. Contrary to a clutch, it will always exhibit some level of slip and cannot completely "disconnect" the transmission from the engine either. Buses usually have a torque converter, which needs even more power to run but offers smoothness over efficiency, making diesel run busses accelerate equally like electric trolley buses. There are other transmission designs like the two clutch DSG automatic transmission which does not have a fluid coupling or torque converter, but even this type has its flaws (like when you decide to change from acceleration to braking or from motor braking to acceleration at the time of the transmission changing gears. Even this description is oversimplified.
Cláudio Sampaio one big problem is that this video shows the automatic as a superior transmission
the thing is that, if you are good at it, you can shift quicker with a normal (manual) than with an automatic. also the atomatic is way heavier than a manual
good thing about the auto is that you dont need 2 hand and 2 feet to drive it
most of the bolids are automatic , deal with this
dude....who's the genius in making these transmissions...complicated af
engineers lol
Chill, all he said was that it was confusing and the people who made these transmissions are smart
Its not confusing now they have been awhile you ass hat. All he said was the people to originally come up with this are smart. Now stfu and get off your high horse.
Years and years of projecting the and re-projecting it, results in a more complex mechanism, if you're new to this engineering stuff I'm not surprised that you'll not understand it from the beginning.
Leafeon Aliens
"this is why manual transmission is never a smooth experience" yeah, if you're too lazy to get it right
lol newer cars with automatic slip too, or the computer is being dumb
Did he talk about anything you feel or was he talking about the speed curve? Very obvious the curve was the topic in that statement.
@@felipepubillones2768 yeah I know lol
6:40 NO! you don't need to press the clutch in order to brake!
brake not break. apart from that, i agree, press if braking in order to stop not to slow down. otherwise you loose inertial engine brake and you will end overheating the brakes. but on today cars, electronics are core part of car functions and instructors suggest to push the clutch in hard brakings to avoid the engine to shut off and consequently cut off electronics (like abs steering assist etc..) .
He didn't say you HAVE to press in the clutch in order to brake, it was more of a recommendation, I just think he worded it wrong, I think his point was you should press in your clutch so your engine doesn't suddenly feel the pressure of braking to a complete stop, you could just press in the clutch to separate your engine from the wheels, then brake.
I know! WTF kinda idiot made this crap!
"In manual transmission driving, BEFORE you press brake pedal, the clutch pedal must be pressed completely".
That is what is said.
There are people who do this and usually place the gear shift in neutral.
This is WRONG!
When braking, you can keep the car in top gear all the way to almost being stopped before you step on the clutch (before the engine stammers) OR downshift one, or more gears as you decelerate.
When you are at a complete stop then you can place the shifter in neutral and let out the clutch pedal (relax your leg)
The video describes driving a stick like an old woman.
Placing the gear shift to neutral before stop is normal.
"Every time you need to change the gear, you must disengage the clutch"
*Me, a truck driver* Floats everything past 2nd
I drive a Jetta and I don’t use clutch past 2nd
Is it not equipped with synchronizers? If it is, by doing that, you are heating the synchronizers and f*cking them. If it's not, the clutch most be use just to start and to stop
I worked in a tractor that didn't had synchronizers, you only can get the gear shifting correctly, not grinding, if you don't use the clutch
@@jackh1577 be careful with your synchronizers
Do you also float everything future second gear or is it just past?
You DO NOT have to press the clutch every time you want to brake in a manual car. You only press the clutch when you are going to stop completely (in speeds lower than ~20km). Furthermore, by applying the clutch before braking , it gets a little bit harder to stop the car since the car gets a little bit of extra speed! (because of the disengagement)
- This video is only one of many videos created by 'professionals' which makes the mistake of 'always' pressing the clutch before applying the brake. I think this happens since they do not actually drive manual cars. Or, maybe this have been a claim of automatic gearbox manufacturers at the introduction of automatic gearboxes! Who knows?! :))
I personally prefer automatic gearboxes with the ability to change gears manually (tiptronic). Automatic gearbox is the best for city traffic (especially in cities built on hills), while the manual gearbox is the best option for enjoying driving in roads and rally.
