When we swapped from the 20-round mags to the 30-rounders, back in the 1970s we used 550-cord with short loops and 500 mile-an-hour tape, like you demonstrated. We didn't have large loops because they would get caught on jungle vegetation. Today I use Magpul's original rubber assist loops, but I put them on 90-degrees from what they were originally intended so just a small amount is over the end but still provides a good grip surface.
Its awesome to hear stories and experience from older generations that help support the reasons behind the why! We appreciate your input, knowledge, and experience! Don't be shy with it I know a lot of guys appreciate that older wisdom, and it helps newer guys figure out their kit setups
Solid tutorial as usual. We used to tie knots at the end of the 550 and tuck em under the baseplates ( slide baseplate 1/2 way tuck knots either side re secure)also put 1/2 strip of 100 mile an hour tape in center of loop to to keep separated, keep ‘em long enough for a gloved finger but not too long they snag -also hook a D ring on our I B A to retain empty mags with the 550 since we didn’t have dump pouches - circa 04-05 O I F II
So those 20 round straight wall magazines were designed to use tilting followers because you have rounds that inherently curve when stacked in a straight body. The first gen 30s used those tilting followers as a carry over until they realized it wasnt needed in a curved magazine.
Lots more content is on the way .. taking about 60 days off work to be able to produce content for the website and UA-cam! Life is just very busy at the moment. It’s good to see you on the channel and thank you for your support
The magpul anti tilt follower will cause nose dive in very early vietnam era adventureline GI 30rd mags, it happens in 15-16th shot. I stuck with the original black tilt follower and the problem is gone. Any improved mags made after M16A2 came out are good to go with magpul anti tilt:)
Great ideas, Brother !!! We conducted magazine maintenance to avoid or prevent malfunctions, and used a tiny bit of lubrication as well. A rag and a "hard" toothbrush (nylon bristled) works wonders.....even in sandy and wet environments. P.S. The 550 cord modification may get caught when using those bungee cord retention systems on modern chest rigs and such. Speaking from experience. Be careful. Train with them before needing them. Keep up the great work !!! Stay safe.
Appreciate the input I know that it will definitely help those reading through the comments section determine the best course of action for their kit setup!
When we swapped from the 20-round mags to the 30-rounders, back in the 1970s we used 550-cord with short loops and 500 mile-an-hour tape, like you demonstrated.
We didn't have large loops because they would get caught on jungle vegetation.
Today I use Magpul's original rubber assist loops, but I put them on 90-degrees from what they were originally intended so just a small amount is over the end but still provides a good grip surface.
Its awesome to hear stories and experience from older generations that help support the reasons behind the why! We appreciate your input, knowledge, and experience! Don't be shy with it I know a lot of guys appreciate that older wisdom, and it helps newer guys figure out their kit setups
Solid tutorial as usual. We used to tie knots at the end of the 550 and tuck em under the baseplates ( slide baseplate 1/2 way tuck knots either side re secure)also put 1/2 strip of 100 mile an hour tape in center of loop to to keep separated, keep ‘em long enough for a gloved finger but not too long they snag -also hook a D ring on our I B A to retain empty mags with the 550 since we didn’t have dump pouches - circa 04-05 O I F II
Very good !!!!!!
So those 20 round straight wall magazines were designed to use tilting followers because you have rounds that inherently curve when stacked in a straight body. The first gen 30s used those tilting followers as a carry over until they realized it wasnt needed in a curved magazine.
The more you know
The king has returned
I appreciate it, we're always learning, remembering, and sharing things here so stick around we've got more content on the way
Good to see you again, I hope all is well. I look forward to seeing more content.
Lots more content is on the way .. taking about 60 days off work to be able to produce content for the website and UA-cam! Life is just very busy at the moment. It’s good to see you on the channel and thank you for your support
These tutorials are invaluable. Easy to overlook but critical. Great work!
Agreed and Thank you for the comment!
The magpul anti tilt follower will cause nose dive in very early vietnam era adventureline GI 30rd mags, it happens in 15-16th shot. I stuck with the original black tilt follower and the problem is gone. Any improved mags made after M16A2 came out are good to go with magpul anti tilt:)
Awesome video very informative and thanks for sharing!
Very good common sense info
Typically don’t comment. But enjoyed this one a lot.
I appreciate you watching and interacting 😃
Buy magpul loops lol.
Vietnam War books give good tips on how to mod or improve the mags.
The magpul loops are awesome however I have seen them fall off and I have seen them break this is an alternative to them
@@LegionPreparedness oh easy Marine hack, grip tape and zip tie, cut the end off, this reinforces the magpul loop.
You won't be able to use the MOE loops in the ALICE pouches.
I love this channel
appreciate you !!!!
Thoughts on the 40 round metal mags are they worth looking into or no
You can go that route or just buy extensions for the polymer mags
Comment
Great ideas, Brother !!!
We conducted magazine maintenance to avoid or prevent malfunctions, and used a tiny bit of lubrication as well.
A rag and a "hard" toothbrush (nylon bristled) works wonders.....even in sandy and wet environments.
P.S. The 550 cord modification may get caught when using those bungee cord retention systems on modern chest rigs and such.
Speaking from experience.
Be careful.
Train with them before needing them.
Keep up the great work !!!
Stay safe.
Appreciate the input I know that it will definitely help those reading through the comments section determine the best course of action for their kit setup!