كنت ابحث عن تشكيل هذه الدائرة بدون كثرة العناصر الإلكترونية شكراً لك غاية في الروعة لكن سؤالي كم وات waat تستهلك هذه الدائرة على تيار 12V اتابعك من سوريا
My only observation - IGBT stands for Insulated Gate Bipolar Transistor there is a gate like a FET, but these have greater power handling capability than any power FET/MOSFET or BPT have.
birde altın eritmek için kullanılan indiksiyon yapsanız çok iyi olur. potaya koyunca erimesi için güçlü bir indüksiyon lazım. bizlere. o zaman size minnettar oluruz. buna ihtiyacımız var.
Good and wonderful work. You always can make a 12-volt induction laser cooker. The best tool is the same as the basic cooker. I tried it on igbt, but the heating is slow despite putting 10 0.33 capacitors to raise the vibration frequencies.
While more capacitance will raise the circulating current in the inductor coils, it will cause the circuit to oscillate at a lower frequency, not higher. 10 times the capacitance will give (1 / (sqr 10)), or a little over 1/3rd of the frequency. To cope with the increased circulating currents in the coil circuit, you will need much heavier gauge wire, too, or the resistance will limit the current, regardless of the capacitors' theoretical maximum.
60 watt led trafosu ile deneme yaptım, maket bıçağı belli süre ısındı, sonra transistör bozuldu çünkü güç kaynağı yetersizdi, şuan kısa devreden dolayı bobin ısınıyor, sağlık olsun😊
A votage is applied to the transistor base that turns on, this will force a current through the capacitors that will charge up negatively, when it reaches a certain negative voltage, it will turn on the second transistor that is forcing a current in the opposite direction, this opposite current will first discharge the capacitor and then charge it positively. Hence it will generate a positive voltage which will turn on the first transistor again, and so on. It uses the same principle as with a mosfets and diodes, an IGBT is just a transistor with a diode (it is an oversimplified view of an igbt but that will do in this case)
@@yannor7 Thank you so much for the explanation. Another question if you please. Can this circuit be used to make a simple inverter? Does it give a decent frequency?
0:25 - как говорил наш замечательный сатирик, Аркадий Райкин: "Оптический обман зрения." Вы видите катушку, а ее нет (... без катушки!) Хотя по большому счету, при таком соотношении - несколько наногенри и аж три десятых микрофарады, наверное можно сказать, что катушки нет. И *это* работает? Добротность такого контура на 600-х килогерцах должна быть ниже нуля.
Why didn't you show the current at 12v? Why haven't you answered the questions asking what it is? We know it will be higher. We just want to know how high to source correct PSU. Is 12v max device can take?
Since it is in parallel, it looks like it can handle 6 amps or higher. Just look at the IGBT chip. His other induction heater designs look like they can go up to 48 amps. I'd power it from a capacitor before turning on the PSU since it is still a mosfet susceptible to unstable power fluctuations. The wrong PSU can fry mosfets from what I remember.
I'll build one for sure. I have to check the scrap box/bag for IGBT or some old welder boards I have in the shed. The 12 volts would be great for camping. I was going to try the Z44 single one you showed, but maybe this one first (less coil work). My FNIRSI scope was DOA on arrival and NO support from them so I can test me new SIGLENT scope I bought. I will add heatsinks too.
Hola buenas tardes mi pregunta es la siguiente con el transformador de aislación ,,, ¿ Me valdría un transformador de aislación para evitar interferencias de toda clase con un transformador de estas características para equipos de Radioaficionado, ya que hice algunas pruebas y la verdad que si que desaparecieron interferencias muchas ,¿ Esto es viable para un cuarto de radio??? Saludos desde España
s.aleyküm zafer bey kaynak makinemde aycibiti salamlıgını normal bi multimetreyle nasıl ölçebilirim yani sökmeden ölçülürmü yoksa hepsini ayırmammı gerekir yani kısacası igbt saglammı bozukmu nasıl ölçülür anlatımlı bir video yaparsanız çok sevinirim
@@ZAFERYILDIZ52 , hola Zafer, recientemente he replicado dos de tus videos, y los he subido a mi canal de youtube; tus vídeos de: "Circuito Flip flop super power hecho con mosfet" y el otro era el vídeo de: "Haga su propio calentador de inducción", me funcionan perfectamente, gracias. El calentador por inducción con mosfet, lo hice con Igbt's y también funcionó. Un saludo amigo, gracias 🙂.