These guys are engineers, not professional drivers. I don't mind if they make a mistake about driving, as long as they explain the mechanism well
engine braking is fine, but can be less efficient (in terms of fuel) then just depressing the clutch and using the brakes. You can, however, stop rather quickly.
Huh? In a carberated car, maybe. But in a computer controlled engine? Not true. At. All. The computer can shut off the fuel flow completely while slowing.
However, if you disengage the clutch and let the engine idle, the computer fuels the engine. ;)
+TRLWNC1 is correct. In modern fuel injected cars, whether it be Gasoline MPI, GDI, or Diesel, when you let off of the accelerator all fuel injectors are turned off. This is why you should never take the car out of gear unless you are at a complete stop. That and it's safer to leave the car in gear.
the thing u say is about driving, the thing in told video is about mechanism. both are right in its own.
Corrections:
Manual transmissions (in cars) use a clutch disc, not a clutch pack. An automatic transmission has several clutch packs, like pictured.
Its actually called a clutch pack in a manual transmission
@@joeseverythingchannel6564 "clutch pack" implies more than one clutch disc, and since manual transmissions use only one clutch disc that can not be referred to as a pack.
Besides, the pictures are wrong.
Work on learning before posting.
Actually the clutch pack includes the throw out bearing, pressure plate, friction plate (on flywheel applications where replaceable), and the clutch housing in the bell housing so eat it buddy do your research before responding
@@Iowa599 oh and fyi there are manual transmissions with upwards of 4 clutch disks in them its just that the most common stock clutches only have one. Most clutch upgrades include 2 or more clutch plates to increase the surface area of the friction material
Manual is very easy to understand, but the Automatic transmission I still don't have a damn clue wtf is happening in that.
RzVids true
RzVids lol true. it's fluid in motion. but it's complifuckincated
This is really me now.
Hats off to the engineers who designed it...
You guys have to learn the working principles of planetary gears. Basically a planetary gear have 4 components, the sun gear (in the middle of everything) the ring gear (surrounding the planet gears) the planet gears (small 3 gears) and the carrier (connecting the 3 planetary gears) they're always in mesh, and by stopping one or two of these gears you get gear reduction, in which the speed in the output is different than the speed in the input, so you can get underdrive (speed is slower in the output), direct drive (output speed equals input speed) and overdrive (output speed is faster than input speed) that way you also multiply torque to get the car moving, that's why it's a lot easier to start in 1st gear than in 2nd gear, because torque is twice as strong (depending on ever gearbox and the gear reduction for the 1st gear of "X" gearbox)
Thank You Engineers.
Your ingenuity is appreciated.
In all seriousness, it’s a factory problem, if they say they want it cheap we’ll make it cheap.
I'm pretty sure that this video was made in us
Who's us
@@saucybaka4439 U.S
this accent is a U.S. accent, but I have a feeling that's not what you're talking about.
@@saucybaka4439 the UNITED STATES
It's indian
Before I see any mistake made in the video;first I appreciate his time and efforts made...
look, by far manuals are way more fun to drive, but day to day...especially in any kind of traffic, automatics are very convenient.
It depends on the type of vehicle. A big godawful parent trap SUV/Pickup/minivan, sure. Automatic. Because it doesn't matter...the thing is a boat anyways. But any sort of sports car...even any sort of small or midsize sedan or coupe even...manual.
@Tom R City traffic in a manual? Starting and stopping over and over?
@@Eli-gn6dr yes
@@Eli-gn6dr i like manual...cuz its easy..and i like to have control over my shit
@@system8877 so u say that with an automatic u dont have any control over the car?
