Building a blow-through (Part 1)

Поділитися
Вставка
  • Опубліковано 25 сер 2024
  • Modifying a carburetor for blow-through - Part 1: Fuel bowl and body changes.

КОМЕНТАРІ • 20

  • @kerrygatling663
    @kerrygatling663 9 місяців тому

    Good video👍Nice, clean and simple mods.

  • @NoPrepFans
    @NoPrepFans 3 роки тому +3

    I’m excited to see this because I’m working on a 69 Ford with a 302 and I’m thinking of doing a turbo setup on it not 100% sure if I’m going to do it now or later down the road

  • @TurboJohnRacing
    @TurboJohnRacing 3 роки тому +2

    Gas hands coming up!

    • @1fastpickup
      @1fastpickup  3 роки тому

      Lol...it’ll smell like the old days!!

    • @bevinsracing
      @bevinsracing 2 роки тому

      What size are you drilling nthe main wells and pvcr for E85..I had a c&s blow thru for gas but I want to switch to E85

  • @DustySteel
    @DustySteel 4 місяці тому

    Is it possible to make a small engine carb like a Keihin PWK 26mm a blow through carb? I’ve seen one video where I guy did it to a mini bike but doesn’t talk about the jetting. He says that he just blocks off a couple of “vents”. Are you willing to explain this? I’m going to continue to watch your videos on carbs for cars but small engine carbs would also be cool.

  • @kevinjohnson9372
    @kevinjohnson9372 3 роки тому +1

    Iv herd of ya and I like carbs i think there as good or better then fuel injection especially if there tuned right and the ignition is set up properly the vehicle should run with optimum performance and efficiency

    • @kevinjohnson9372
      @kevinjohnson9372 3 роки тому +1

      Iv seen turbo jon around but never herd of u till now

    • @1fastpickup
      @1fastpickup  3 роки тому

      John and I have been friends for years...back when he was running True Street/Real Street I was his crew guy (official spark plug changer and golf cart driver - lol) at all those races. ...if you scroll WAY back on my channel there's videos of John (and Bryan) dating back to 2011

  • @backyardbuilttrucks1
    @backyardbuilttrucks1 3 роки тому +1

    Guy in Austraila makes those power valves . Sell to simple stage . Also scs carburetor makes a better one.

  • @kevinjohnson9372
    @kevinjohnson9372 3 роки тому +1

    So I get the basic just of blow threw carbs but what about that old school shit wear u put the carb in a box on the intake

  • @jondahl3173
    @jondahl3173 3 роки тому +1

    Get a shotgun microphone, very hard to hear you. Watching this, going to do blow through card single turbo myself on a street truck.

    • @1fastpickup
      @1fastpickup  3 роки тому

      yeah sorry about the sound. I just started doing these and the built-in iPhone mic is not cutting it - lol

  • @steveboyer9995
    @steveboyer9995 3 роки тому +1

    So how does the power valve get its signal?

    • @NoPrepFans
      @NoPrepFans 3 роки тому

      Vacuum it depends on what size you are running to how much vacuum to close it

    • @steveboyer9995
      @steveboyer9995 3 роки тому

      But you blocked off the hole that provides the signal

    • @1fastpickup
      @1fastpickup  3 роки тому +2

      The boost referenced is backwards from a regular PV. A normal PV is open by default and vacuum holds it closed...a boost referenced is held closed by the spring and the boost in the fuel bowl "pushes" it open. So you don't want vacuum (or boost) in the body side.

    • @NoPrepFans
      @NoPrepFans 3 роки тому

      @@1fastpickup thanks for explaining this it makes sense to me better now

  • @AdalbertoBadilla
    @AdalbertoBadilla 2 роки тому

    Hello, i saw the microsquirt next to your solid state relay are you using it to control your timing?? Cheers from california🤟🏻🤟🏻🤟🏻

    • @1fastpickup
      @1fastpickup  2 роки тому +1

      Yeah I ran fuel injection and timing with it previously...so i just removed the FI side and left the timing controlled with it. That same unit has been in my cars since 2013!