You say no coils and no transistors, then what are the thick wire rings with the center tap, scotch mist? And what are the disguised items that look very much like a transistor? Lastly, If anyone wanted to make a copy of your so-called design without transistors or at the very least a transistor number the job is impossible. Think again, my friend.
Hola! Estoy buscando para hacer una calefaccion de 12v. La ide es hacer pasar un tubo con agua/refrigerante a traves de la bobina con una pequeña bomba. Ese liquido pasa por un pequeño radiador y un ventilador hará la disipacion del aire caliente al recinto. Hay que controlar las velocidades de la bomba y del ventilador para lograr eficiencia. Alguien que me pueda ayudar con esto?
كنت ابحث عن تشكيل هذه الدائرة بدون كثرة العناصر الإلكترونية
شكراً لك غاية في الروعة
لكن سؤالي كم وات waat تستهلك هذه الدائرة على تيار 12V
اتابعك من سوريا
My only observation - IGBT stands for Insulated Gate Bipolar Transistor there is a gate like a FET, but these have greater power handling capability than any power FET/MOSFET or BPT have.
4ı
DoesItWorkWithMosfetOrBipolar?
IGBT consists a transister a mosfet and a diode
Какая схема этого транзистора?
Excellent job.
Respect BRO 🇰🇿
OMG crazy!!!!!! It works at 5v too. I'm gonna use this to make a wireless charger... Thanks Yildiz
Everything started up great. I want to try to use this circuit to drive a Tesla coil. Is it possible to adjust the frequency to select resonance?
birde altın eritmek için kullanılan indiksiyon yapsanız çok iyi olur. potaya koyunca erimesi için güçlü bir indüksiyon lazım. bizlere. o zaman size minnettar oluruz. buna ihtiyacımız var.
Very smart idea and also dc to ac inverter , very good and well done.
Good and wonderful work. You always can make a 12-volt induction laser cooker. The best tool is the same as the basic cooker. I tried it on igbt, but the heating is slow despite putting 10 0.33 capacitors to raise the vibration frequencies.
While more capacitance will raise the circulating current in the inductor coils, it will cause the circuit to oscillate at a lower frequency, not higher. 10 times the capacitance will give (1 / (sqr 10)), or a little over 1/3rd of the frequency. To cope with the increased circulating currents in the coil circuit, you will need much heavier gauge wire, too, or the resistance will limit the current, regardless of the capacitors' theoretical maximum.
lol.MaybeVoltageNeedsToBeHigher.10Capacitors?MaybeLessIsBetter.
Zafer bey spirin çap büyütürsek! İlave etmemiz gereken parça olurmu? Pota için kullanmak istiyorum..harika olmuş.elinize sağlık
Creative, as usual, great ideas and projects. Greetings to you, my dear brother
thanks we are here to produce not copy
üstadım 220 volt ve kuvvetli olan bi indüksiyon ısıtıcı hiç bi yerde bulamadım sizden umutluyum ve sürekli takipteyim
60 watt led trafosu ile deneme yaptım, maket bıçağı belli süre ısındı, sonra transistör bozuldu çünkü güç kaynağı yetersizdi, şuan kısa devreden dolayı bobin ısınıyor, sağlık olsun😊
Great but am just wondering how such a simple circuit can produce a sinosoidal wave. Would you please explain?
A votage is applied to the transistor base that turns on, this will force a current through the capacitors that will charge up negatively, when it reaches a certain negative voltage, it will turn on the second transistor that is forcing a current in the opposite direction, this opposite current will first discharge the capacitor and then charge it positively. Hence it will generate a positive voltage which will turn on the first transistor again, and so on.