> manual transmission
> step by step guide
Oh I get that, this is nice
> automatic transmission
> AND THEN YOU JUST PUT A PART HERE AND ITS SIMPLE AND HERES ANOTHER PART AND WHEN WHAM BAM THANK YOU MA'AM LOOK IT WORKS
Oh I'm lost now.
wiegje there's another video which fully explains about planetary gear automatic transmission. it's very complex tho. i still dont get it after watching second time. i guess im just not into cars
Look for kinematic guides and you'll get it ;)
The basic idea is that a planetary gear allows a reduction in speed. Many of the original automatics were 2-speed. The planetary allowed the inside to spin for first gear, then went to the one-to-one when the planetary locks in.
If you watch the video carefully, you can see how the central gear spins (and everything spins slowly around it) when the planetary is unlocked.
The other thing that isn't shown well is that the output shaft is locked to the outside of the planetary assembly.
Gud reddit meme arrows friend. Upvoted
Dr. Pavel I'm CIA nice trollbait. 11/10 would bait again
i dont know why it so hard to me to understand !! but in other hand thanks for this video 🙂
Lulușa Armand but its so fast
i think if he show us the transmission slowly we will understanded 🙂
anos -v transmissions are very complicated, you can't get a complete grasp on them in an 8 minute video. in the tech school I went to in the navy, we learned several months worth of material on just transmissions in about a week and a half. of course due to costs and budgets, teaching us at the normal rate of a civilian school would cost to much and take too long. what I'm saying is that no matter how much they try to simplify transmissions, there is far too much to take in to grasp the complete concept of how these amazing mechanical wonders operate. and these aren't even complicated transmissions. the big ones that operate earth movers and semi tractor trucks are where it really blows your mind.
Christopher Williams ah thats why i dont get a shit what the video is trying to explain. i think im too dumb for engineering
Muhammad Shafiq no way dude, just about anyone can learn it. now practical and real world applications though, that's a whole other ball game.
try understanding how gearing on a bicycle works.. that would be very helpful.. if u get the concept how those gears on a mountain bike or racer works, then u can move on to cars
I know ALOT about cars.. But this video made me forget which was a bolt turns
Why am i watching this? I dont have a car
Josh Groban Same
Josh Groban because you like to know how things works
I want to build my own car and be original
I know it is difficult for you, but wasn't there a reverse on a Learjet as well?!
Josh Groban fuck off
Manuals can be a smooth experience you just have to rev match.
You will not hit rev matches as often as an automatic. Also when you fail, it is even more bumpy.
That's why you drive for more than a week. Im far from an experienced driver and I rarely miss rev matches. Given like, another year of practice and I don't see myself missing any.
Manuals also have a huge host of other advantages that I won't go into.
I have litreally never been in a manual car and had an experience that was as nice as a good automatic. You must be the best shifter in the world, or not. You and I don't define bumpy the same. Trust me, you miss more matches than you think. Over 200 rpms wrong and you can feel it quite a bit.
Maybe you're just the worst shifter in the world.
I know for a fact that you can not shift as smooth as a new automatic and as consistently... But yeah, you are probably the best driver in the world.
Why are everybody hating manual or automatic it just a tranmission
that makes me cringe
because it's the internet and some people have nothing better to do with their lives
Christopher White its easy tho. getting going, you have to let go of the clutch as you step on the gas. same as shifting except you let go of the clutch instantly there. stopping tho, you have to keep your foot on the clutch in order not to stall it
Because a lot of people who drive sports cars are insecure and have a pathological need to feel superior to others, and a lot of sports cars have manual transmissions. It's just a way for them to feel better than other people because they possess a relatively unremarkable skill (i.e. the ability to drive a manual) that a lot of people don't bother with because there simply isn't much need to learn it in a country where most cars are automatics.
Not knocking anyone who legitimately just prefers manual btw, just those who act like being able to drive manual (which isn't a hard thing to learn) makes them superior to other people.
