Nissan Rogue Oil Leak Fix (Oil Cooler Gasket Replacement) - 2.5L engine

If you have a Nissan Rogue with an oil leak near the right front tire, chances are your oil cooler gasket is leaking. In this video I'm showing step by step how to locate and replace it.
(This procedure and parts could also work on 2007-2013 Nissan Altima and Sentra with 2.5L engine - please check the compatibility with an authorized dealer) 2011 Nissan Rogue AWD 2.5L
Timestamps:
0:00 Intro
0:35 Oil Leak Location
1:02 Oil Cooler Gasket Removal
4:41 Conclusion
Products Used In this Video (same or similar):
Oil Cooler (Aftermarket) - amzn.to/36lgkaY
Oil Cooler Gaskets (Dorman) - amzn.to/3JI946E
Oil Cooler Gaskets (Fel-pro) - amzn.to/3KKjkg3
Oil Pressure Sensor Socket - amzn.to/3rrjh0O
A few more products I personally own and use:
Upholstery Remover - amzn.to/32dXTiS
Pocket screw driver - amzn.to/2HQrPcE
Pocket Flashlight - amzn.to/3j32AVF
Basic Hand Tools - amzn.to/2I91cBb
Drill and Impact Driver - amzn.to/2WCMxzI
Cordless Ratchet - amzn.to/2KcBsBw
Portable Jump Starter - amzn.to/2HR0V4l
Code Reader - amzn.to/2HRwdI4
Fluke Multimeter - amzn.to/2HQOx42
Hook set - amzn.to/2JUdfTi
[All Links Are Affiliate]
Disclaimer:
Due to factors beyond the control of Make It Easy Mechanic, it cannot guarantee against improper use or unauthorized modifications of this information. Make It Easy Mechanic assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Make It Easy Mechanic recommends safe practices when working on vehicles and/or with tools seen or implied in this video. Due to factors beyond the control of Make It Easy Mechanic, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Make It Easy Mechanic.

[@oa5275]

Thank you very much for the video. Very clear and concise information. I believe all Rogue's over 200k kms (125k miles) have to be checked for this issue.
I wanted to paste Nissan part numbers here for convenience:
- Oil cooler gasket = 21304-JA006
- Oil cooler o-sing seal = 21304-JA06A
Of course the Fel-Pro or Dorman sets you've provided in the links would be much more affordable solutions.

[@TheScantraaxx]

Nice diagnosis thanks 🙏

[@Beachesnoars]

On our car I just bought. The ac pulley locked up and the owner kept driving it and it was very hard to turn over. Ended up burning up the starter. So I got all that repaired today and fired it up. It immediately started leaking. Your video helped us find the leak and now we will be ordering that part to finish up the car. Thanks again for the help!

[@ronbunker5778]

Thanks so much for this video! This is exactly what my 2009 Rogue is doing and thanks to you I now know what needs fixing!

[@kasualskeptik2584]

Very clear instructions and good diagnosis...!! Thanks...

[@francisguchie1973]

nice and simple and affordable repair

[@davedeatherage4902]

Thanks, excellent teaching.👍🏻

[@patricecool7747]

Very helpful bro

[@isaacokobi982]

Thanks for the video

[@Sally-nd5pc]

Hi, how can i contact you about the sponsorship?

[@gebremikaelhagos7988]

✅✅✅✅👍👍👍👍🙏🙏🙏🙏🙏

[@dcall2533]

Should I rub oil over the new gaskets prior to installation?

[@MakeItEasyMechanic]

You dont have to. You can put a little oil on the rubber O-ring gasket. But I would keep the "paper" gasket and the mating surfaces dry.

[@brianhenry1427]

Is that the transmission oil cooler?

[@MakeItEasyMechanic]

No, it's engine

[@AwakeDude911]

did this job last week ...your going to reach in there pretty far jacked up (not on a lift) so its gonna be pretty unconformable for atleast 30 mins ... the cooler had also sucked up some hard orange plastic bag type stuff (no screens i seen anywhere) so it was clogging the oil return as well (horrible design) ... if not done it would have blown the motor!!! not a hard job but you'll need gloves and long sleeves or your going to get cut up on the rotor and strut .... my 2 cents

[@thekingsilverado3266]

Always tighten bolts to love your car strength.. Never ever tighten to super gorilla strength or hate your ex girlfriend strength...

[@kirankumarkomatapalli4122]

Hi sir my name Kiran
I am from India
I want car unlock it

[@ahumanjustbeing2466]

$16 for parts...$164 for labor...sigh

[@quantummandavid]

Braaaaaa your fcking amazing