It uses the same principle as with a mosfets and diodes, an IGBT is just a transistor with a diode (it is an oversimplified view of an igbt but that will do in this case)
Btw if you use a chemical capacitor for this circuit, it will blow up. Please don't do that.
@@yannor7 do you mean electrolythic capacitors???
@@yannor7 Thank you so much for the explanation. Another question if you please. Can this circuit be used to make a simple inverter? Does it give a decent frequency?
@@sidamarali3030 No. Its frequency is too high.
great 👍
Thanks my Frend
Brother how I can use this design as induction plate,mean where I have make winding setup for metal plate heating. Waiting for reply. Thanks
أنت رائع
أتابعك من مصر أم الدنيا
0:25 - как говорил наш замечательный сатирик, Аркадий Райкин: "Оптический обман зрения." Вы видите катушку, а ее нет (... без катушки!)
Хотя по большому счету, при таком соотношении - несколько наногенри и аж три десятых микрофарады, наверное можно сказать, что катушки нет.
И *это* работает? Добротность такого контура на 600-х килогерцах должна быть ниже нуля.
Черпает энергию из эфира! Срочно запретить! ЭЙ НЕФТЯНИКИ! ВЫ ГДЕ ТАМ?
I am not getting IGBT 30f126 in the market. Which other IGBT can I use instead with exactly the same pin
should use 1600v mkp? i want to try 24v input voltage with 250v mkp, will that work? ty
فيديوهاتك مميزة وعلمية ارجو ترجمه للعربيه وايضا اخي ارجو معرفه ماالفائده من كل مشروع انا متابع قاناتق علي اليوتيوب من زمن طويل اخوك من فلسطين ❤
Ok , it was running on 12 volts but what was the current draw ?
He's using a similar circuit in a different vid, where it draws 5 amps
Why didn't you show the current at 12v?
Why haven't you answered the questions asking what it is? We know it will be higher. We just want to know how high to source correct PSU.
Is 12v max device can take?
Since it is in parallel, it looks like it can handle 6 amps or higher. Just look at the IGBT chip. His other induction heater designs look like they can go up to 48 amps. I'd power it from a capacitor before turning on the PSU since it is still a mosfet susceptible to unstable power fluctuations. The wrong PSU can fry mosfets from what I remember.
Teşekkürler Zafer bey
you build beautiful circuits sir
Gracias.
Built one for heating H²O based liquids in a closed test tube or vacuum metal casting chambers.
Did it work for you?
How long can you use this unit before you have to give it a brake ??? Duty cycle I suppose.
If the temperature were lower it could be used as a heating element for absorption refrigerator #RV #camping off-grid air-conditioning
I'll build one for sure. I have to check the scrap box/bag for IGBT or some old welder boards I have in the shed. The 12 volts would be great for camping. I was going to try the Z44 single one you showed, but maybe this one first (less coil work). My FNIRSI scope was DOA on arrival and NO support from them so I can test me new SIGLENT scope I bought. I will add heatsinks too.
Now imagine putting a metalpipe between that ring and heating water like that :) Very little energy loss.
👌
Thanks
Çıkış gücü yükseldiğinde bir kaç milyon beyin hücrelerinize elveda diyebilirsiniz. Tebrikler.
Hello sir . amazing work . will it work on 12 DC battery? and how long can it work with out or brake ? thank you.
Viy s realizar uno con bobina que se pueda abrir en dos partes , x mo oara dikfar caños utilizando estaño o plata.