Yeah I never said *everybody* who drives manual has an inferiority complex. I said *a lot* of people who drive sports cars (not everyone who drive sports cars) have an inferiority complex, and use the fact that they can drive manual to try and make themselves feel superior. Obviously some people simply prefer manual, and that's fine. I never claimed otherwise.
Thanks
Love this channel, you guys need to team up with engineering explained.
Exactly
Exactly.
Exactly.
Exactly
No need for American men to brag about driving a manual; almost all of the cars in Europe are manual. So old grandmas drive manual in Europe too.
Hash Slinging Slasher American men are the only ones who say manual is for "real men." They just like to stroke their egos as much as they like to stroke their siblings' "gearticks."
It isn't hard the reason they brag is because they are rare in desirable cars like old muscle cars and if you go back even older it is actually difficult as they weren't synchronized
Durzin Sheldon
Did you ever listen to a german talking about manual cars?
Driving an automatic car is for pussies/ "unsporting".
There are a lot of germans who think that automatic cars should be banned from streets...
True I don't know anyone that owns a auto, even my nan drives manual
Where is it being taken over? Where? Leave politics out of this you triggered uneducated dumbass drumpf loving minimum wage turd.
Now fuck off...your break is over and the customers are waiting for their fries.
Don't ever stop uploading videos.... Really appreciate the work you do..
As a mechanic, this explanation was all over the fuckin place.
vote manual transmission
more controll and more safety
dafuq ? How the f is manual safer?
Ahh i wrote it just my opinion and a fact about my driving style,every person have opinion,did u have opinion too?lets share if u have. Auto and manual have many pros and cons
Sorry for my bad english
My opinion is auto,i mean you can just drive around chilling,dont need to shift gears
P.S my opinion
+TheRealMonster engine brake is stronger, you are less likely to mistakenly press the gas pedal when you are supposed and wanted to brake
Nice,but shifting transmision its more enjoyfull like a sportman :-D ,because we can set the speed and engine sound. No shifting like eat withouth drinking a water hehe
i have an automatic suv, and a manual pickup truck, just watched the whole thing, i still dont know how either work 😂. nice vid though 🖒
In order to shift as smooth as a automatic in a manual you need accelerate to the rpm you wish to shift at, lift your foot just a bit so you’re no longer accelerating but keeping constant, and then shift and complete a smooth clutch and accelerator exchange
Wow sounds 1984
Its super easy, i learned when i as 9 in a 1995 ford ranger. No matter how old as long as you know what youre doin stickshift is smooth as butter
..... it's all about the 'feel'.....being one with the vehicle...
>t Never drove an automatic
Very good video, I believe another reason that Manual cars are seen as more fuel efficient is that the driver can anticipate the engine performance needs and shift accordingly. This keeps the car in a more ideal "rev range".
This is most noticeable during hill driving and cornering. It is also why I am thankful my car has triptonic transmission. (It's an automatic gearbox, but I can "manually" shift up and down as needed).
Manual: "Huh, simple, I understand everything."
Automatic: "WHAT IS THIS WITCHCRAFT?!"
Well, automatics have become smoother and more economical over the years, and manuals have become easier to shift, so let's call it a draw in terms of performance.
On the other hand, automatics are easier to drive in rush hour, whilst manuals are more fun to drive on the open country road.
Your animation is amazing, I am an engineer and I never saw an explanation about transmissions that clear before. Good job! 👍👍👍
This has actually answered so many of my questions. Though the statement that the clutch must be fully depressed before braking is misleading. The clutch must be fully depressed before the wheels stop moving, I think it's generally preferable to keep the clutch engaged until that point.
Manuals are smoother than auto if you actually know how to drive, and you don't have to put the clutch in before you brake, who the fuck is naive enough to think that?
You don't have to, but why wouldn't you in most cases? If you're braking, most of the time, it's in preparation to stop, in which case you'll need to shift down, which requires the clutch to be in anyway. If you're merely referring to a slight deceleration, then no, it's not necessary to use the clutch, but for actually slowing down to a stop, or getting ready to take a corner, then pressing the clutch _is_ required.