Üstat ısınan borudan su gecirirsek kalorifer peteklerine verirsek ısıtma problemimiz çözülmüş olurmu.pahaliyami gelir.tesekkurler
good work
Helal olsun kardeşim Rabbim seni başımızdan eksik etmesin Gaziantep ten selamlar olsun
Teşekkürler kardeşim eksik olmayin Antep'e Sevgi ve saygılar allah birdaha böyle bir acı göstermesin
Amin amin
However, if we heat the iron pipe and pass water through it, can we heat the house?
wow.. good idea, but do i need to input frequency? thank you sir
The video showed input frequency. 620,000Hz
Hola buenas tardes mi pregunta es la siguiente con el transformador de aislación ,,, ¿ Me valdría un transformador de aislación para evitar interferencias de toda clase con un transformador de estas características para equipos de Radioaficionado, ya que hice algunas pruebas y la verdad que si que desaparecieron interferencias muchas ,¿ Esto es viable para un cuarto de radio??? Saludos desde España
Can a 40N60 be used in place of the 30F126?
Thanks!
iyi çalışma, indiksiyon ocağına uyarlama da bir değişiklik gerekir mi ?
What was the current drawn at 12 volts, while heating the metal blade, please?
500 microamps. Pure wizardry.
What if you use a thick metal would it have same result?
Elinize sağlık Zafer bey. Market bicagini eritmek ne kadar surer
Why do we need souch high voltage capacitors for a circuit like this??? 400V capacitors should be enough, or not?
If the voltage drops, efficiency and frequency will be adversely affected.
Se pude hacer algun tipo de parrilla para calentar alimentos con este metodo?
😲😲😲👍👍👍👍zo‘r va ajoyib...
rahmat
Neat build. Why the hostility towards hobby knives?
Can we touch this copper coil, does it have current, is it dangerous?
s.aleyküm zafer bey kaynak makinemde aycibiti salamlıgını normal bi multimetreyle nasıl ölçebilirim yani sökmeden ölçülürmü yoksa hepsini ayırmammı gerekir yani kısacası igbt saglammı bozukmu nasıl ölçülür anlatımlı bir video yaparsanız çok sevinirim
Terimakasih gan...sudah berbagi ilmu 👍👍👍
Источник питания 12v или 220v ответти пожалуйста
Can you put in parallel more transisors in order to increase the current?
Да, только на коллекторы или эмиттеры нужно ставить мощные резисторы
Ano, existujú IGBT tranzistory pre prúd 300 A
Дүү маш бүтээлч санаа байна.... Гайхалтай ...👍👍
Mulțumesc, thank You my friend , danke meine freund....
بارك الله بك سؤال
كم أمبير تسحب عند ١٢ فولت للتغذية
8 أمبير إذا كان المعدن سميكًا
@@ZAFERYILDIZ52 💜
Lò sưởi cảm ứng của bạn rất tuyệt vời
MERCI!
Hi!
12v ok
Amp??????
Muy bueno Zafer!! Graciass 😘
Gracias por los comentarios y el apoyo.
@@ZAFERYILDIZ52 , hola Zafer, recientemente he replicado dos de tus videos, y los he subido a mi canal de youtube; tus vídeos de: "Circuito Flip flop super power hecho con mosfet" y el otro era el vídeo de: "Haga su propio calentador de inducción", me funcionan perfectamente, gracias. El calentador por inducción con mosfet, lo hice con Igbt's y también funcionó. Un saludo amigo, gracias 🙂.
Este es mi vídeo inspirado en el tuyo:
ua-cam.com/video/82x-pEuwFR0/v-deo.html
Barocalloh. Omad your Olsun.
Amazing 👍😉
👉❤️👈
فيديوهاتك مميزة وعلمية نرجو ترجمتها الى العربية
Isn't igbt a type of MOSFET?
zafer abi kullandığın fnirsi ses anfisi çıkışını kaç v kadar ölçer?
Sir, in the same way, MOSFET can also be turned on?
no, provided that this circuit is suitable for IGBT and has the same features
@@ZAFERYILDIZ52 Thanks for replying
Good performance 👌.
Thanks My friend
@@ZAFERYILDIZ52 Thank you 😀.
Hi, I sent you an email yesterday!
Usta videolarını beğenerek izliyorum arduino için bir mosfet H bridge devresi yapmam lazım onun hakkında bir videoda yapar mısın?
Hanaldaki yon kontrol devresini mosfet ile sürebilirsiniz ancak yakin zamanda bir tane daha planlıyorum
السلام عليكم ورحمة الله وبركاته ماقيمة الجهد وما قيمة التيار وشكرا
لم توضح القراءة في الفيديو
Abi eline sağlık bir sorum olacak 0.1uf 1600v yerine 400-600v kullansak olurmu
Ano
عمل دائره لساعه حائط ترن كل ساعه وتعرفك كم الساعه
Make a circle wall clock that rings every hour and tells you what time it is
Halka tele bi metal ekleyerek elektrik girişine anahtar koyup lehim makınası yapabilirsin kolay gelsin 👍
the soldering between the coild wirind and capacitors will melt off if put it together this way...
Nice idea
Yine bulunmayan içeriklerden👍
Teşekkürler kardeşim
You say no coils and no transistors, then what are the thick wire rings with the center tap, scotch mist? And what are the disguised items that look very much like a transistor? Lastly, If anyone wanted to make a copy of your so-called design without transistors or at the very least a transistor number the job is impossible. Think again, my friend.
Could this be used to generate power if you spun a magnet inside it?
no.ForThisGeneratorsWereInvented.🤑
.1 uF 1600V alone is $165/ea. so what’s the point building something like this, while a car heater can give you heat for $15/ea
Peki benim sorum kristal eklemek gibi basit eklemelerle frekansın nasıl kontrol edileceği ile ilgili..
Hi, wieviel Volt und Amper schaffen die Igbt´s
Ótimo trabalho 👏 sucesso aí irmão 👍
I do not have igbt if we work bjt transistor?
Love you
Muy interesante el proyecto.🤔
620 khz 😮 amazing 👍
Thanks
👍👍👍 pode ser usado para soldar tubos de cobre de centrais de ar condicionados split??.
how would you fit the tubes inside the coil? there is a special clamping tool to take care of a/c fittings without the need to solder.
@@carlosgaspar8447 construir uma bobina em forma de panqueca e dobrar em forma de U.
Dios te bendiga puede calentar cualquier metal..?
Es posible tomar calor de todos los metales afectados por el imán.
هل ناستطيع ان نجعله لطهي طعام وكيف ولك جزيل الشكر 🌹
pensé que ibas a hacer algo potente, eso es para calentar la navaja antes de afeitarme
Gostei muito
Berapa maximum & minimum voltage input?
very easy to use
Selamun Aleyküm... Büyük yük kamyonu için 24 volttan 12 volta ve 15 Amp DC trafo yapmak için gerekli parçalar nelerdir?
Amper konusunda ucu açık bir ürün haznesi olsada internette dc dc voltaj düşürücü yazarak onlarca ürün bulabilirsiniz
Definitely worth it to have a heavier version for a service truck but didn’t cost a fortune for a change, could make a mint if was reasonably priced
Zafer usta 30F126 IGBT den başka alternatif olarak ne kullanabiliriz
Degerlerine bakın yakın değerde hepsi olur 30F127/128 birbirinin yerine olur bunlar
elinize sağlık hocam
iyi günler
1150 derece altın eritmesi için ne yapmamız lazım
bu devre ile ulaşabilir miyiz
Ellerine sağlık abi kart tamir vidio lari da bekliyoruz
Hola saludos desde Argentina, se puede hacer una estufa con un cooler, verdad?
Hola! Estoy buscando para hacer una calefaccion de 12v. La ide es hacer pasar un tubo con agua/refrigerante a traves de la bobina con una pequeña bomba. Ese liquido pasa por un pequeño radiador y un ventilador hará la disipacion del aire caliente al recinto. Hay que controlar las velocidades de la bomba y del ventilador para lograr eficiencia. Alguien que me pueda ayudar con esto?
Iyi kardesim 👍👍👍👍👍👍
Teşekkürler kardeşim
Teşekkürler kardeşim
liga em quantos volts?