Still not required BEFORE you break unless you are trying to go from 40mph to 5mph in 3 feet. The key part you are missing is the video says you must before breaking not before you stall the vehicle. It almost sounds like this person that made the video understands what a manual is but has never driven one.
Mia Ray I don't know if you have driven a standard (Manual) transmission in a truck before but in the manual of my truck it specifically says not to put the clutch in then breaking because disconnecting the engine from the drive train removes any breaking power the engine itself can provide. It is more effecient to down shift while using the break at the same time to slow down especially when a load is being hauled. The only time the clutch should be popped when stopped is to keep the engine from stalling.
I'd like to apologize for my previous comment. I spoke as though I knew what I was talking about, while in reality, I didn't. Directly after my post, I did a little research and quickly found that my logic, as sound as it was in my head, is simply not sound in the real world.
While I love manual transmissions, and my in depth research into transmissions in general is almost solely on manuals, due to the sparsity of manual transmission vehicles at my disposal, I have very limited experience behind the wheel of them. So please forgive me for talking as though I knew what I was talking about. ^///^*
Mia Ray It's no problem learn something new every day.
Amazing and detailed video. This took lots of effort, I can tell because I've tried 3-D modelling. Great work.
3:25
"Let me introduce you to rev matching, double clutching, and for gods, clutchless shifting."
And what will he say about "heel toe"....?
@@jonwatson9765 heel toe is a method to rev match
Ahh yes some nonsense only americans do, because using a manual transmission car a normal way, is too boring.
Seriously Who the hell double clutcy and rev match????
@@anderstermansen130 Because Freedom :)
@@anderstermansen130 I’m European and I do =D Got a cable operated throttle body, got that severed the other day, tied it up on spot and had the throttle pedal way higher than the brake... As a result, I wasn’t really able to double clutch heel-toe rev-match and I was pissed to no end
Bro my manz did his best to put themost smartest words to describe this
3:05 this is what i call SATISFYING
"when breaking clutch must be pressed with manual" - nope. theres engine breaking, which means just releasing the gas pedal. if you wanna use the brake you just should release the gas pedal. engine braking and brake-braking work together. when you STOP is when you need to press the clutch. please use "must" responsibly
Ujvári Mátyás Youre right
or just press the clutch and put it in neutral.
while doing like 90 on HW and in front is someone with 60 or 70? we were talking about slowing down not "cruising" o.o"
VoidRapt
I may have heard wrong, but he never says "when breaking, clutch must be pressed...", he says "before you press the break pedal, the clutch pedal must be pressed down completely". Two different things.
95% of the comment section is kids who aren't old enough to drive yet.
ibro314 including urself
ibro314 bitch im 11 and i can drive a automatic car, so fuck off lel
Eggpie_614 Plays ah cmon, manual is easy, when the rpm is high, just press the clutch pedal and move the gearshift, when the car is about braking, press the clutch pedal once again and finally move the gearshift backwards instead forward, like from 5 to 4 to 3 and so on until the car increasing the speed
automatic cars is simple, just press the brake pedal and move the gearshift from p (or n) to d, and u can drive the car with one pedal,
but notice, never sudden brake the automatic vehicles, espicially from high speed, because sudden brake can cause the engine to stall
pretty soon all cars will become self driving and all these kids won't ever have the experience of driving. that, in addition to the gig economy of uber and lyft, where you pretty much rely on others to do the driving for you. much like they no longer are taught cursive or how to properly make their signatures. many have atrocious handwriting skills and are dependent on their computers to create letters or notes that others can read. driving will become a lost art that only those born before 2000 will know or remember how to perform.
The future is looking bright
Very well explained video. I didn't understand a thing but that's on me
I have experience of driving with both of them.
my advice: if you drive a lot in the city or somewhere that you have to change gear a lot, pick auto. otherwise manual is better from every aspect. if you become professional in driving you can even change manual without significant loose of converted power by controlling the clutch and fast gear changing.
Behrooz KHaleghi Rad i have tested both transmissions too. i prefer manual even in the cities. it provides good performance at low speed and more fuel efficient. it depends on the car too, but for me manual is better
I have them both with more than 10 years A/T experience, the automatic transmission (A/T) ones came from different generations, one has hill sensing and the other doesn't have one. I prefer automatic over manual transmission for highway and city commute because A/T is simpler to operate, I don't need to change gears, in a traffic stop just push the brake pedal, no need to change gears and my left hand is free to do other things, eating burger etc..lol. As of acceleration, for stop & go and highway driving, acceleration is almost instantaneously, the A/T will respond quickly adjusting its gear and pick up speed even if I push gas pedal at about 120-140 km/hour, leaving M/T car behind (You almost can't do this if you use M/T). The M/T is probably my preferred choice If my daily commute in a hilly area and need to overtake cars alot, M/T is more responsive than A/T.
I like manuals, myself. As far as city driving, it VASTLY depends on the weight of the clutch. ;)
Behrooz KHaleghi Rad
Ary Himawan lol leaving m/t behind? Try again
Hmm, never seen a Front-wheel drive BMW Z4 before
Lucas Joona that’s because it’s a 125
@@devinbender8428 There is no BMW FWD cabs. The only FWD cars at BMW are series 2 and X1 S Drive. Even the series 1 hatchback is RWD...
m1l15lvoue new 2019 BMW 1 hatch is FWD
@@m1l15lvoue x2
I will still always insist that everyone should know how to drive a manual car..
In europe 90/95% of cars are manual. If you have drive license you can drive manual cars. You have to drive manual car when you get your license ;)
Not true, if you have your drive license with a manual you can drive both but if you get a license with a automatic car you can only drive automatic.
In most european countries you only get license with manual car ;)
why?
Silverwing, that's a bit of a double-edged sword situation. If nobody seems to know how to use one, how can they steal your car? : )
The vast majority of cars in Europe are manual transmission and gear change becomes a smooth with experience.
I drive both manual and Automatic, finding Automatic sluggish when it come to gear changes and jolts when doing so.
I also found gear switching up and down repeatedly , when going up hills.
In a manual you can hold the gear and increase the reves until you can have enough torque to hold the higher gear
3:28
Never a smooth experience huh? I take offense to that.
The reason it won't be smooth is the driver. people don't understand the concept it is rough because the driver let's of the clutch before give a little gas or slamming off the clutch that is why it would be rough if you give a little gas while letting off its smooth shifting it takes practice like everything else
If im about to go up a hill ill shift down meanwhile if its automatic you'll need plenty of gas to make the hill meaning more gas usage . ill keep my standard
Its all up to the driver whether it will be rough or smooth af
@@saba7733 true
Yeah this video is retarded holy shit lol
We need to bring someone back from the 20's that actually knows how to explain this stuff to the regular public
Wow a random video... That was kinda good to watch
Even though i understood nothing i find the animations satisfying to watch
hey guys i know you you have done a lot of hard work on making this video i really appericiate your work this type of your animated video helps us a lot to understand the insight of the vehicals and many other machines which is normally very complicated
First time ever seeing a FWD BMW.
i'm 0% sure this is a kit car
I was thinking the same thing lmao
Reuben U ehh BMW 2 series is fwd and 2018 BMW 1 series will be fwd
Reuben U my thoughts exactly! Lol
iHeart GT86 {KatyCat} The engine in this animation is a front wheel drive
Real drivers use manual
Daniel Tavares Ancient mentallity. Only to pose with your technical knowledge. Thinking about the future is smarter, which implies no transmission at all. Go electric. :-)
Zzzzzzzzzzzzzzzzzzzz
Daniel Tavares I love the good stuff, manual isn't one of them.
But in a truly great electric, there will be a multi-speed transmission. ;)
Richard van Pukkem But that's no fun